Parker AC10 series Instructions d'utilisation

This guide is intended to complement the user manual provided by the manufacturer.

It is provided as a basic introduction to the product for Inverter Drive Supermarket customers.

It should not be used as a replacement for the manual issued by the manufacturer.

Issue 3

20181109

This product is not a safety device. All safety considerations including but not

limited to Emergency Stop provision should be assessed separately and are

outside the scope of this guide.

Parker AC10 Frequency Inverter (to 22kW)

Easy Start Guide

The Parker AC10 Frequency Inverter range is

available to order from inverterdrive.com

1)Do not re-set while the motor is rotating

2)Perform parts replacement after discharge is ﬁnished

3)Do not connect output terminals to the power supply

CAUTION:

L2 P

Easy Start Guide

Page 1

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

Page 5

Page 1

Page 2

Page 3

Page 4

Page 7

Page 8

Page 9

Page 6

Page 10

Page 11

Page 13

Page 14

Page 12

How to Reset the Inverter to Factory Defaults

How to connect and configure a Potentiometer

for remote speed control

Contents

Parameters - Overview

Parameters to set before use

How to connect and configure a Run/Stop switch

with Forward/Reverse selection

Power and Motor Connections (Single Phase)

How to Operate the Inverter from the keypad

How to enable Sensorless Vector mode

How to connect and configure a Run Forward or

Run Reverse switch

How to configure “3-Wire” control with Run/Stop

pushbuttons and Forward/Reverse selection

Power and Motor Connections (Three Phase)

How to set a Parameter value

Brake Resistor Connection

Motor Connections - Star and Delta

Contents

Parker AC10 Series Inverter (to 22kW)

Easy Start Guide

1. Power and Motor Connections (Single Phase)

Page 2

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

This guide has been produced by The Inverter Drive Supermarket Ltd.

Parker AC10 Series Inverter (to 22kW)

The main illustration above is based on the

0.75kW rating (size 1). The supply terminals

for ratings from 1.1kW (size 2) is also shown.

The L3/T terminal (if present) can be ignored.

The order of the three motor phases

determines the initial direction the motor turns.

Notes: Important:

Use screened or armoured cable between the

Inverter and Motor and ensure it is grounded

as shown.

The supply must match the Inverter

specification.

The motor must be separately earthed.

Before commencing, confirm that the Inverter and

all cables are completely isolated from the power

supply, have been isolated for at least 5 minutes

and that the motor is not turning.

MotorSupply

Neutral

Live

Earth

1)Do not re-set while the motor is rotating

2)Perform parts replacement after discharge is ﬁnished

3)Do not connect output terminals to the power supply

CAUTION:

L2 P

Phase

Screen / Armour

Neutral

Live

Earth

L3/T

Size 2

Supply

L2/SL1/R L3/TL2/SL1/R

Easy Start Guide

Page 3

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

This guide has been produced by The Inverter Drive Supermarket Ltd.

Parker AC10 Series Inverter (to 22kW)

2. Power and Motor Connections (Three Phase)

1)Do not re-set while the motor is rotating

2)Perform parts replacement after discharge is ﬁnished

3)Do not connect output terminals to the power supply

CAUTION:

The illustration on the left is based on the 22kW

400V model. The terminal layout for other

ratings is similar.

The order of the three supply phases is not

important. They should be connected to the

terminals marked L1/R, L2/S and L3/T as

shown. In some cases, these terminals may be

marked L1, L2 and L3 only.

Notes:

The order of the three motor phases

determines the initial direction the motor turns.

This can be reversed by physically swapping

any two motor phases. Or by changing the

Inverter parameters.

The motor must be separately earthed.

The supply must match the Inverter

specification.

Use screened or armoured cable between the

Inverter and Motor. To minimise

electromagnetic interference, ensure the

cable screen is grounded as shown.

Before commencing, confirm that the

Inverter and all cables are completely

isolated from the power supply, have

been isolated for at least 5 minutes and

that the motor is not turning.

Motor

Phase

Earth

Phase

Supply

Screen or

Armour

Easy Start Guide

3. Motor Connections - Star and Delta

Page 4

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

The order of the three phases determines the

direction the motor turns.

3.2 Motor connected in DELTA:

The link configuration is shown in the

illustration opposite and is sometimes referred

to as “three-a-breast”.

Note that the manufacturer recommends that

the cable screen is earthed at both ends and

the motor and Inverter are earthed separately.

3.1 Motor connected in STAR (or Wye):

The order of the three phases determines the

direction the motor turns.

Only two links are required for Star. Double-up

the links if changing from Delta to allow the

motor to be changed back in future.

For safety purposes, Star (shown opposite) is

the default configuration for small motors

(usually to 3kW) and is sometimes known as

“two at one side”.

Note that the manufacturer recommends that

the cable screen is earthed at both ends and

the motor and Inverter are earthed separately.

The two ways of connecting the links are

shown below. These are known as “Star” (the

higher voltage) or “Delta” (the lower voltage).

Dual voltage induction motors typically include

terminal boxes with six points. The points can

be connected together with links in one of two

ways to suit one of the two rated voltages.

Delta is represented by a triangle and star by a

Y (Wye).

Dual voltage motor nameplates include

symbols to represent voltage and full load

current in each configuration.

The selection of Star or Delta is not optional

and must match the supply voltage.

Parker AC10 Series Inverter (to 22kW)

Phase

Earth

Screen

Phase

Link DELTA

STAR

Link

Earth

Screen

Easy Start Guide

Page 5

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

4. Parameters - overview

Parameter

Description

How to set

F111

Maximum Frequency (Hz)

Maximum frequency for the Inverter. Default is which suits most applications.50

F112

Minimum Frequency (Hz)

Minimum frequency for the Inverter. Default is which suits most applications.0.5

F114

First Acceleration Time (s)

Default is seconds; increase or decrease if faster or slower acceleration is required.5

F115

First Deceleration Time (s)

Default is seconds; increase or decrease if faster or slower deceleration is required.5

F137

Torque Compensation Mode

Default is ; can be set to 1 for centrifugal fan and pump applications.auto

F153

Carrier Frequency

Setting is rating dependent. Only change if required; default will suit most applications.

F200

Start Command Source

Default is for keypad + terminal + MODBUS (any input source).4

F201

Stop Command Source

Default is for keypad + terminal + MODBUS (any input source).4

F203

(desired motor speed in Hz)

Frequency Command Source

F113 is adjusted by the keypad and stored. No need to change either F113 or F203.

Default is 'Memory' which is set by parameter F113;

F209

Stopping Mode

Default is , ramped stop. Change to 1 for coast stop; this may suit some fan loads.0

F220

Frequency Memory

Default is ; can be set to 1 to store the keypad setpoint (F113) during power down.0

F228

Application Selection

Defaults below are based on F228 = 0

Default is ; will suit most applications. 5 different application Macros available.0

F801

Rated Motor Power (kW)

Rated kW of the motor. Set to match the motor nameplate eg. (2.2kW)2200

F802

Rated Motor Voltage (V)

Rated Voltage of the motor. Set to match the motor nameplate eg V230

F803

Rated Motor Current (A)

Rated current of the motor. Set to match the motor nameplate eg A2.4

F805

Base Motor rpm

Once this is set, read-only parameter F804 (number of motor poles) will be recalculated.

Rated rpm of the motor. Set to match the motor nameplate eg rpm (min-1)1460

F810

Motor rated Freq

Rated frequency of the motor. Default is Hz; change to suit the motor.50

Parameters are typically referred to by code or

number (eg. F803 = Rated Motor Current) with

a description available in the manual.

The Inverter contains a number of settings

which can be changed to tailor it for use in a

wide range of applications. These settings are

known as parameters.

The parameters contain critical information

essential to the correct operation of the

Inverter. Therefore, they should at least be

checked by the user before the Inverter is

operated for the first time.

The parameters listed in section 5 are intended

to provide a starting point to allow for basic

operation of theAC10 Inverter.

5. Parameters to set before use

See section 6 to learn how to set a parameter value.

Set the following parameters to allow the AC10

to control a motor with Run, Stop and Speed

Control from the keypad.

If any of the parameters have been changed

previously, follow the procedure in section 14

to reset the Inverter to Factory Defaults.

5.1 Parameters to check and values to set

Parker AC10 Series Inverter (to 22kW)

Easy Start Guide

6. How to set a Parameter value

Page 6

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

This guide has been produced by The Inverter Drive Supermarket Ltd.

Parker AC10 Series Inverter (to 22kW)

The parameter list is prefixed with “F” as illustrated (left).

With the motor stopped, press the “M” key repeatedly until the

parameter list is shown.

6.1 Press “M” key to access parameters.

Press the “0” (stop) key to select the first (left) digit. This represents

the parameter group (F100, F200, F800 etc.)

Note: In parameter “group” mode, the “DGT” (digit) lamp is not

illuminated.

6.2 Select the required parameter “group”.

Use the up and down keys to select parameter group F800.

6.3 Select the required parameter.

Press the “0" (stop) key to select the last two (right) digits. This

represents the parameters within the group.

Use the up and down keys to select parameter F803 (Rated Motor

Current in Amps). Press the “E” key to edit the parameter value.

Note: In parameter mode, the “DGT” (digit) lamp is illuminated.

The display will show the current parameter value. Use the “0" (stop)

key to select a digit (it will flash when selected). Use the up and

down keys to increase or decrease the value as required. In this

example we will set the value to 2.4.

Press the “E” key to save the new value. The display will return to

the parameter list as illustrated in 6.3 above.

6.4 Change the parameter value and save.

Easy Start Guide

7. How to operate the Inverter from the keypad

Page 7

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

The green key will start the motor. The display will reset to 0.00 and

increase as the motor accelerates. The time taken for the motor to

accelerate to the desired speed (in seconds) is proportional to

parameter F114. The “RUN” indicator will illuminate to indicate that the

motor is running. To change the speed whilst the motor is running, use

the up and down keys.

7.3 Press the green “RUN” key to start the motor.

Note: When running, the “M” key can be used to cycle through

other values such as motor rpm, current (A) and voltage (U).

Parker AC10 Series Inverter (to 22kW)

7.1 Select the speed reference.

Press the “M” key repeatedly until the speed reference is shown - the

“Frq” lamp will illuminate. The default is 50.00 (Hz). All digits will

flash except the currently-selected digit. It is the digit that is not

flashing that can be changed.

Note: Once the value is changed it is saved automatically. There

is no need to “save” the value.

Use the “0" (stop) key to move between digits. Use the up and down

arrow keys to change the value as required.

7.2 Set the desired speed.

The “E” key can be used to return the selection to the right-

most digit.

7.4 Press the red “Stop” key to stop the motor.

The red key will stop the motor. The time taken (in seconds) to stop the

motor is proportional to parameter F115.

Once the motor is stopped, the run lamp will not be illuminated and the

display will return to the flashing setpoint shown in 7.2 (above).

8. How to enable Sensorless Vector mode

Page 8

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

The standard motor control mode of the AC10

Inverter is VxF. This simple mode controls

motor speed by varying Volts and Frequency in

a specific ratio to maintain output torque.

The AC10 can also operate in Sensorless

Vector mode. This can improve motor

performance without requiring a separate

feedback device. Sensorless Vector mode

operates in the same way as VxF but performs

a number of calculations to improve low speed

torque.

For loads that cannot be decoupled from the

motor, a stationary Autotune is possible but

requires parameter F809 to be set manually. A

rotating Autotune is therefore the preferred

option.

To enable sensorless vector control first set the

parameter values specified in 8.1 and then

follow the steps described in 8.2 and 8.3.

These calculations require a rotating

“autotune” run with bare shaft during which the

Inverter operates for approx. 10s to gather the

necessary data.

Parameter

Description

How to set

F801

Rated Motor Power (kW)

Rated kW of the motor. Set to match the motor nameplate eg. (2.2kW)2200

F802

Rated Motor Voltage (V)

Rated Voltage of the motor. Set to match the motor nameplate eg V230

F803

Rated Motor Current (A)

Rated current of the motor. Set to match the motor nameplate eg A2.4

F805

Base Motor rpm

Rated rpm of the motor. Set to match the motor nameplate eg rpm (min-1)1460

Once this is set, read-only parameter F804 (number of motor poles) will be recalculated.

8.1 Parameters to check prior to an Autotune.

Easy Start Guide

Parker AC10 Series Inverter (to 22kW)

Once the parameters in 8.1 have been set, select parameter F800

and press “E” to edit the value. Change the value to 1. The value will

flash. Press “E” again to save. The display will return to F800.

Ensure that the motor is decoupled from the load before pressing the

green “I” (start) button to begin the autotuning process. This will take

approx. 10 seconds during which the “run” lamp will illuminate and

the motor will accelerate and decelerate.

8.2 Start Autotune.

8.3 The Autotune process.

During the autotuning process, the display will show “TEST”.

When the process is complete the motor will stop, the “run” lamp will

no longer be illuminated and the display will return to the speed

reference. The results are saved in parameters F806 to F809 but

sensorless vector mode is not enabled automatically.

Important: To enable sensorless vector mode once the autotune

is complete set parameter F106 to 0.

Easy Start Guide

Page 9

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

9. How to connect and configure a Potentiometer

for remote speed control

Parameter

Description

How to set

F203

Main frequency source X

Default is 0. Set to to enable frequency setpoint via the AI1 (Analogue Input 1).1

9.1 Parameters to change for remote Potentiometer speed control

This provides the benefit of allowing motor

speed to be controlled from a more convenient

location such as a cabinet door (if the AC10 is

cabinet-mounted) or on the machine itself.

If speed control via the integrated keypad is

unsuitable for the application, a remote

Potentiometer can be used instead.

The number of turns depends on the

application. A single turn Potentiometer is

available from The Inverter Drive Supermarket

at InverterDrive.com.

Any potentiometer rated from 2kOhm to

5kOhm can be used - eg. .4.7kOhm

The default output frequency at 0V is the

minimum frequency of the Inverter. To change

this, edit Parameter F112. The default output

frequency at 10V is 50Hz. To change this, edit

Parameter F111.

9.2 Connecting the Potentiometer

First, ensure the Voltage/Current Input switch

“J5" is set to “V” (Voltage). Then, set SW1 to

off/on (down/up) for 0-10V operation.

A wiring diagram is shown in the illustration

opposite. The most important connection at

the Potentiometer end is the centre terminal or

“wiper”. The wiper will output a variable voltage

between 0 and 10 Volts and should be

connected to the “AI1" terminal on the Inverter.

It is this voltage which provides the speed

signal with 0V being slowest and 10V fastest.

If the rotation of the Potentiometer is the

opposite to that required (ie. turn anti-

clockwise to increase speed instead of

clockwise) reverse connections GND and 10V.

Use shielded cable between Potentiometer

and Inverter and ensure that the cable screen

is connected to the Inverter earth terminal only.

Screened

Cable

Parker AC10 Series Inverter (to 22kW)

4.7kOhm

Potentiometer

[Order Code 31350]

Screen to

Earth Terminal

Voltage/Current

Input Switch “J5"

SW1

Autres manuels pour AC10 series

Table des matières

Autres manuels Parker Entraînement CC

Parker

Parker Gemini GT6K Manuel utilisateur

Parker

Parker ac890 Manuel utilisateur

Parker

Parker DC590+ Manuel utilisateur

Parker

Parker HAS Series Manuel utilisateur

Parker

Parker AC20F Series Instructions de montage

Parker

Parker AC30 series Manuel utilisateur

Parker

Parker E-DC Manuel

Parker

Parker Gemini GT6 Series Manuel

Parker

Parker E Series Manuel utilisateur

Parker

Parker PDS Series Manuel utilisateur

Parker

Parker Compax3H C3H1xxV4 Series Manuel utilisateur

Parker

Parker AC30 series Manuel utilisateur

Parker

Parker GT6-L8-NK Manuel

Parker

Parker HMR 08 Series Manuel utilisateur

Parker

Parker Compax3S Manuel utilisateur

Parker

Parker Hi-drive Manuel utilisateur

Parker

Parker PDHX-E Series Manuel utilisateur

Parker

Parker 638 series Manuel utilisateur

Parker

Parker OSPP-Classic Manuel utilisateur

Parker

Parker Compumotor 6000 Series Manuel utilisateur

Parker

Parker AC30 series Manuel d'installation et d'exploitation

Parker

Parker AC70 Manuel utilisateur

Parker

Parker LINKnet AC30P Manuel utilisateur

Parker

Parker ViX250IM Manuel utilisateur

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

Danfoss

Danfoss VLT 2800 Series Fiche technique

ABB

ABB ACQ580-01 Series Manuel d'installation

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

Siemens

Siemens SINAMICS G Fiche technique

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Mode d'emploi

SOMFY

SOMFY JR RU 30 Manuel utilisateur

Beckhoff

Beckhoff AX8911 Manuel de l'opérateur