Panduit FCE1U Manuel utilisateur

INSTALLATION INSTRUCTIONS FS006

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 1 of 11

OPTICOM QUICKNET Rack Mount Fiber Cassette Enclosures

Part Numbers: FCE1U, FCE1UA, FCE2U

1 ENCLOSURE

2 (3) TAK-TYTa p e ( 6 "pcs.)

2 (3) ADHESIVE MOUNTS

2 SLACK SPOOLS

1 (2) #10-32 x 3/8"SCREW

3 (4) #10-32 HEX NUTS

WARNING: UNMATED CONNECTORS MAY EMIT INVISIBLE LASER RADIATION. DO NOT LOOK DIRECTLY INTO THE END OF THE

CONNECTOR. DO NOT INSPECT WITH MAGNIFYING DEVICES. MAINTAIN DUST CAPS ON UNMATED CONNECTORS.

CAUTION:

Fiber optic cable is sensitive to excessive pulling, bending, and crushing forces. Consult the manufacturer’s cable specification sheet for the

specific cable in use.

Follow TIA/EIA-568-A, 569, 606, and 607 installation guidelines where applicable.

Care should be taken when opening or closing a fully loaded drawer in order to protect the fiber components.

Contents

1 (2) FIBER GROMMETS

4 #M6 x 1 SCREWS

1 (2) STRAIN RELIEF BRACKET

4 CABLE TIES (PLT2S-M0)

2 (4) PLUNGERS AND GROMMETS

2 (4) BEND RADIUS CLIPS

4 #12-24 x 1/2"SCREWS

1 CAUTION LABEL

1 LASER WARNING LABEL

3 BEVELED ENTRY CLIPS

Enclosure

Trunk or Interconnect

Cable Entry Grommet

ASSEMBLY VIEW OPTICOM Fiber Adapter Panel (FAP) Installation (FAPs not included).

FCE1U

Strain Relief

Bracket

Cover (field removable)

Bend Radius

Control Clip

Door Assembly

(shown in open

position)

FCE1UA (FCE2U)

Figure 1

Plunger and

Grommet

Enclosure Sliding Drawer

Fiber Adapter Panels (FAPs):

Up to 4 for FCE1U, FCE1UA.

Up to 8 for FCE2U.

INSTALLATION INSTRUCTIONS FS006

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 2 of 11

Enclosure Mounting Brackets

Figure 4

Determine where the cable will enter the enclosure.

Carefully remove the knock-out at that entry location

of the fiber tray so as not to damage surrounding

sheet metal. DO NOT Install grommet at this stage,

grommet will be installed after enclosure is mounted

to rack.

Note: Cover removal is not required for proper

fiber optic cabling installation.

To remove the cover if desired, unscrew the four

#4-40 screws and lift cover up and off.

#4-40 screws

Use (2) #12-24 X 1/2"

screws (provided). Repeat

for other side.

Place enclosure mounting brackets at desired

position on the rack. Mount the enclosure to the

rack using (4) #12-24 x 12"screws. Use (4)

M6 x 1 screws if mounting to a metric rack.

Figure 2

Figure 3

Figure 4A

Preparation and Rack Mounting

INSTALLATION INSTRUCTIONS FS006

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 3 of 11

After the enclosure is mounted to the rack, determine

the size of the innerduct that will be used to bring the

cable into the enclosure. Install grommet following the

proper cutting diagram.

Cut the small circle

for 1"diameter

innerduct.

Cut the large circle

for 1-1/2"diameter

innerduct.

Cut the straight

lines when not

using any

innerduct.

Place the strain relief bracket adjacent to the knocked

out enclosure entry point. Fasten with #10-32 x 3/8"

screw and hex nut.

Strain Relief

Bracket

#10-32 x 3/8"

Screw

#10-32 Hex

Nut

Figure 5

Figure 5A

Figure 6

Note: Cover not shown for clarity.

INSTALLATION INSTRUCTIONS FS006

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 4 of 11

Insert QUICKNET Pre-Terminated Fiber Optic

Cassettes into the enclosure as shown. Once

mounted, fully seat NyLatch fasteners to

secure the cassette.

Figure 7

Figure 7A

Cassettes: Up to 4 for FEC1U, FCE1UA.

Up to 8 for FCE2U.

Fully extend drawer to ensure proper amount of

slack is used.

Isometric view showing drawer

fully extended and tilted down

(cables omitted for clarity).

QUICKNET Cassette Installation (cassettes not included)

INSTALLATION INSTRUCTIONS FS006

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 5 of 11

Route fiber through grommet to fiber

cassettes as shown. Leave enough

slack so that when the drawer is fully

extended, cables are not put under

tension. However, do not use so

much slack that drawer cannot be

returned to the home position. (See

Fig 7C)

Use TAK-TYTape to secure fiber

cords at cable entry location and

other points as shown.

Drawer in extended position Figure 7B

Figure 7C

Free Floating

TAK-TYTape

Adhesive

Bevel Entry

Clips. Note

location and

position of

clips.

Drawer in home position

Grommet

Fixed

TAK-TY

Tape

USE TAK-TYTape to fasten

cable to fence outer slots.

Cable length

between point “A”

and point “B” is

approx. 34"

[.864m].

“A”

“B”

INSTALLATION INSTRUCTIONS FS006

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 6 of 11

Place slack spools over #10-32 studs on sliding

tray. Secure with #10-32 hex nuts and/or adhesive

mounts (be sure to punch hole into adhesive

mounts). Note spool orientation.

Position FAPs between upright flanges as shown.

Once mounted, fully seat NyLatch fasteners to

secure FAPs.

Slack Spools

Field Termination or Pre-Terminated Trunk Installation

Figure 8

Figure 8A

Isometric view showing drawer

fully extended and tilted down

(cables omitted for clarity).

Fully extend drawer to ensure proper amount of

slack is used.

Top view with cover removed.

Please note orientation of spools.

Fiber Adapter Panels (FAPs):

Up to 4 for FEC1U, FCE1UA.

Up to 8 for FCE2U.

INSTALLATION INSTRUCTIONS FS006

For Technical Support: www.panduit.com/resources/install_maintain.asp

UseTAK-TYTape to fasten

cable to fence.

Page 7 of 11

Drawer in home position

Figure 8B

Figure 8C

Drawer in extended position.

Free floating

TAK-TY.

Grommet

Fixed TAK-TY

Tape

Individual

fiber breakout

point.

(See Detail at

right).

Route fiber through grommet as shown.

Use enough cable length to ensure one

complete loop (approx. 52" [1.32m]) of

individual fibers around slack spools.

Leave enough jacketed slack so when

the drawer is fully extended the cables

are not put under tension. However, do

not use so much slack that drawer

cannot be returned to its home position.

(See Figure 8C)

Use TAK-TYTape to secure fiber cords at

cable entry location and other points as

shown.

Adhesive

Mount

w/TAK-TYTape

cable jacket

individual fiber

Fiber Breakout Detail

Be sure adhesive mount secures jacketed

Trunk cable. DO NOT clip individual

900µm buffered fibers.

Sub-unit

tubes.

1.0"

“A”

“B”

Cable length

between point “A”

and point “B” is

approx. 36"

[.914m].

[25.4m]

INSTALLATION INSTRUCTIONS FS006

For Technical Support: www.panduit.com/resources/install_maintain.asp

Fiber Adapter Panels (FAPs):

Up to 4 for FEC1U, FCE1UA. Up to 8 for FCE2U.

FOSM Fiber Optic Splice Module Installation

Place “L”shape support brackets over

#10-32 studs on sliding tray, note orientation.

Place first FOSMH1U (FOSMH2U) on top of

“L”shape support brackets, note orientation

and secure with #10-32 hex nuts. Remaining

FOSMs are stacked on top of each other and

snap in place.

If 4 FOSMs are to be installed in the FCE1U

or FCE1UA, side latches on top module must

be broken off to close enclosure drawer.

Position FAPs between upright flanges as

shown. Once mounted, fully seat NyLatch

fasteners to secure FAPs.

Page 8 of 11

Figure 9

Break off FOSM latch

on top module only.

Isometric view showing drawer

fully extended and tilted down

(cables omitted for clarity).

Figure 9A

Fully extend drawer to ensure proper amount of slack

is used.

Finish splicing in each FOSM before adding/stacking

subsequent FOSMs.

FOSM: Up to 4 for FEC1U, FCE1UA.

Up to 8 for FCE2U.

FOSMH1U

(FOSMH2U)

Support

Brackets

INSTALLATION INSTRUCTIONS FS006

For Technical Support: www.panduit.com/resources/install_maintain.asp

Drawer in home position

Page 9 of 11

Figure 9C

Drawer in extended position Figure 9B

Fixed TAK-TY

Tape

Grommet

Route fiber through grommet as shown.

Use enough cable length to ensure one

complete loop (approx. 45" [1.15m]) of

individual fibers around FOSM slack

spools.

Route 900µm buffered fiber from the

trunk cable and splice to pigtail per

instructions in FS001, “OPTICOM Fiber

Optic Splice Module Installation

Instructions.”

Leave enough jacketed slack so when

the drawer is fully extended the cables

are not put under tension. However, do

not use so much slack that the drawer

cannot be returned to its home position.

(See Figure 9C)

Use TAK-TYTape to secure fiber cords at

cable entry location and other points as

shown.

Individual

fiber

breakout

point (See

Fiber

Breakout

Detail on

page 7).

Free-floating

TAK-TYTape

Use TAK-TYTape to

fasten cable to fence.

Sub-unit

tubes

“A”

“B”

Cable length

between point

“A” and point

“B” is approx.

36" [.914m].

INSTALLATION INSTRUCTIONS FS006

For Technical Support: www.panduit.com/resources/install_maintain.asp

Plunger

and

Grommet

Bend Radius

Control Clip

Grommet

Plunger.

Install plunger into grommet, but do not fully

seat. Slide bend radius clips over sliding tray

flange as shown. Push grommet/plunger

through bend radius clip and sliding tray flange

holes. Finally fully seat plunger into grommet

securing bend radius clip.

Bend Radius

Control Clips

Plunger and

Grommet

Page 10 of 11

Figure 10

Figure 10A

Sliding Tray

Flange

Figure 11

Patch Cord Bend Radius Clip Installation

Install patch cords into FAPs/cassettes routing

through bend radius control clips and

maintaining proper patch cord bend radius.

Autres manuels pour FCE1U

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panduit Enceinte

Panduit

Panduit PANZONE PZWC35 Manuel utilisateur

Panduit

Panduit PANZONE PZAEWM6E Manuel utilisateur

Panduit

Panduit FRME2 Manuel utilisateur

Panduit

Panduit NET-ACCESS CN3 Manuel utilisateur

Panduit

Panduit PANZONE PZWIFIENA Manuel utilisateur

Panduit

Panduit IAEIP66 Manuel utilisateur

Panduit

Panduit Panzone PZWMC12P Manuel utilisateur

Panduit

Panduit FMT1J Manuel utilisateur

Panduit

Panduit FCE4U Manuel utilisateur

Panduit

Panduit PANZONE PZWMC Manuel utilisateur

Panduit

Panduit E6212B1FP Manuel utilisateur

Panduit

Panduit Z23U-624 Guide de l'utilisateur

Panduit

Panduit PanZone PN323 Manuel utilisateur

Panduit

Panduit PANZONE PZC12S Manuel utilisateur

Panduit

Panduit FLEX-ZRFEG Manuel utilisateur

Panduit

Panduit ZDF48-RA Manuel utilisateur

Panduit

Panduit NET-ACCESS N21SPH Manuel utilisateur

Panduit

Panduit PANZONE PZBASE3 Manuel utilisateur

Panduit

Panduit PZWRKA Manuel utilisateur

Panduit

Panduit PANZONE PZC12S Manuel utilisateur

Panduit

Panduit PANZONE PZWIFIEW Manuel utilisateur

Panduit

Panduit N2RCFR Manuel utilisateur

Panduit

Panduit FCE1U Manuel utilisateur

Panduit

Panduit PZWIFIEN Manuel utilisateur

Manuels Enceinte populaires d'autres marques

SilentiumPC

SilentiumPC Armis AR5 Manuel

Pulsar

Pulsar 17/TRP80/DSPR Manuel utilisateur

Thermaltake

Thermaltake V150 TG Manuel utilisateur

MSI

MSI MPG SEKIRA 500X Manuel utilisateur

Antec

Antec Dark fleet DF-10 Manuel utilisateur

Nexans

Nexans WTC05 Manuel utilisateur

Peavey

Peavey DS 1502 Manuel utilisateur

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuel utilisateur

Rosewill

Rosewill RX82-U(JBOD) Manuel utilisateur

QNAP

QNAP SAS JBOD CLI 1.0 Manuel utilisateur

GAMDIAS

GAMDIAS Talos P1 Manuel utilisateur

Auvs

Auvs KR615 Manuel utilisateur

Digitus

Digitus DA-71114 Manuel utilisateur

CommScope

CommScope FDH 3000 Manuel utilisateur

FS FHD-FWME4 Manuel utilisateur

JBL

JBL CS1215T Manuel utilisateur

Pulsar

Pulsar ARAD-S4 Manuel utilisateur

Pulsar

Pulsar AWO454 Manuel utilisateur