Paradox MG-RCV3 Manuel utilisateur

Wireless Expansion Module V1.0

Reference & Installation Manual

MG-RCV3

(DGP-848 / DGP-NE96)

MGRCV3SD_EI01.fm Page -3 Thursday, May 5, 2005 2:22 PM

MGRCV3SD_EI01.fm Page -2 Thursday, May 5, 2005 2:22 PM

Table of Contents

Introduction ...............................................................................................1

Technical Specifications .................................................................................... 1

System Features ............................................................................................... 2

Installation .................................................................................................2

Location ............................................................................................................. 2

Noise Level Test ................................................................................................ 3

Connections and Mounting ................................................................................ 3

Programming a Wireless Fire Zone with a Spectra System................................. 4

About Programming .................................................................................7

Spectra Programming ....................................................................................... 8

Digiplex Series Programming ............................................................................ 8

Transmitter Programming .......................................................................8

Assign the Transmitters to the MG-RCV3 ......................................................... 9

Delete the Assigned Transmitters ...................................................................... 10

Display Options ......................................................................................11

View a Transmitter’s Unknown Serial Number ................................................ 11

View a Transmitter’s Signal Strength .............................................................. 12

Signal Strength Keypad Beep Tones (Spectra only).......................................... 13

View Transmitter’s Current Battery Life (Digiplex Series only) ........................ 13

View Transmitter’s Previous Battery Life (Digiplex Series only) ...................... 14

Supervision Options ..............................................................................15

Low Battery Supervision .................................................................................. 15

Check-In Supervision ...................................................................................... 16

Check-in Supervision Time Interval.................................................................... 16

Tamper Supervision ........................................................................................ 17

On-Board Module Tamper Supervision Zone Assignment (Spectra only).......... 18

On-Board Module Tamper Supervision (Digiplex Series only)........................... 19

Ignore Wireless Transmitter Tamper Signal .................................................... 19

MGRCV3SD_EI01.fm Page -1 Thursday, May 5, 2005 2:22 PM

Programmable Outputs (PGMs) ........................................................... 20

PGM Connection ..............................................................................................20

PGM Activation ................................................................................................20

PGM Deactivation ............................................................................................20

Remote Control Programming ............................................................. 21

Assign a Remote Control to the Magellan Module ...........................................22

View the Assigned Remote Controls (Digiplex Series only)............................... 23

Delete an Assigned Remote Control.................................................................. 24

Assign a Remote Control to a User .................................................................25

Program the Remote Control Buttons ..............................................................26

Hexadecimal Values and Indicators................................................................... 31

Delete Remote Control Button Programming..................................................... 33

System Reset ......................................................................................... 33

Programming Sections (Spectra) ......................................................... 34

Programming Sections (Digiplex Series) ............................................ 35

List of Tables

Interrelated Spectra Transmitter (Tx) Sections.................................................. 8

Interrelated Digiplex Series Transmitter (Tx) Sections ...................................... 9

Interrelated Spectra Remote Control (RC) Sections........................................ 22

Interrelated Digiplex Series Remote Control (RC) Sections............................ 22

Remote Control Button Programming.............................................................. 28

Remote Control Button Options....................................................................... 30

Spectra Hexadecimal Values & Indicators....................................................... 32

Digiplex Series Hexadecimal Values & Indicators........................................... 32

List of Figures

Mounting............................................................................................................ 5

Connecting Magellan to the Control Panel ........................................................ 6

Remote Control Button Programming Example............................................... 30

Remote Control Button Identification............................................................... 30

MGRCV3SD_EI01.fm Page 0 Thursday, May 5, 2005 2:22 PM

Magellan Wireless Expansion Module 1

1.0 Introduction

This manual details how to connect, program and operate the Magellan wireless

expansion module (MG-RCV3) when used in conjunction with a Spectra or a

Digiplex series (DGP-848 or DGP-NE96) security system.

The MG-RCV3 is available in either a 433MHz or 868MHz version. When connected

to a Spectra system, the MG-RCV3 allows you to add up to eight Magellan wireless

transmitters, and up to eight fully programmable Magellan remote controls. When

connected to a Digiplex series system, the MG-RCV3 allows you to add up to 16

Magellan wireless transmitters, and up to 16 fully programmable Magellan remote

controls.

