Panduit PANZONE PZAEWM6E Manuel utilisateur
INSTRUCTIONS CM698
© Panduit Corp. 2013
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Page 1 of 4
NOTE - Some views in this document may vary
slightly from your actual enclosure.
Venting for a 4" Fan
(2 plcs.)
Knockout for.50” and.75”
Conduit (4 plcs.)
Knockout for 1.75" and 2"
Conduit (8 plcs.)
Louvered Vents
Adjustable 3RU Equipment
Mounting Brackets
(4 plcs. - PZAEWM6E)
(2 plcs. - PZBASE3E)
(view shown with door removed)
PZAEWM6E
List of Components:
(1) PZASEWM6E Enclosure
(1) Panel Door
(1) Installation Instruction
(4) 3RU Equipment Mounting Brackets
(2) M5 Button Head Torx Screws
(10) M6 Hex Head Screws
(6) Pack of [4] #12-24 Screws
(1) Pack of [25] #12-24 Cage Nuts
P
AN
Z
ONE
Building Automation System Enclosure (Economy)
P
AN
Z
ONE
Active Wall Mount Enclosure (Economy)
Knockouts for
T70 Raceway
(4 plcs.)
THIS PRODUCT HAS A MAXIMUM LOAD RATING OF 100 LBS.
PZBASE3E
List of Components:
THIS PRODUCT HAS A MAXIMUM LOAD RATING OF 60 LBS.
(1) PZBASE3E Enclosure
(1) Panel Door
(1) Installation Instruction
(2) 3RU Equipment Mounting Brackets
(2) M5 Button Head Torx Screws
(4) M6 Hex Head Screws
(3) Pack of [4] #12-24 Screws
(1) Pack of [12] #12-24 Cage Nuts
INSTRUCTIONS CM698
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 4
1.3
Electrical Box
(2 plcs.)
1.2
Floor
2 X 4 Stud
Top
Mounting eyelets
16"
24"
Bottom
Mounting eyelets
Cable
Breakout
Electrical
Breakout
6’
36”
Step 1: Mounting Enclosure to Wall / Electrical Box Installation
1.1 Locate the wall studs (16" on center in most U.S.
cases). PANDUIT recommends mounting the top
of the enclosure at 6’ from the floor.
1.2 Determine if you will be mounting the electrical box
in the wall.
If Mounting Electrical Box in the Wall: Remove
desired breakout from back of enclosure. After
electrical box is completely installed, mount enclo-
sure to wall using 4 screws. Enclosure designed to
use #14 screws or M6 screws. (See figure 1.3)
INSTRUCTIONS CM698
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 4
Step 2: Door Removal and Installation
2.1 Use key to turn lock 1/4 turn
2.2 Pull top of door away from enclosure
3.3 Lift door up and away from enclosure
3.4 Reverse steps to install door
1/4 Turn Lock
Step 3: Optional Fan Installation (if required, sold separately)
3.1 Break out vent space on bottom of enclosure.
3.2 Place fan over opening. Line up the bottom fan
cover to the outside of enclosure and screw
into place.
3.3 Line up top fan cover and screw into place.
3.4 Determine the length of the power cord that is
desired. Strip back the insulation on the cord
and terminate to the plug.
3.5 Attach the power cord. The fan can be plugged
into an the electrical box inside the enclosure.
Break out
vent space
Step 4: Optional Back Plate Installation (PZBASE3E ONLY, sold separately)
4.1 Position Back Plate (p/n PZBASE3EBP -or-
PZBASE3EPBP) inside PZBASE3E enclosure.
4.2 Secure Back Plate to enclosure with [4] M5
Serrated Hex Nuts (use 8mm socket wrench).
[4] M5 Serrated Hex Nuts
(use 8mm socket wrench)
PZBASE3EBP
-or-
PZBASE3EPBP
PZBASE3E ONLY
INSTRUCTIONS CM698
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
E-mail:
Phone:
866-405-6654
www.panduit.com
Page 4 of 4
Step 5: 3RU Equipment Mounting Bracket Installation
5.1 Locate and install 3RU Equipment Mounting Brackets. Either Cage Nut cutouts or #12-24 tapped mounting holes
can be used; brackets are reversible. Brackets mount in vertical, horizontal, or 45º diagonal positions.
5.2 Depending on bracket orientation, use number of M6 hex head screws listed below (use 10mm socket wrench).
5.3 Install brackets in pairs in mirrored locations on left and right sides of enclosure.
3RU Equipment
Mounting Bracket
VERTICAL ORIENTATION
[2] - M6 Hex Head Screws
3RU Equipment
Mounting Bracket
HORIZONTAL ORIENTATION
[3] - M6 Hex Head Screws
3RU Equipment
Mounting Bracket
45ºDIAGONAL ORIENTATION
[2] - M6 Hex Head Screws
3RU Equipment
Mounting Brackets
INSTALL IN PAIRS
M6 Hex Head Screws
(use 10mm socket wrench)
Ce manuel convient aux modèles suivants
1
Autres manuels Panduit Enceinte
Panduit
Panduit PANZONE PZC12S Manuel utilisateur
Panduit
Panduit PANZONE PZBASE3 Manuel utilisateur
Panduit
Panduit PZWIFIE Manuel utilisateur
Panduit
Panduit NET-ACCESS CN3 Manuel utilisateur
Panduit
Panduit FRME1 Manuel utilisateur
Panduit
Panduit FCE4U Manuel utilisateur
Panduit
Panduit Z23U-624 Guide de l'utilisateur
Panduit
Panduit FMT1J Manuel utilisateur
Panduit
Panduit E6212B1FP Manuel utilisateur
Panduit
Panduit PANZONE PZC12S Manuel utilisateur
Panduit
Panduit PZWRKA Manuel utilisateur
Panduit
Panduit Panzone PZWMC12P Manuel utilisateur
Panduit
Panduit PANZONE PZRFE4U Manuel utilisateur
Panduit
Panduit IAEIP66 Manuel utilisateur
Panduit
Panduit FWME4 Manuel utilisateur
Panduit
Panduit UICFPR4 Series Manuel utilisateur
Panduit
Panduit NET-ACCESS N21SPH Manuel utilisateur
Panduit
Panduit FCE1U Manuel utilisateur
Panduit
Panduit PanZone Series Manuel utilisateur
Panduit
Panduit PANZONE PZWMC Manuel utilisateur
