Parker DC590+ Manuel utilisateur

POWER CONNECTIONS

BEFORE YOU START

This document covers the steps necessary

for a basic start up of the DC590+DRV drive.

Drive start ups should be performed by

qualified electrical technicians who are

familiar with DC drives and their applica-

tions. For detailed safety, installation, ad-

vanced features and applications on the

590+, refer to the Product Manual.

Ensure that all local electric codes are met

while installing the drive. Check that all live

parts are covered to protect against electric

shock and that unexpected rotation of the

motor will not result in bodily harm or injury.

This document expects that the drive is

already installed in its intended location and

that all relevant installation procedures

have been followed. Please ensure that the

drive has adequate ventilation so that ambi-

ent temperature does not exceed 45°C

(112°F) under normal operating conditions.

To access the bottom layer, slide off the

bottom terminal cover and unfasten the two

retaining screws. Hinge the plastic body

upwards and engage the support bar. • 3-phase supply to L1, L2, L3

• Motor armature to A+, A-

• Motor fields to F+, F-

• Motor thermistor to Th1, Th2

• Control supply to L, N. Check

drive nameplate for correct aux

voltage supply rating

• Blower to BL1, BL2, BL3, if fitted

thermistor

control power

field

armature

3 phase powe

3 phase power

Frame 2 (165A)

CONFIGURE I/O

Under MENU LEVEL\SYSTEM\CONFIGURE I/O, you

may connect and disconnect internal block diagram con-

nections, to use special functions like PID, winder blocks,

diameter block, etc., and to tag analog and digital I/O to

selected points inside the drive to suit your application

needs.

SERIAL LINKS

Under MENU LEVEL\SERIAL LINKS, you may access

parameters related to Techboxes, the system port (P3),

and all the PNO configuration parameters.

SETUP PARAMETERS

Under MENU LEVEL\SETUP PARAMETERS, there are

several submenus where you can enter setup parame-

ters. They are:

Ramps, Auxiliary I/O, Op Station, Jog/Slack, Raise-

Lower, Preset Speeds, Special Blocks, Field Control,

Current Profile, Inverse Time, Stop Rates, Calibration,

Inhibit Alarms, Current Loop, Speed Loop, Standstill,

Setpoint sum 1.

Under MENU LEVEL\PASSWORD, you may enter a

password to protect against unauthorized access to the

drive setup parameters. Refer to the 590+ product manual

for details.

ALARMS & PASSWORD

Under MENU LEVEL\ALARM STATUS, you may view

the active and last alarm status.

ARMATURE AUTOTUNE

• In the configure drive menu, set Autotune to ARM

• On the keypad, press L/R for LOCAL mode

• Ensure that the motor shaft is not allowed to rotate

• Press RUN. Drive will begin autotuning the armature.

• When the drive stops and no error message is dis-

played on the MMI, the autotune was successful.

• Go to MENU LEVEL\SAVE PARAMETERS and save

your settings.

FIELD AUTOTUNE

• In the configure drive menu, set Autotune to FLD

• On the keypad, press L/R for LOCAL mode

• Press RUN. Drive will begin autotuning the field.

• When the drive stops and no error message is dis-

played on the MMI, the autotune was successful.

Parker Hannifin Corporation

SSD Drives Division

9225 Forsyth Park Drive

Charlotte, NC 28273 USA

www.SSDdrives.com

Main (704) 588-3246 Support (704) 602-6062

HA470388U200 Issue 6

DC590+ DRV

Series 2

Quick Start

Frame 2

165 amps

OWER

REFERENCE S EQUENCING

• Speed potentiometer across A1

(low), B3(high), A4(wiper) OR

• External 2-wire speed reference

between A1(-) and A4(+)

• Jumper A6 to B3

• E-Stop relay n.o. contact between B8, C9

• E-Stop relay n.o. TDD contact between B9, C9

• Jumper C1 and C2 if no external trip contact

• Jumper C5 and C9 for internal enable contact

• Start contact between C3 and C9

• Jog contact between C4 and C9

• Health relay coil (24V) between B6(+) and C1(-)

• Armature Voltage is the default speed feedback

mode and does not require a feedback card.

• Four feedback cards are available. Analog Tach,

encoder, acrylic microtach and glass microtach.

• Select the correct feedback card. Install it on the

feedback header, shown by the arrow in the figure.

Ensure all standoffs are securely snapped in place

• On the analog tach card, set switch settings in Units,

Tens and Hundred, corresponding to tachometer

output voltage at maximum speed

• DC Analog Tach: G3(+), G4(-). Set switch to DC

• AC Analog Tach: G1, G2. Set switch to AC

• Encoder: E1=0V, E2=+, E3,E4=A, A, E5,E6=B, B

• Microtach: C1=0V, C9=24V, F1=fiberoptic receive

SPEED FEEDBACK

CALIBRATION

All calibration is done in software, through

the keypad.

ESCAPE ONE LEVEL

ENTER MENU

SCROLL

DOWN

The DC590+ can also be calibrated using the programming tool software.

This is the power-up welcome screen

DIGITAL DC DRIVE

DC 4Q 34A

MENU LEVEL

DIAGNOSTICS

MENU LEVEL

CONFIGURE DRIVE

NOM MOTOR VOLTS

CONFIGURE DRIVE

CONFIGURE ENABLE

ARMATURE CURRENT

FIELD CURRENT

FLD. CTRL MODE

FLD. VOLTS RATIO

MAIN CURR.LIMIT

AUTOTUNE

SPEED FBK SELECT

ENCODER LINES

ENCODER RPM

ENCODER SIGN

SPD. INT TIME

SPD. PROP GAIN

DC 4Q 34A

MENU LEVEL

Press M. You are in MENU LEVEL, at DIAGNOSTICS

Press the M key to get to MENU LEVEL

Up arrow to get to CONFIGURE DRIVE menu

Press M and up arrow to ENABLE drive configuration

All 7 LEDs blink in Configuration mode. Press E when done

Enter rated motor armature current

Toggle between voltage and current modes

Enter desired current limit setting. Usually 100%

Change the polarity of the encoder signal

Speed loop integral gain

Speed loop proportional gain

Using the Up & Down arrows, enter rated motor voltage

Enter rated field current. Skip if field is in Voltage mode

If in voltage mode: Ratio = (field volts/AC supply)*100

Example: For a 300V field and 460V supply: Ratio = 300/460*100 = 65%

Leave this OFF. Autotune after calibration is complete

Choose from Armature Volts/Analog Tach/Encoder

Enter the pulses per rev. rating of the encoder

Enter the max speed here. Corresponds to 100% speed

• Set CONFIGURE ENABLE to DISABLE. The drive will display “CALIBRATING”

• Under MENU LEVEL/PARAMETER SAVE, press the M and UP to save your settings

Autres manuels Parker Entraînement CC

Parker

Parker XLT50-D Manuel utilisateur

Parker

Parker HAS Series Manuel utilisateur

Parker

Parker ac890 Manuel utilisateur

Parker

Parker ac890 Manuel utilisateur

Parker

Parker PDHX-E Series Manuel utilisateur

Parker

Parker LVD1 Manuel utilisateur

Parker

Parker HMR 08 Series Manuel utilisateur

Parker

Parker Hi-drive Manuel utilisateur

Parker

Parker AC30 series Manuel utilisateur

Parker

Parker AC70 Manuel utilisateur

Parker

Parker OSPP-Classic Manuel utilisateur

Parker

Parker Compax3S Manuel utilisateur

Parker

Parker Compax3S Manuel utilisateur

Parker

Parker Compax3 Series Manuel utilisateur

Parker

Parker AC10 series Instructions d'utilisation

Parker

Parker 590+ series Manuel utilisateur

Parker

Parker AC30 series Manuel utilisateur

Parker

Parker 638 series Manuel utilisateur

Parker

Parker GT6-L8-NK Manuel

Parker

Parker AC30 series Manuel d'installation et d'exploitation

Parker

Parker ViX250IM Manuel utilisateur

Parker

Parker AC20F Series Instructions de montage

Parker

Parker 890SD Manuel utilisateur

Parker

Parker Compumotor AX Manuel utilisateur

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

Danfoss

Danfoss VLT 2800 Series Fiche technique

ABB

ABB ACQ580-01 Series Manuel d'installation

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

Siemens

Siemens SINAMICS G Fiche technique

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Mode d'emploi

SOMFY

SOMFY JR RU 30 Manuel utilisateur

Beckhoff

Beckhoff AX8911 Manuel de l'opérateur