The MG-RCV3 cannot be connected to the Spectra 1727 and 1759MG

control panels.

1.1 Technical Specifications

• Di-pole antenna

• Error Correction Algorithm

• Compatibility: Spectra 1728 and 1738 control panels

Any Digiplex series control panel

Any Magellan wireless transmitter

• Frequency: 433MHz or 868MHz

• Sensitivity: -120 dBm

• Current consumption: 50 mA

• Dimensions (no antenna): 15cm H x 16cm L x 3cm W

(6in H x 6.5in L x 1.1in W)

• Operating temperature: 0°C to 49°C (32°F to 120°F)

• PGM outputs: 2 on-board PGM outputs:

PGM1 and PGM2 - not used

PGM3 - form C relay output rated at 5A/

28Vdc, N.O./N.C (PGM4 optional)

MGRCV3SD_EI01.fm Page 1 Thursday, May 5, 2005 2:22 PM

2 Reference & Installation Manual

Specifications may change without prior notice.

1.2 System Features

• Auto-Panel Recognition

• Add up to 16 wireless transmitters and up to 16 remote controls

• On-board anti-tamper switch

• Full system supervision (check-in, low battery and tamper)

• Transmitter signal strength indicator

• Transmitter battery life display (Digiplex series only)

2.0 Installation

The following sections will detail how to mount and connect the MG-RCV3.

2.1 Location

The locations of the MG-RCV3 and wireless transmitters affect the overall

performance of the wireless system. In order to ensure the best possible signal

reception, the following list of location criteria should be respected whenever

possible:

• Select an installation site that is free of obstacles that reflect and absorb

radio frequency (RF) signals, as well as interference that may distort signals.

Avoid installation near or in the path of strong RF fields (i.e. neon lights,

computers), and on or near metal objects, circuit breaker boxes, air

• Approvals: 433MHz

868MHz

• Range (typical in a

residential environment): Refer to the appropriate transmitter

Instructions

Compliant to all EU and EFTA

countries except Greece according

to RTT&E directives.

868MHz version not approved by UL

MGRCV3SD_EI01.fm Page 2 Thursday, May 5, 2005 2:22 PM

Magellan Wireless Expansion Module 3

conditioners, and heater ducts since they may cause interference and reduce

the module’s sensitivity

• Select a site that is not susceptible to drastic temperature changes

• Mount the MG-RCV3 as central as possible to the proposed placement of the

transmitters

• Mount the MG-RCV3 as high as possible

• Avoid mounting the MG-RCV3 in the basement as the range of the module is

reduced when mounted below ground level. However, if it is absolutely

necessary to mount the module in the basement, mount the module as high

and as close to the underside of the first floor as possible

• Mount the MG-RCV3 on a wall allowing at least 5cm (2in) around the module

to permit adequate ventilation and heat dissipation

Refer to the appropriate Programming Guide for maximum allowable

distances between the control panel and the MG-RCV3.

2.2 Noise Level Test

The MG-RCV3 performs a test on power-up that verifies the noise level in the

surrounding environment. If the environment is too noisy, the module’s RX LED

will illuminate (refer to Figure 2.2 on page 6) and will remain illuminated until

the module is powered up again. In such cases, power down the Magellan

module, change its location, and then power up. Repeat this procedure until

the module’s RX LED no longer illuminates. If all possible mounting locations

have been tested and the environment is still too noisy, be aware that the

wireless system may not function properly. The noise level test should be

performed in conjunction with the signal strength test (refer to section 5.2 on

page 12) to ensure optimal mounting locations for the MG-RCV3 and

transmitters.

When performing the noise level test, ensure that there are no

transmitters that are powered-up.

2.3 Connections and Mounting

1. Using a screwdriver, remove the screw on the MG-RCV3’s front

cover and then remove the front cover.

MGRCV3SD_EI01.fm Page 3 Thursday, May 5, 2005 2:22 PM

4 Reference & Installation Manual

2. Firmly screw the antenna into the connector marked ANT on the

MG-RCV3 (refer to Figure 2.1 on page 5).

3. Remove the printed circuit board (PCB) by applying outward

pressure to the mounting clips (refer to Figure 2.1 on page 5) and

then lifting the PCB.

4. Using a drill or screwdriver, punch out the four mounting holes on

the back cover (refer to Figure 2.1 on page 5).

5. Align the six orientation holes (refer to Figure 2.1 on page 5) of the

PCB with the six pins on the back cover and snap the PCB into

place. If placed correctly, the antenna will lean directly over the

groove in the back cover.

6. Temporarily mount the MG-RCV3 in its proposed location (refer to

section 2.1 on page 2) with masking tape or any other temporary

adhesive.

7. Connect the MG-RCV3 to the control panel's communication bus

(Spectra) or combus (Digiplex series) in a star or daisy chain

configuration (refer to Figure 2.2 on page 6), and then power up.

8. Verify the environment noise surrounding the MG-RCV3 (refer to

section 2.2 on page 3).

9. Temporarily mount the transmitters in their proposed locations (refer

to section 2.1 on page 2) with masking tape or any other temporary

adhesive, insert the batteries and then close the transmitters’

covers.

10. Program the system (refer to section 3.0 on page 7).

Do not cut, bend, or alter the antenna. Ensure that the electrical wires

do not cross over the antenna when connected.

For Spectra systems, do not connect more than one MG-RCV3 to the

control panel. The MG-RCV3 does not function with control panels

that have a built-in wireless receiver, such as the Spectra 1759MG.

2.3.1 Programming a Wireless Fire Zone with a Spectra System

With Spectra systems, fire zones cannot be assigned to expansion

zones. As a result, when installing a wireless smoke detector to be

used with a Spectra system, the corresponding zone must be

programmed as follows:

MGRCV3SD_EI01.fm Page 4 Thursday, May 5, 2005 2:22 PM

Magellan Wireless Expansion Module 5

1. The zone must be defined as a 24Hr Burglary zone

2. The zone’s alarm type must be set to Audible Alarm (pulsed)

3. The zone’s Auto-Zone Shutdown (zone option [1]) and Bypass

(zone option [2]) features must be disabled.

4. Change the zone’s report code from a burglary report code to a fire

report code. If using Ademco Contact I.D., set the Contact ID

Options from All Codes to Programmable (section [136] option [3] =

OFF) and then enter the report code manually.

Refer to the appropriate Spectra Reference & Installation

Manual and Programming Guide for more information on zone

programming.

Figure 2.1: Mounting

MGRCV3SD_EI01.fm Page 5 Thursday, May 5, 2005 2:22 PM

6 Reference & Installation Manual

Figure 2.2: Connecting Magellan to the Control Panel

MGRCV3SD_EI01.fm Page 6 Thursday, May 5, 2005 2:22 PM

Autres manuels pour MG-RCV3

Table des matières

Autres manuels Paradox Unité de contrôle

Paradox

Paradox ZX16D Manuel utilisateur

Paradox

Paradox APR3-HUB2 Manuel utilisateur

Paradox

Paradox RTX3 Manuel utilisateur

Paradox

Paradox IP150 Mode d'emploi

Paradox

Paradox IP150+ Manuel utilisateur

Paradox

Paradox PCS265 LTE Guide d'installation

Paradox

Paradox IP150 Manuel utilisateur

Paradox

Paradox PCS265 LTE Guide d'installation

Paradox

Paradox DGP2-ZX4 Manuel utilisateur

Paradox

Paradox ZX8 Manuel utilisateur

Paradox

Paradox PCS265 Manuel utilisateur

Paradox

Paradox PGM82 Manuel utilisateur

Paradox

Paradox Spectra Digiplex NE APR3-HUB2 Manuel utilisateur

Paradox

Paradox PCS265LTE Guide d'installation

Paradox

Paradox Spectra 1759EX V1.0 Manuel utilisateur

Paradox

Paradox IP150 Manuel utilisateur

Paradox

Paradox RPT1+ Manuel utilisateur

Paradox

Paradox PCS250G Guide d'installation

Paradox

Paradox IP180 Manuel utilisateur

Paradox

Paradox ZX82 Manuel utilisateur

Paradox

Paradox VDMP3 Manuel utilisateur

Paradox

Paradox ZX32D Manuel utilisateur

Paradox

Paradox Digiplex Liberator DGP-319 Instructions de montage

Paradox

Paradox MG-RCV3 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur