Paradyne MIM-10/100 Manuel utilisateur

MIM1-A2-GZ40-00 October 2004 1

MIM-10/100

Installation Instructions

Document Number MIM1-A2-GZ40-00

October 2004

Contents

Software and Firmware License Agreement ...................................................... 1

Product Documentation Online .......................................................................... 3

Unpacking and Inspecting the Equipment ......................................................... 3

Installing the MIM-10/100 .................................................................................. 3

Connecting the Ethernet Cable .......................................................................... 4

LED Indicators ................................................................................................... 5

Regulatory Notices ............................................................................................ 5

Warranty, Sales, Service, and Training Information ........................................... 6

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply

to the software and/or firmware (individually or collectively the “Software”)

incorporated into the Paradyne product (the “Product”) purchased by you and any

derivatives obtained from the Software, including any copy of either. If you have

executed a separate written agreement covering the Software supplied to you

under this purchase, such separate written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to

accept a personal, non-transferable, non-exclusive, right (without the right to

sublicense) to use the Software, solely as it is intended and solely as incorporated

in the Product purchased from Paradyne or its authorized distributor or reseller

under the following terms and conditions:

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

2October 2004 MIM1-A2-GZ40-00

1. Ownership: The Software is the sole property of Paradyne and/or its licensors.

The Licensee acquires no title, right or interest in the Software other than the

license granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in

which the Product was rightfully purchased except upon prior written notice to

Paradyne and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the

Software in whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

5. Except for the Product warranty contained in the manual, the Software is

provided “AS IS” and in its present state and condition and Paradyne makes

no other warranty whatsoever with respect to the Product purchased by you.

THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES,

WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING

WITHOUT LIMITATION:

a. Any warranty that the Software is error-free, will operate uninterrupted in

your operating environment, or is compatible with any equipment or

software configurations; and

b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT

LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied

warranties on limitations on how long an implied warranty lasts, so the above

limitations may not apply to you. This warranty gives you specific legal rights,

and you may also have other rights which vary from one state or jurisdiction to

another.

6. In no event will Paradyne be liable to Licensee for any consequential,

incidental, punitive or special damages, including any lost profits or lost

savings, loss of business information or business interruption or other

pecuniary loss arising out of the use or inability to use the Software, whether

based on contract, tort, warranty or other legal or equitable grounds, even if

Paradyne has been advised of the possibility of such damages, or for any

claim by any third party.

7. The rights granted under this Agreement may not be assigned, sublicensed or

otherwise transferred by the Licensee to any third party without the prior

written consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be

terminated in the event of breach by the Licensee of any provisions of this

Agreement.

9. Upon such termination, the Licensee shall refrain from any further use of the

Software and destroy the original and all copies of the Software in the

possession of Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without

regard to its provisions concerning conflicts of laws.

MIM1-A2-GZ40-00 October 2004 3

Product Documentation Online

Complete documentation for Paradyne products is available at

www.paradyne.com. Select Support →Technical Manuals.

To order a paper copy of a Paradyne document, or to speak with a sales representative,

please call 1-727-530-2000.

Unpacking and Inspecting the Equipment

HANDLING PRECAUTIONS FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage

due to electrostatic discharge (ESD) during normal operation. When

performing installation procedures, however, take proper static control

precautions to prevent damage to equipment. If you are not sure of the

proper static control precautions, contact your nearest sales or service

representative.

If there is any visible damage, do not attempt to install the MIM-10/100; contact

your sales representative.

Installing the MIM-10/100

The MIM-10/100 Micro Interface Module provides additional uplink ports for the

AµD8000 ADSL Micro DSLAM or BSX8000-5 Broadband Services Switch.

NOTE: All MIMs are hot swappable, although removal of a MIM disengages the

upstream network connection for the DSLAM.

Procedure

1. Using a flat-head screwdriver to loosen the fastening screws, remove the

cover plate from the MIM port on the front of your AµD8000 or BSX8000.

CAUTION: The cover plate should be stored for possible future use: if the MIM

is removed from your AµD8000 or BSX8000, it must be replaced with either

another MIM or a cover plate. Do not operate an AµD8000 or BSX8000 with

an open MIM port.

2. Align the MIM-10/100 with the module guides inside the MIM port.

3. Slide the MIM-10/100 firmly into place. Do not use excessive force.

4. Secure the MIM-10/100 by tightening the fastening screws on the MIM

faceplate with a flat-head screwdriver.

4October 2004 MIM1-A2-GZ40-00

Connecting the Ethernet Cable

The Ethernet port is 10/100 auto-negotiating. Set your hub or switch to

auto-negotiate (if applicable) before making the Ethernet connection.

For most applications, the MIM-10/100 connects to a router or a PC using a

straight-through Ethernet cable and to a hub or a switch using a crossover

Ethernet cable. If you are in doubt, verify the pinouts of the device you are

connecting to.

Procedure

1. If a ferrite choke is supplied with your MIM:

— Open the ferrite choke.

— Place the choke around your Ethernet cable as close as possible to the

RJ45 connector.

— Snap shut the ferrite choke. Use a cable tie to hold it in place if it does not

fit tightly on the cable.

2. Plug the Ethernet cable into the Ethernet RJ45 port on the MIM faceplate.

3. Verify the connection; solid illumination of the Lnk LED on the MIM faceplate

indicates an Ethernet link has been established. If the Lnk LED is illuminated

but not the 100 LED, then a 10 Mbps link has been established. If the 100 LED

is also illuminated, then a 100 Mbps link has been established.

Ethernet RJ45 Port Pinouts

00-16917

Ferrite Choke

Plastic

Latch

Connector

Pin Function

Pin 1 Rx+

Pin 2 Rx-

Pin 3 Tx+

Pin 4 not used

Pin 5 not used

Pin 6 Tx-

Pin 7 not used

Pin 8 not used

MIM1-A2-GZ40-00 October 2004 5

LED Indicators

Regulatory Notices

UNITED STATES – EMI NOTICE:

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the

requirements that no modifications will be made to the equipment

unless the changes or modifications are expressly approved by

Paradyne Corporation.

Table 1. LEDs

LED STATE INDICATION ADDITIONAL INFORMATION

100 Solid Green Fast Ethernet connection

(100 Mbps) is established.

If the 100 LED is illuminated, the Lnk LED

will also be illuminated.

No Illumination No Fast Ethernet

connection.

If the 100 LED remains unlit but the Lnk

LED is illuminated then a link has been

established at 10 Mbps rather than 100

Mbps.

Act Flashing Amber Ethernet activity. Traffic is flowing without any problems.

Solid Amber Heavy traffic.

No Illumination No Ethernet activity. Either there is no Ethernet link or a link

exists but there is no activity.

Lnk Solid Green Ethernet connection is

established.

If the Lnk LED is illuminated but not the

100 LED then a 10 Mbps link has been

established. If the 100 LED is also

illuminated, then a 100 Mbps link has

been established.

No Illumination No Ethernet connection. The 100 and Act LEDs will remain unlit by

default.

6October 2004 MIM1-A2-GZ40-00

CANADA – EMI NOTICE:

This Class A digital apparatus meets all requirements of the Canadian

interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du

règlement sur le matérial brouilleur du Canada.

EUROPEAN REGULATORY COMPLIANCE

The following regulatory compliance information applies to the

MIM-10/100 as installed in the AµD8000 or BSX8000-5:

This Class A product complies with European Norm EN55022.

Warning: In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate

measures to correct the situation.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor

directly for any help needed. For additional information concerning warranty, sales,

service, repair, installation, documentation, training, distributor locations, or

Paradyne worldwide office locations, use one of the following methods:

Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.

(Be sure to register your warranty at www.paradyne.com/warranty.)

Telephone: Call our automated system to receive current information by fax or

to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

!!.

*MIM1-A2-GZ40-00*

Table des matières

Autres manuels Paradyne Matériel réseau

Paradyne

Paradyne 8310 MVLt Manuel utilisateur

Paradyne

Paradyne COMSPHERE 3610 Manuel utilisateur

Paradyne

Paradyne COMSPHERE 3810 Manuel utilisateur

Paradyne

Paradyne 7112 Manuel utilisateur

Paradyne

Paradyne Fan Tray 8820-S2-900 Manuel utilisateur

Paradyne

Paradyne DC Power Entry Module 8820-S1-906 Manuel utilisateur

Paradyne

Paradyne MCC Manuel utilisateur

Paradyne

Paradyne FrameSaver NP 100 Manuel utilisateur

Paradyne

Paradyne 3163 Manuel utilisateur

Paradyne

Paradyne Hotwire 5620 Manuel utilisateur

Paradyne

Paradyne Hotwire 5620 Manuel utilisateur

Paradyne

Paradyne Hotwire 5620 Manuel utilisateur

Paradyne

Paradyne Hotwire 7996 Instructions d'utilisation d'origine

Paradyne

Paradyne MIM-4E1 Manuel utilisateur

Paradyne

Paradyne Dual DSU 7511 Manuel utilisateur

Paradyne

Paradyne COMSPHERE 3550 Series Manuel utilisateur

Paradyne

Paradyne COMSPHERE 3610 Manuel utilisateur

Paradyne

Paradyne COMSPHERE 3610 Manuel d'exploitation et d'entretien

Paradyne

Paradyne 4300 Manuel utilisateur

Paradyne

Paradyne 7915-A1 E1 SDSL Manuel utilisateur

Paradyne

Paradyne 3163 Manuel utilisateur

Paradyne

Paradyne COMSPHERE 6700 Series Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 Manuel utilisateur

Paradyne

Paradyne COMSPHERE 3550 Series Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur