Parker RL Series Caractéristiques techniques

Maintenance

Instructions

MI-137 Revision A

Parker Hannifin Corporation

Instrumentation Valve Division

Jacksonville, Alabama

RL Series Relief Valve

Figure 1: RL Series

Relief Valve Cross

Sectional View

Figure 2: RL Series

Relief Valve with

Manual Overrride

Cross Sectional View

Spring Acquisition

The valve is shipped asse bled co plete less the adjust ent cap and the lock nut. Springs can be acquired by

ordering the appropriate kit. Spring kits are as follows:

Spring Pressure Range Kit Name Color Code

10-25 psi KIT-RL4SP-0-25 Magenta

25- 50 psi KIT-RL4SP-25-50 Brown

50-100 psi KIT-RL4SP-50-100 Purple

100-150 psi KIT-RL4SP-100-150 Dark Green

150-225 psi KIT-RL4SP-150-225 Dark Blue

225-400 psi KIT-RL4SP-225-400 White

10-225 psi KIT-RL4SP-10-225 None

Each kit includes a Spring, two (2) PTFE washers, a label, locking wire, and a lead tie down disk.

Parker Hannifin Corporation

Instrumentation Valve Division

Jacksonville, Alabama

MI-137

DISASSEMBLY

WARNING: MAKE CERTAIN T E SYSTEM IN W IC T E VALVE IS INSTALLED IS DRAINED AND/OR EX AUSTED

OF ALL PRESSURES BEFORE VALVE DISASSEMBLY OR REMOVAL OCCURS.

1. If the valve is locked into position, break apart the Locknut and Cap by turning the Locknut clockwise with a 7/8

inch wrench while holding the Cap with another 7/8 inch wrench.

2. If the valve is a anual version, loosen the Set Screw in the Handle by using a 5/64 hex Allen wrench and unthread

the Handle fro the Manual Upper Ste by holding the ste and rotating the Handle counter-clockwise.

3. Unthread the Cap fro the Bonnet by rotating the Cap counter-clockwise.

4. Re ove the Spring and PTFE Washers and set the aside for reuse during reasse bly. (It is possibly easier to

re ove the lower PTFE washer after step 5.)

5. Re ove the Bonnet fro the Valve Body by turning counter-clockwise with a 7/8 inch wrench.

6. Using a pair of pliers, secure a grip onto the Upper Ste /Manual Upper Ste and pull the cartridge asse bly fro

the Valve Body.

7. Disengage the Upper Ste /Manual Upper Ste and the Lower Ste by holding the Lower Ste with a pair of

adjustable pliers (Do not cla p over the cri ped o-ring if the ste is to be reused.) and unthreading the Upper

Ste /Manual Upper Ste with a 7/16 inch wrench.

8. Re ove the Lower Ste fro the Body Bonnet by grasping the end that includes the cri ped seat and gently pull

it out.

O-RING/BACK-UP RING INSERTION

1. Place the andrel over the appropriate end of the co ponents as seen in the drawing.

2. Slide the O-ring or O-ring/Back-up ring co bination slowly and gently over the andrel (Note the orientation of the

O-ring and back-up ring).

3. Place the O-ring or O-ring/Back-up ring into the groove provided for it.

Gently slide the o-ring over the andrel in this direction

Lower Ste Asse bly

Body Bonnet Asse bly

Parker Hannifin Corporation

Instrumentation Valve Division

Jacksonville, Alabama

MI-137

Figure 4: RL Series Relief Valve with Manual Override Exploded View

Setting Desired Cracking Pressure

1. Rotate the Cap to set the desired cracking pressure.

2. Tighten the Lock Nut against the Cap.

f required, secure the pressure setting by using the Lockwire to fasten the Cap and Valve Body together.

REASSEMBLY

MAKE CERTAIN T AT ALL PARTS ARE FREE OF DIRT OR OT ER CONTAMINANTS BEFORE REASSEMBLY.

1. Place the Teflon coated O-ring onto the Lower Ste and the O-ring and Back-up ring onto the Body Bonnet as

shown in the section titled O-Ring/Back-up Ring Insertion .

2. Insert the Lower Ste into the Body Bonnet being careful not to da age the O-ring or Back-up Ring.

3. Thread the Upper Ste / Manual Upper Ste onto the Lower Ste and torque to 12 in-lbs by gripping the Lower

Ste with a pair of pliers and rotating the Upper Ste clockwise with a 7/16 inch hex socket torque wrench. (Do

not cla p over the cri ped portion of the Lower Ste .)

4. Insert the asse bly fro 4 into the Valve Body being careful not to da age the O-ring and Back-up Ring.

5. Apply a liberal a ount of lubricant, as consistent with the Valves service require ents, onto the body ste end

threads.

6. Install the Bonnet onto the Valve Body and torque to 30 ft-lbs by turning clockwise with a 7/8 inch hex socket

torque wrench.

7. Place a PTFE Washer into the bore of the Bonnet, insure that the washer is lying flat against the face of the Upper

Ste /Manual Upper Ste .

8. Place the Spring into the bore of the Bonnet.

9. Place the other PTFE Washer onto the top of the Spring.

10. Place an appropriate lubricant, consistent with the valves service require ents, on the internal threads of the Cap.

11. Thread the Cap onto the Bonnet. Insure that the washer re ains atop the Spring during thread engage ent.

12. If your syste de ands, lock the Cap in place by holding it with a 7/8 inch wrench and turning the Locknut counter-

clockwise until it is snug against the Cap.

13. If the valve has a Manual Upper Ste , thread the Handle onto it.

INI-237

Parker Hannifin Corporation

Instrumentation Valve Division

Jacksonville, Alabama

VALVE CONNECTO MAKE-UP INST UCTIONS

MALE AND FEMALE PIPE PORTS

Wrench flats are provided on the Valve Body. It is recommended a smooth- jawed wrench or vise be used to grip the Valve Body.

1. On the male threaded part of the connection apply a high quality pipe joint compound or PTFE tape made for this purpose. When PTFE tape is

used it is recommended two full turns of tape be applied. PTFE tape should not be overhanging or covering the first thread

2. Engage the Valve and the other component part together until hand-tight.

3. With a proper wrench holding both the Valve and the component part continue to tighten to achieve a leak-tight joint.

ULTRASEAL CONNECTIONS

1. Insert the proper O-Ring into the UltraSeal fittings O-Ring groove. Position the UltraSeal gland sealing face against the O-Ring and then advance

the Nut to a finger-tight position.

2. A positive seal is obtained by advancing the Nut no less than 1/4 turn from the finger-tight position. Proper UltraSeal make-up is achieved when

a sharp rise in required application torque occurs which indicates proper seal face contact and O-Ring seal compression into the UltraSeal

groove.

VACUSEAL CONNECTIONS

1. A positive seal is obtained by advancing the Nut 1/8 turn from the finger-tight position.

2. A new gasket should be installed upon each fitting re-make to insure system pressure integrity.

TUBE FITTING CONNECTIONS

1. Insert the tube into the Valve port until the tube bottoms out in the Valve Body. Care should be exercised to insure the tube is properly aligned with

the Valve Body and port.

2. Normal make-up for US Customary port sizes 1 thru 3 (1/16 thru 3/16 inch) and SI port sizes 2 thru 4 (2 thru 4 mm) is 3/4 turn from finger tight.

Normal make-up for US Customary port sizes 4 thru 16 (1/4 thru 1 inch) and SI port sizes 5 thru 25 (5 thru 25 mm) is 1 1/4 turn from finger tight.

For larger port sizes consult Parker Ferrule Presetting Tool Instructions.

PLEASE FOLLOW THE ABOVE DIRECTIONS FOR COUNTING THE NUMBER OF TURNS FOR PROPER FITTING MAKE-UP. DO

NOT MAKE-UP TUBE FITTINGS BY TORQUE OR FEEL. VARIABLES SUCH AS TUBING AND FITTING TOLERANCES, TUBE

WALL THICKNESS, AND THE LUBRICITY OF NUT LUBRICANTS CAN RESULT IN AN IMPROPERLY ASSEMBLED TUBE FITTING

CONNECTION.

A -Two ferrule A-LOK ®

compression port

M -ANSI/ASME B1.2 .1

External pipe threads

Z -Single ferrule CPITM

compression port

Q -UltraSeal face

seal port

F -ANSI/ASME B1.2 .1

Internal pipe threads

V -VacuSeal face

seal port

Parker Hannifin Corporation

Instrumentation Valve Division

2651 Alabama Highway 21 North

Jacksonville AL 36265-9681

USA

Phone: (256) 435-2130

Fax: (256) 435-7718

www.parker.com/IVD

MI-137 Revision A

WARNING

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF T E PRODUCTS AND/OR SYSTEMS DESCRIBED

EREIN OR RELATED ITEMS CAN CAUSE DEAT , PERSONAL INJURY AND PROPERTY DAMAGE.

This docu ent and other infor ation fro Parker Hannifin Corporation, its subsidiaries and authorized distributors

provide product and/or syste options for further investigation by users having technical expertise. It is i portant that

you analyze all aspects of your application and review the infor ation concerning the product or syste in the current

product catalog. Due to the variety of operating conditions and applications for these products or syste s, the user,

through its own analysis and testing, is solely responsible for aking the final selection of the products and syste s

and assuring that all perfor ance, safety and warning require ents of the application are et.

The products described herein, including without li itation, product features, specifications, designs, availability and

pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any ti e without notice.

ALL PARKER VALVES MUST PASS A RIGID OPERATIONAL AND LEAKAGE TEST BEFORE LEAVING T E FAC-

TORY. IT IS RECOMMENDED AFTER ANY REASSEMBLY, T E VALVE S OULD BE TESTED BY T E USER FOR

OPERATION AND LEAKAGE. IF T ESE INSTRUCTIONS ARE NOT FULLY COMPLIED WIT , T E REPAIRED

PRODUCT MAY FAIL AND CAUSE DAMAGE TO PROPERTY OR INJURY TO PERSONS. PARKER ANNIFIN

CANNOT ASSUME RESPONSIBILITY FOR PERFORMANCE OF A CUSTOMER SERVICED VALVE.

Autres manuels Parker Unité de contrôle

Parker

Parker VA01 Series Manuel utilisateur

Parker

Parker CK-2W Manuel utilisateur

Parker

Parker D31FBxEE Series Manuel utilisateur

Parker

Parker PSSNACM12A Instructions d'installation et d'entretien

Parker

Parker DN80 Manuel utilisateur

Parker

Parker D41FE Manuel utilisateur

Parker

Parker PEV Manuel de service

Parker

Parker PSSTACM12A Instructions d'installation et d'entretien

Parker

Parker S4AD Manuel utilisateur

Parker

Parker PA Series Instructions de montage

Parker

Parker 2B4 Series Manuel utilisateur

Parker

Parker D31DW*EE Series Manuel utilisateur

Parker

Parker C2 Series Instructions d'installation et d'entretien

Parker

Parker DFB Series Manuel utilisateur

Parker

Parker C10 Manuel utilisateur

Parker

Parker D1VW -SC Series Manuel utilisateur

Parker

Parker TPQ Series Manuel utilisateur

Parker

Parker Hi-Pro Manifold Manuel utilisateur

Parker

Parker D*1VW*EE Series Manuel utilisateur

Parker

Parker P33 Guide de configuration rapide

Parker

Parker PID00A-40 Series Manuel utilisateur

Parker

Parker HASV08R Manuel utilisateur

Parker

Parker D Series Manuel utilisateur

Parker

Parker Sporlan SD-114 Guide de l'utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur