PAR EverServ 600 Manuel utilisateur
PAR Everserv 600 User Manual
www.partech.com
Thank You!
Thank you for purchasing the EverServ
designed for your environment, your
success is our passion.
1Examine The Shipment
Please ensure all
equipment is
present.
Report any missing
or damaged equip-
ment to your PAR
Salesperson or PAR
Channel Partner.
2Inventory Components
3pre-installation overview
Ensure you have the items
listed below in your order.
Power Supply
VESA Adapter Plate
(M6150-10 Model Only)
EverServ 600
Power Cord
(Packaged Seperately)
Inventory the equipment in your order.
Before installing your new EverServ
600 system, ensure certain pre-
to protect the equipment, the store,
and the employees. If you have any
guidelines, contact a PAR sales
network cabling, you may need to
contact an electrical contractor to
perform this work.
770506502
This material has been created in order to accommodate a wide range of
-
While ParTech, Inc. (“PAR”) takes great care to ensure the accuracy of these
materials, all material is provided “as is” without warranty of any kind,
-
-
-
-
form or by any means, electronic or mechanical, including photocopying,
table of contents
I/O Board
Maintenance & Support
Page 5
Page 6
Page 7
Page 10
Page 11
EverServ 600 Series Models
Model 6150
4GB Memory
Intel® Celeron processor
64GB SSD
15” Projec�ve Capaci�ve
Pedestal (Counter)
Model 6150-10
4GB Memory
Intel® Celeron processor
64GB SSD
15” Projec�ve Capaci�ve
VESA Bracket (Wall Mount)
I/O Ports Cover
Cable Well Cover
Power Indicator
removing terminal from box
Remove the terminal from the box by grasping the sides of the air cushioned
DO NOT
Accessing the i/o well & Connecting Cables
connecting the power cable
Page 5
Remove the stand cover by
holding the terminal with
one hand and pulling the
bottom of the stand cover
by the cover hooks.
1
Connect your cables in the designat-
ed I/O ports and then route through
the terminal stand.
3
Remove the I/O cover by pressing the the two
tabs and pulling the cover straight up away
from the terminal.
2
Replace the I/O cover then the stand cover.
The stand cover should be replaced by rst
connecting the top tabs then pressing on the
bottom.
4
In order to power up the terminal you will
be required to connect the power the
cable.
Service & support
Page 6
123456810
7 9 11
1Cash Drawer
2USB 2.0
COM Ports 2x20 Display Power Connector LAN MSR, Biometric
Main i/o Board
Additional i/o
1 2
1SSD LAN
2COM1 (DB9)
3COM 2 (RJ45)
4COM 3 (RJ45)
52x20 Display
Only
6Power Input
7
8USB 2.0
9VGA
10 MSR
11 Audio
CAUTION BATTERY WARNING:
•
• The service related to human safety is not allowed because this device may have the possibility of the radio
interference.
•
• The EverServ 600 series terminals are EMC compliant for Class “A” digital device business purposes. The
harmful interference in a commercial environment. Equipment is not intended for home use.
Safety
Everserv 600 MSR & Biometrics Reader
Remove the I/O cover by
pressing the two tabs and
pulling the cover straight
up away from the terminal.
Replace the I/O cover.
1Attach the MSR/Biometric Unit to the terminal
using the included screws.
2
Connect the MSR cable to the MSR
port on the I/O Board. Once
connected route the cable through
the cable clips.
3
Inventory Components
MSR Unit
Philips Screws
Phillips head screwdriver
SOLD sepArately
NOTE: There are several op�ons for the MSR.
Your product may look different than the
image below.
Page 7
SOLD sepArately
Everserv 600 Customer Display
Customer Display
Philips Screws
Inventory Components
Phillips head screwdriver
Remove the I/O cover by
pressing the two tabs and
pulling the cover straight
up away from the terminal.
1Attach the Customer Display to the terminal
stand using the included screws.
2
Depending on Customer Display use the
VGA, USB or COM 4 (2x20 Display) ports to
connect display to terminal.
3
Replace the I/O cover.
Before installing your new EverServ 600
customer display you may need to enable the
VGA 12v power. If you are installing the K6622,
Customer Display 12v Power Setup
Begin by powering up the terminal. When you see the
pineapple touch the screen.
1
When the PAR BIOS Extensions screen appears, press
“Setup” button.
2
When the PAR BIOS Setup screen appears, press the“Next
Item”button until the VGA Port +12v is selected.
3When the VGA Port +12v is selected, press the“+”to
Enable the 12v power.
4
Once you have enabled the 12v power, press the “Save”
button then press the“Ok” button that appears below.
5
Once you have Saved, press the “Exit” button then press
the “Yes” button that appears below. The terminal will
reboot and the display will be ready to use. 2nd screen
functionality will automatically be congured.
6
Everserv 600 VESA Adapter plate
K6150
VESA Adapter Plate
Inventory Components
Phillips head screwdriver
Remove the four screws connecting the stand
to the touch screen.
KEEP THESE SCREWS FOR RE-USE.
2
Using the four screws from the stand (Step
2) connect the VESA Adapter Plate to the
touch screen.
3
Remove the stand cover by
holding the terminal with
one hand and pull the
bottom of the stand cover
by the cover hooks.
1
The terminal is now ready to be wall or pole
mounted to customer provided mount.
Page 10
Table des matières
Autres manuels PAR Terminal tactile
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
Amano
Amano MTX-15 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
