Patton electronics SmartNode 4830 Series Manuel utilisateur

SmartNode 4830 Series

Analog VoIP Integrated Access Device

Quick Start Guide

Approval

–Models that are equipped with telecom interfaces have been approved for connection to the

public telecommunication network as listed under PSTN regulatory compliance.

Important

–This is a Class A device and is intended for use in a light industrial environment. It is not

intended nor approved for use in an industrial or residential environment.

Part Number: 07MSN4830-QS, Rev. C

Revised: February 8, 2012

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

2SmartNode 4830 Series Quick Start Guide

• Do not open the device when the power cord is connected. For sys-

tems without a power switch and without an external power

adapter, line voltages are present within the device when the power

cord is connected.

• For devices with an external power adapter, the power adapter shall

be a listed Limited Power Source The mains outlet that is utilized to

power the device shall be within 10 feet (3 meters) of the device,

shall be easily accessible, and protected by a circuit breaker in compli-

ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all

applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2

& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet

(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are

rated for proper voltage, current, anticipated temperature, flammabil-

ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages

present regardless of whether the device is powered ON or OFF.

PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,

xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net-

work voltages” and to avoid electric shock use caution when working

near these ports. When disconnecting cables for these ports, detach

the far end connection first.

• Do not work on the device or connect or disconnect cables during peri-

ods of lightning activity.

In accordance with the requirements of council directive 2002/96/EC on

Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-

of-life you separate this product from other waste and scrap and deliver

to the WEEE collection system in your country for recycling.

This device contains no user serviceable parts. This device can only be

repaired by qualified service personnel.

WARNING

SmartNode 4830 Series Quick Start Guide 3

1.0 Introduction

This Quick Start Guide leads you through the basic steps to set up a new SmartNode (see figure 1) and to down-

load a configuration. Please note that this guide does not replace the detailed Software Configuration Guide and

the User Manual available online at www.patton.com/manuals/SN4830.pdf.

SmartNodes can be used for a wide variety of IP and voice over IP applications. To support and ease the configu-

ration of the SmartNodes configuration templates for the most important applications are available online at

www.patton.com/voip/appnotes.asp.

Setting up a new SmartNode consists of the following steps:

1. Connect a PC to the SmartNode, log in and configure your LAN IP address

2. Connect the SmartNode to the LAN

3. Download a configuration example, adapt it to your network, and load it onto the SmartNode

2.0 Powering up the SmartNode

1. Connect the SmartNode to the mains (AC) power source with the power cable.

2. Wait until the Power LED stops blinking and remains constantly lit. Now the SmartNode is ready

to configure.

Electrostatic Discharge (ESD) can damage equipment and impair electrical

circuitry. It occurs when electronic printed circuit cards are improperly

handled and can result in complete or intermittent failures. Do the follow-

ing to prevent ESD:

• Always follow ESD prevention procedures when removing and replac-

ing cards.

• Wear an ESD-preventive wrist strap, ensuring that it makes good

skin contact. Connect the clip to an unpainted surface of the chassis

frame to safely channel unwanted ESD voltages to ground.

• To properly guard against ESD damage and shocks, the wrist strap

and cord must operate effectively. If no wrist strap is available,

ground yourself by touching the metal part of the chassis.

CAUTION

4SmartNode 4830 Series Quick Start Guide

3.0 Connecting the SmartNode to the network

3.1 Connecting power and configuring the default IP address

Connect the SmartNode to the mains power supply using the included power supply and cable. When the RUN

LED stops blinking and remains lit, the SmartNode is ready.

The factory default IP settings are listed in table 1. If these addresses do not work with your network they must

be changed. Contact your network administrator if you are not sure which IP address to use in your installation.

Note The DHCP server is running on the ETH 0/1 of the SN4830 Series models. All Ethernet ports are pre-

configured and active.

3.2 Connecting to a PC and logging in

1. To access the SmartNode configuration, connect a PC equipped with an RS-232 console port to the Con-

sole port on the front of the SmartNode. Use the included black Ethernet cable and RJ45 to DB-9 adapter

for this purpose (Model 16F-561).

Figure 1. Connecting to a PC

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, flam-

mability, and mechanical serviceability.

Table 1. Factory default settings

Item IP Addresss Network Mask

WAN interface Ethernet 0 (ETH 0/0) DHCP DHCP

LAN interface Ethernet 1 (ETH 0/1) 192.168.1.1 255.255.255.0

DHCP server address range 192.168.1.10-192.168.1.19 255.255.255.0

CAUTION

Serial Terminal

Note A Patton Model 16F-561 RJ45 to DB-9 adapter is included with

each SmartNode 4000 Series device

Console

VoIP Gateway Router

ToIP Integrated Access Device

SmartNode4524

Link

100M

Activity

0/0

0/1

0/2

0/3

Enet0VoicePorts

Power

Run

VoIP Link

Link

100M

Activity

Enet1

SmartNode 4830 Series Quick Start Guide 5

2. Open a Terminal connection to the SmartNode. Use the Terminal program included with most PC operat-

ing systems (e.g. Hyper Terminal on Windows).

3. Type administrator as the login prompt and press the Enter key after the password prompt (do not type

anything for the password). A prompt will appear consisting of the IP address and >character.

password:

172.16.40.1>

4. Following log in, the SmartNode is in operator execution mode (indicated by >character in the command

line prompt). With the commands enable and configure, you enter the configuration mode.

172.16.40.1>enable

172.16.40.1#configure

172.16.40.1(cfg)#

3.3 Changing the IP address

1. Select the context IP mode to configure an IP interface.

172.16.40.1(cfg)#context ip router

172.16.40.1(ctx-ip)[router]#

2. Set the IP address and network mask for the each IP interface (eth0, for example).

Note For the examples in this guide, a private network (172.16.1) IP address is used.

172.16.40.1(ctx-ip)[router]#interface eth0

172.16.40.1(if-ip)[eth0]#ipaddress 172.16.1.10 255.255.255.0

2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0.

2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.

172.16.1.10(if-ip)[eth0]#

3. Make this modified configuration your new start-up configuration. On the next start-up the system will

initialize itself using the modified configuration.

172.16.1.10 (if-ip)[eth0]#copy running-config startup-config

172.16.1.10 (if-ip)[eth0]#

6SmartNode 4830 Series Quick Start Guide

4.0 Connecting the SmartNode to the LAN

The 4830 Ethernet ports are auto MDX, therefore a straight-through wired cable can be used for host and switch

connections.

Figure 2. Connecting the SmartNode to the network

You can check the connection with the ping command to another host on the local LAN.

172.16.1.99(if-ip)[eth0]#ping <IP Address of the host>

Respectively from the host: ping 172.16.1.99

Note To ping outside your local LAN, you will need to configure the default gateway.

You may now start to configure the SmartNode from scratch using the CLI commands, but we recommend that

you start your configuration from a template.

For a detailed description of the CLI refer to the SmartWare Software Configuration Guide (SCG) available on the

online at: www.patton.com/smartnode.

5.0 Downloading a configuration example,

adapting it to your network, and loading it onto

the SmartNode

Patton provides a collection of configuration templates on the support page at www.patton.com/smart-

node—one of which may be similar enough to your application that you can use it to speed up configuring the

SmartNode. Simply download the configuration note that matches your application to your PC. Adapt the config-

uration as described in the configuration note to your network (remember to modify the IP address) and copy

the modified configuration to a TFTP server. The SmartNode can now load its configuration from this server.

Note If your application is unique and not covered by any of Patton’s configuration templates, you can man-

ually configure the SmartNode instead of loading a configuration file template. In that case, refer to the

SmartNode Series SmartWare Software Configuration Guide for information on configuring the Smart-

Node device.

Network

interface ETH 0

Cross-over cable

SmartNode

Host

Network

interface ETH 0

Straight-through

wired cable SmartNode

Host

Hub

Straight-through

wired cable

Console

oIPGatewayRouter

ToIPIntegratedAccessDevice

SmartNode4524

Link

100M

Activity

0/0

0/1

0/2

0/3

Enet0 VoicePorts

Power

Run

VoIP Link

Link

100M

Activity

Enet 1

Console

oIPGatewayRouter

ToIPIntegratedAccessDevice

SmartNode4524

Link

100M

Activity

0/0

0/1

0/2

0/3

Enet 0 VoicePorts

Power

Run

VoIPLink

Link

100M

Activity

Enet 1

SmartNode 4830 Series Quick Start Guide 7

In this example we assume the TFTP server on the host with the IP address 172.16.1.11 and the configuration

named SN.cfg in the root directory of the TFTP server.

172.16.1.99(if-ip)[eth0]#copy tftp://172.16.1.11/SN.cfg startup-

config

Download...100%

172.16.1.99(if-ip)[eth0]#

After the SmartNode has been rebooted the new startup configuration will be activated.

6.0 Additional Information

For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,

refer to the SN4830 User Manual available online at www.patton.com/manuals/SN4830.pdf and the

SmartWare Software Configuration Guide available online at www.patton.com/smartnode.

A.0 Customer and Technical Support

Toll-Free VoIP support: call sip:suppo[email protected] with a VoIP SIP client

Online support: www.patton.com

E-mail support: s[email protected]—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

When you issue the reload command, the SmartNode will ask if you want to copy

the running configuration to the startup configuration. Since you just downloaded a

configuration file to the startup configuration you must answer this question with

NO. Otherwise, the downloaded configuration will be overwritten and lost!

CAUTION

8SmartNode 4830 Series Quick Start Guide

B.0 Compliance Information

B.1 Compliance

EMC Compliance:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN55024

Safety Compliance:

•

UL60950-1/CSA C22.2 No. 60950-1

•

IEC 60950-1

•

EN 60950-1

PSTN Regulatory Compliance:

•

FCC Part 68

•

CS-03

•

TBR 21

•

TBR 12 & 13 (E1)

•

AS/ACIF S016:2001 (E1)

•

AS/ACIF S043:2005 (DSL Models)

B.2 Radio and TV interference

The SmartNode router generates and uses radio frequency energy, and if not installed and used properly—that

is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television

reception. The SmartNode router have been tested and found to comply with the limits for a Class A computing

device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide rea-

sonable protection from such interference in a commercial installation. However, there is no guarantee that

interference will not occur in a particular installation. If the SmartNode router does cause interference to radio or

television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct

the interference by one or more of the following measures: moving the computing equipment away from the

receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet

(such that the computing equipment and receiver are on different branches).

B.3 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of

this equipment is a label that contains—among other information—a product identifier in the format US:

AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

SmartNode 4830 Series Quick Start Guide 9

The method used to connect this equipment to the premises wiring and telephone network must comply with the

applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that

temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com-

pany will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with

the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens the telephone company will provide advance notice in

order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If

the equipment is causing harm to the telephone network, the telephone company may request that you discon-

nect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-

vice commission or corporation commission for information.

B.4 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con-

firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra-

tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications

were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,

operational and safety requirements. The Department does not guarantee the equipment will operate to the

user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company’s inside wiring associated with a single line individual service

may be extended by means of a certified connector assembly (telephone extension cord). The customer should

be aware that compliance with the above condition may not prevent degradation of service in some situations.

Repairs to some certified equipment should be made by an authorized maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for

their own protection that the ground connections of the power utility, telephone lines and internal metallic water

pipe system, are connected together. This protection may be particularly important in rural areas.

10 SmartNode 4830 Series Quick Start Guide

B.5 CE Notice

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws

of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition

of their conformity.

The safety advice in the documentation accompanying this product shall be obeyed. the conformity to the above

directive is indicated by the CE sign on the device.

B.6 Authorized European Representative

D R M Green

European Compliance Services Limited.

Oakdene House, Oak Road

Watchfield,

Swindon, Wilts SN6 8TD, UK

Autres manuels pour SmartNode 4830 Series

Table des matières

Autres manuels Patton electronics Routeur réseau

Patton electronics

Patton electronics SmartNode 4960 Series Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4960 Series Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 1200 Manuel utilisateur

Patton electronics

Patton electronics ENVIRONET EHA3201 Manuel utilisateur

Patton electronics

Patton electronics SMART NODE 4950-NCE Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4110 Series Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4110 Series Manuel utilisateur

Patton electronics

Patton electronics SMART NODE 4950-NCE Manuel utilisateur

Patton electronics

Patton electronics IpLink 2884 Manuel utilisateur

Patton electronics

Patton electronics OnSite 3210 Series Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4950 Manuel utilisateur

Patton electronics

Patton electronics 3087 Manuel utilisateur

Patton electronics

Patton electronics IPLink 2802 Manuel utilisateur

Patton electronics

Patton electronics SL4020 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4830 Series Manuel utilisateur

Patton electronics

Patton electronics OnSite 2800 Series Manuel utilisateur

Patton electronics

Patton electronics IPLink 2803 Manuel utilisateur

Patton electronics

Patton electronics IM1/I4 Manuel utilisateur

Patton electronics

Patton electronics IPLink 2821 Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4900 Manuel utilisateur

Patton electronics

Patton electronics ONSITE 2603 Manuel utilisateur

Patton electronics

Patton electronics 4630 Series Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4552 Manuel utilisateur

Patton electronics

Patton electronics 3060/V24 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité