Parker 890SD Manuel utilisateur

890SD Standalone Drive 5-1

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

Chapter 5 890SD Standalone Drive

This chapter describes the mechanical and electrical installation of the 890SD Standalone Drive. It

discusses configuring your system, and how to turn the motor for the first time.

Follow the steps for a successful installation.

♦Step 1: Mechanical Installation

Mechanical Installation Diagram

Enclosure details

Mounting dimensions

♦Step 2: Connecting power

♦Step 3: Control connections

Control connection diagram

890SD Standalone Drive terminals

♦Step 4: Checking the system

Power-up with 24V DC|

Configure the 890SD Standalone Drive

Set-up parameters

♦Step 5: Run the motor

Powering-up the unit

The Autotune feature

Initial start-up routines

5-2 890SD Standalone Drive

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

Step 1: Mechanical Installation

Install the 890 units and associated equipment into the cubicle. The diagram shows a typical layout using

Star Point earthing for EMC compliance. Refer to Appendix C for further information.

KEY

A Analog Clean

Earth

B Back plate

C Cubicle

E Dirty Earth

F Filter (optional)

G Star Point Earth

P Fuse or

circuit breaker

R AC Line Reactor

(optional)

S Signal/Control

Screen Earth

T 24V Power Supply

(optional)

Figure 5.1 A Typical Cubicle Layout (wiring not shown)

890SD Standalone Drive 5-3

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

Main Points

♦This is a cubicle-mounted unit. It is not suitable for wall-mounting.

♦Mount 890's side-by-side vertically on a solid, flat, normally cool, non-flammable, vertical surface.

♦The unit(s) can be DIN rail or panel mounted.

♦Fit the 890 Installation kit to the bottom of the drive.

♦Adequate ventilation must be provided.

♦Avoid excessive vibration.

♦The earth points (D, E, G, M & S) are shown separated - it may be possible to use one large star point

without EMC problems, this will depend upon your application.

Note Refer to Appendix C for information about EMC compliance.

Sizing the Enclosure

The enclosure should comply with the European safety standards VDE 0160/EN50178 and will require a

tool for opening.

The size of the enclosure will depend on many factors:

♦Physical size and number of units

♦Ventilation clearances

♦Power output, affected by derating due to altitude and ambient temperature

5-4 890SD Standalone Drive

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

Enclosure/Environmental Information

The information here will help you to specify the enclosure to house the 890(s).

890 Operating Conditions

Operating Temperature 0°C to 45°C (32°F to 113°F)

Product Enclosure Rating IP20 - UL (c-UL) Open Type (North America/Canada) Type 1

Suitable for cubicle mount only

Cubicle Installation The 890 must be installed to EN60204 Standard in the cubicle. For

USA, the cubicle shall meet the requirements of UL50.

Cubicle to provide the following attenuation to radiated emissions:

EMC Enclosure Standard

Attenuation to RF in

spectrum 30-1000MHz

EN61800-3

Category C3 NONE

EN61800-3

Category C2 Restricted Distribution

EN61000-6-3:2001

10db

Cubicle Rating

EN61800-3

Category C1 Unrestricted Distribution

EN61000-6-4:2001

20db

890SD Standalone Drive 5-5

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

890 Operating Conditions

Humidity Maximum 85% relative humidity at 40°C (104°F) non-condensing

Atmosphere Non flammable, non corrosive and dust free

Climatic Conditions Class 3k3, as defined by EN50178.

Vibration The product has been tested to the following specification:

Test Fc of EN60068-2-6

10Hz<=f<=57Hz sinusoidal 0.075mm amplitude

57Hz<=f<=150Hz sinusoidal 1g

10 sweep cycles per axis on each of three mutually perpendicular axis

Safety

Pollution Degree

Pollution Degree ll (non-conductive pollution, except for temporary

condensation)

Europe

When fitted inside an enclosure, this product conforms with the Low

Voltage Directive 2006/95/EC using EN50178 to show compliance.

North America/ Canada

Complies with the requirements of UL508C as an open-type drive.

Conformal Coated

Product

Conformal coating increases the product’s resistance to certain

climatic conditions.

Note conformal coating, where effective, will only mitigate the effects

being considered.

5-6 890SD Standalone Drive

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

Cooling

Units are designed for mounting side-by-side as shown. A minimum of 150mm (6") free-air space must be

allowed at the top and bottom of each unit.

The 890 gives off heat in normal operation. The mounting surface for the unit should be normally cool.

Allow a free flow of air through the top and bottom ventilation slots and heatsink. Remember that any other

equipment may have its own clearance requirements. If you mount 890s above and below each other, the

minimum top and bottom clearances should be added to produce an overall clearance value.

150mm

890SD Standalone Drive 5-7

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

Mounting Dimensions

Mount the unit using the keyholes and slots, or fix to a DIN rail (35mm DIN).

Side view Front view

Dimensions are in millimetres. X: Power Bracket - 890 Installation Kit

890SD Weight Frame B 5kg/11.0lbs Frame C 6.6kg/14.5lbs Frame D 12.1kg/26.7lbs

5-8 890SD Standalone Drive

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

The 890 Installation Kit is supplied with your unit. The kit provides several options for earth/ground

connections. It also includes the brackets for DIN rail mounting the unit. Refer to the

instructions in the kit and use the appropriate parts.

Cables are considered to be electrically sensitive, clean or noisy. Plan your cable routes to

segregate these cables for EMC compliance. Refer to Appendix C: "Certification".

Panel Mount Fixings

Support the unit at the top and bottom with fixings to secure the unit to the panel. Mark

and drill the fixing holes into the panel. Refer to the fixing centres given on the previous

page. Insert the fixings into the top hole(s) and hang the unit. Insert the bottom fixing(s)

and tighten to the required torque.

DIN Rail Mounting

The unit can be DIN rail mounted (35mm DIN).

Convert the unit to accept to DIN rail mounting:

1. Secure the DIN clips from the 890 Installation Kit into the threaded inserts at the top of

the unit using the fixings supplied.

2. Hang the unit on the top DIN rail. Fix the DIN clips onto the bottom of the unit and clip

onto the DIN rail.

3. Tighten both the top and bottom clips when the unit is in position on the rail.

Shield Bonding Clips

Fit the shield bonding clips to the Control Bracket/Power Bracket. Select slots providing a

loose fit. This will then allow the clips to be tightened by hand.

Note Do not squeeze the clip sides to produce a fit as this will crimp the sides to the clip's

moving soleplate.

890SD Standalone Drive 5-9

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

890 Installation Kit

The fitting instructions for the kit are reproduced below.

5-10 890SD Standalone Drive

890CS Common Bus Supply - Frames B & D; 890CD Common Bus Drive and 890SD Standalone Drive - Frames B, C & D

Step 2: Connecting Power

In this section we are going to connect the 3-phase supply to the 890SD Standalone Drive(s).

We'll also connect the motor and the (optional) brake resistor.

WARNING

During commissioning, remove the fuses (or trip the circuit breaker) on your 3-phase supply.

Make sure the power is OFF, and that it cannot be switched on accidentally whilst you are working.

Solid-State Short-Circuit Protection

These devices provide Class 10 motor overload protection. The maximum internal overload protection level

(current limit) is 150% for 60 seconds in Constant mode. Refer to Appendix D: Programming - CURRENT

LIMIT for user current limit adjustment information.

An external motor overload protective device must be provided by the installer where the motor has a full-

load Ampere rating of less than 50% of the drive output rating; or when the MOTOR STALLED trip is

TRUE (TRIPS STATUS::DISABLED WORD 1>>MOTOR STALLED); or when the STALL TIME

parameter is increased above 480 seconds.

Refer to the 890 Installation Kit for earth/ground fixing details. Fit the appropriate parts.

Each unit must be permanently earthed according to EN 50178.

For permanent earthing:

A cross-section conductor of at least 10mm² is required. This can be achieved either by using a

single conductor (PE) or by laying a second conductor though separate terminals (PE2 where

provided) and electrically in parallel.

Autres manuels pour 890SD

Table des matières

Autres manuels Parker Entraînement CC

Parker

Parker AC30 series Manuel d'installation et d'exploitation

Parker

Parker AC20 Series Instructions de montage

Parker

Parker ac890 Manuel utilisateur

Parker

Parker AC20F Series Instructions de montage

Parker

Parker 590+ series Manuel utilisateur

Parker

Parker PSD04 Manuel utilisateur

Parker

Parker Compumotor ZETA6104 Manuel utilisateur

Parker

Parker PDS Series Manuel utilisateur

Parker

Parker Gemini GT6 Series Manuel

Parker

Parker Compumotor Manuel utilisateur

Parker

Parker Compax3H C3H1xxV4 Series Manuel utilisateur

Parker

Parker 590+ DRV Manuel utilisateur

Parker

Parker AC10 series Instructions d'utilisation

Parker

Parker 890CS Manuel utilisateur

Parker

Parker Compumotor AX Manuel utilisateur

Parker

Parker DC590+ Manuel utilisateur

Parker

Parker AC30 series Manuel utilisateur

Parker

Parker AC30 series Manuel utilisateur

Parker

Parker GT6-L8-NK Manuel

Parker

Parker Hi-drive Manuel utilisateur

Parker

Parker ac890 Manuel utilisateur

Parker

Parker AC15 Series Instructions de montage

Parker

Parker E-DC Manuel utilisateur

Parker

Parker E-DC Manuel

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

Danfoss

Danfoss VLT 2800 Series Fiche technique

ABB

ABB ACQ580-01 Series Manuel d'installation

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

Siemens

Siemens SINAMICS G Fiche technique

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Mode d'emploi

SOMFY

SOMFY JR RU 30 Manuel utilisateur

Beckhoff

Beckhoff AX8911 Manuel de l'opérateur