Panasonic PT-AE2000E Manuel du système

< 1 >

SPEC FILE

Product Number : PT-AE2000

Product Name : Full High-Definition Home Cinema Projector

As of September 2007. Appearance and specifications are subject to change without notice.

SPEC FILE

PT-AE2000

Full High-Definition Home Cinema Projector

As of September 2007 < 2 >

Specifications

Main Unit

Power supply:

Power consumption:

LCD*1panel: Panel size:

Display method:

Drive method:

Pixels:

Lamp*2:

Lens:

Screen size:

Throw distance:

Colours:

Brightness*3:

Centre-to-corner uniformity ratio*3:

Contrast*3:

Resolution:

Scanning frequency: RGB:

YPBPR(YCBCR):

S-Video/Video:

Optical axis shift*5:

Keystone correction range:

Installation:

OSD languages:

Terminals: HDMI*6IN:

COMPUTER IN:

R, G, B:

HD/SYNC, VD:

COMPONENT IN:

PB/CB, PR/CR:

VIDEO IN:

S-VIDEO IN:

SERIAL IN:

100– 240 V AC, 50/60 Hz

240 W (0.08 W in standby mode with fan stopped)

0.74˝ diagonal (16:9 aspect ratio)

Transparent LCD panel (x 3, R/G/B)

Active matrix

2,073,600 (1,920 x 1,080) x 3, total of 6,220,800 pixels

165 W UHM™ lamp

Powered zoom/focus lens (1:1–1:2), F 1.9–3.2, f 22.4– 44.8 mm

40– 200 inches

1.2–12.0 m (3´11˝– 39´4˝) (16:9 aspect ratio)

Full colour (1,073,741,824 colours)

1,500 lumens*4

85 %

16,000:1*4(full on/full off)

1,920 x 1,080 pixels

fH30–70 kHz, fV50– 87 Hz,

Dot clock: Less than 150 MHz

480i (525i): fH15.75 kHz; fV60 Hz,

576i (625i): fH15.63 kHz; fV50 Hz,

480p (525p): fH31.5 kHz; fV60 Hz,

576p (625p): fH31.25 kHz; fV50 Hz,

720/50p (750/50p): fH37.5 kHz; fV50 Hz,

720/60p (750/60p): fH45 kHz; fV60 Hz,

1080/50i (1125/50i): fH28.125 kHz; fV50 Hz,

1080/60i (1125/60i): fH33.75 kHz; fV60 Hz,

1080/24p (1125/24p): fH27 kHz; fV24 Hz,

1080/50p (1125/50p): fH56.3 kHz; fV50 Hz,

1080/60p (1125/60p): fH67.5 kHz; fV60 Hz

fH15.75 kHz fV60 Hz (NTSC, NTSC4.43, PAL-M, PAL60)

fH15.63 kHz fV50 Hz (PAL, PAL-N, SECAM)

Horizontal: ±40%, vertical: ±100%

Vertical: approx. ±30°

Ceiling/floor, front/rear (menu selection)

English, French, German, Spanish, Italian, Chinese, Korean, Russian,

Swedish, Danish, Norwegian, Polish, Czech, Hungarian, Portuguese,

Thai

HDMI connector x 3

D-sub HD 15-pin (female) x 1

0.7 Vp-p (1.0 Vp-p for Sync on G), 75 ohms

TTL, high impedance (positive/negative polarity)

RCA pin (Y, PB/CB, PR/CR) x 2

1.0 p-p, 75 ohms

0.7 Vp-p, 75 ohms

RCA pin x 1, 1.0 Vp-p, 75 ohms

Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms

D-sub 9-pin (RS-232C) x 1, for external control

SPEC FILE

PT-AE2000

Full High-Definition Home Cinema Projector

As of September 2007 < 3 >

Power cord length:

Cabinet material:

Dimensions (W x H x D):

Weight:

Operating temperature:

Operating humidity:

Remote Control Unit

Power supply:

Operation range*8:

Dimensions (W x H x D):

Weight:

Supplied Accessories

Optional Accessories

3 m (9´10˝)

PC + ABS

460 x 130 x 300 mm (18-1/8˝ x 5-1/8˝ x 11-25/32˝)*7

7.2 kg (15.9 lbs.)

0°–40°C (32°–104°F)

20%–80% (no condensation)

3 V DC (AA type battery x 2)

Approx. 7 m when operated from directly in front of the signal receptor

52 x 200 x 28.5 mm (2˝ x 6-15/16˝ x 7/8˝)

170 g (6 oz.)

Power cord

Wireless remote control unit

Batteries for remote control (AA type x 2)

Replacement lamp: ET-LAE1000

Ceiling mount bracket for high ceilings: ET-PKE2000

Ceiling mount bracket for low ceilings: ET-PKE1000S

Cable cover: ET-PCE2000

Weights and dimensions shown are approximate.

Specifications subject to change without notice.

*1: The projector uses a type of liquid crystal panel that typically consists of millions of pixels. This panel is built with very high-precision tech-

nology to provide the finest possible image. Occasionally, a few pixels may remain turned on (bright) or turned off (dark). Please note that this

is an intrinsic characteristic of the manufacturing technology that affects all products using LCD technology.

*2: The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to

illuminate, due to impact or extended use. The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending

on individual lamp characteristics and usage conditions.

*3: Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.

*4: In AI mode, with dynamic iris on.

*5: Shift range is limited during simultaneous horizontal and vertical shifting.

*6: Supports Deep Color and xvYCC color space (effective in Color 1 image mode) of HDMI 1.3a standard.

*7: Lens and legs not included.

*8: Operation range differs depending on environments.

SPEC FILE

PT-AE2000

Full High-Definition Home Cinema Projector

As of September 2007 < 4 >

Dimensions

315

116

147

130

70 300

460

(12-13/32˝)

(4-9/16˝)

(5-25/32˝)

(5-1/8˝)

(2-3/4˝) (11-25/32˝)

(18-1/8˝)

unit : mm (inch)

NOTE: This illustration is not drawn to scale.

Terminals

COMPUTER IN connector pin assignment

1 HDMI 1 input

2 HDMI 2 input

3 HDMI 3 input

4 Computer input

5 Component (YPBPR/YCBCR) 1 input

6 Component (YPBPR/YCBCR) 2 input

7 S-Video input

8 Serial input

9 Video input

no.

signal

GND

signal

GND

signal

GND

HD/SYNC

123 4 5 6 7 8

11615

510

D-sub HD 15-pin, female

SPEC FILE

PT-AE2000

Full High Definition Home Cinema Projector

As of September 2007 < 5 >

Projection distance (screen aspect ratio 16:9)

Diagonal length

Projection size (16:9) Height from the

edge of screen to

centre of lens

(E)

Width from the

right edge of screen to

centre of lens

(W)

Projection distance (L)

Min (Wide) Max (Telephoto)

1.01 m

1.52 m

2.03 m

2.54 m

3.05 m

3.81 m

5.08 m

1.2 m

1.8 m

2.4 m

3.0 m

3.6 m

4.5 m

6.0 m

2.3 m

3.5 m

4.7 m

6.0 m

7.2 m

9.0 m

12.0 m

0.75 m

1.13 m

1.50 m

1.87 m

2.25 m

2.81 m

3.74 m

0.80 m

1.20 m

1.60 m

2.00 m

2.40 m

2.99 m

3.99 m

-0.25 m

-0.38 m

-0.50 m

-0.63 m

-0.75 m

-0.94 m

-1.25 m

0.09 m

0.14 m

0.18 m

0.23 m

0.27 m

0.34 m

0.45 m

–

40˝

60˝

80˝

100˝

120˝

150˝

200˝

3´11˝

5´10˝

7´10˝

10´2˝

11´10˝

14´9˝

19´8˝

7´7˝

11´6˝

15´5˝

19´8˝

23´7˝

29´6˝

39´4˝

9.8˝

1´3˝

1´8˝

2´1˝

2´6˝

3´1˝

4´1˝

3.5˝

5.5˝

7˝

9˝

11˝

1´1˝

1´6˝

2´6˝

3´8˝

4´11˝

6´2˝

7´5˝

9´3˝

12´3˝

2´7˝

3´11˝

5´3˝

6´7˝

7´10˝

9´10˝

13´1˝

Projection distance (screen aspect ratio 4:3)

Diagonal length

Projection size (4:3) Height from the

edge of screen to

centre of lens

(E)

Width from the

right edge of screen to

centre of lens

(W)

Projection distance (L)

Min (Wide) Max (Telephoto)

1.01 m

1.52 m

2.03 m

2.54 m

3.81 m

1.5 m

2.2 m

3.0 m

3.7 m

5.6 m

2.9 m

4.3 m

5.8 m

7.3 m

11.0 m

0.91 m

1.37 m

1.82 m

2.28 m

3.42 m

0.73 m

1.09 m

1.46 m

1.82 m

2.74 m

-0.30 m

-0.45 m

-0.60 m

-0.76 m

-1.14 m

0.08 m

0.12 m

0.16 m

0.20 m

0.30 m

–

40˝

60˝

80˝

100˝

150˝

4´11˝

7´3˝

9´10˝

12´2˝

18´4˝

9´6˝

14´1˝

19´

23´11˝

36´1˝

11.8˝

1´6˝

2´

2´6˝

3´9˝

3.1˝

4.7˝

6.3˝

7.9˝

11.8˝

3´

4´6˝

6´

7´6˝

11´3˝

2´5˝

3´7˝

4´9˝

6´

9´

Calculation of the projection distance

For a screen size different from the above, use the equation below to calculate the projection distance.

16 : 9 minimum L (m) = (diagonal screen size in inches) x 0.0302 - 0.04

maximum L (m) = (diagonal screen size in inches) x 0.0604 - 0.05

4 : 3 minimum L (m) = (diagonal screen size in inches) x 0.0371 - 0.04

maximum L (m) = (diagonal screen size in inches) x 0.0739 - 0.05

NOTE: The values of L shown above vary due to characteristics of the zoom lens. Images may slightly distort due to characteristics of the zoom

lens when the zoom lens is set to the minimum throw distance.

NOTE: The accuracy of calculated value by the formula shown above is ±5%.

Standard setting-up positions

Upper edge of projected image

Lower edge of projected image

Projected image

HHW

Projected image

181

(7-1/8˝)

70 (2-3/4˝)

150

(5-29/32˝)

(2-9/16˝)

unit : mm (inch)

NOTE:

Illustrations show the projector installed

using optional ceiling bracket ET-PKE1000S.

This illustration is not drawn to scale.

Values shown are approximate.

SPEC FILE

PT-AE2000

Full High-Definition Home Cinema Projector

As of September 2007 < 6 >

Shift range

Optical axis shift function allows to shift the position of a projected image as shown below.

1.0V 1.0V

0.4H 0.4H

(Width of

projected image)

(Height of

projected image)

Standard position

of projected image

Installable angle

Install the projector at an angle within the range shown below.

• Vertical direction

The projector may be installed at a vertical angle of ±30°.

• Horizontal direction

The projector may not be angled horizontally.

+30°

-30°

0°

SPEC FILE

PT-AE2000

Full High-Definition Home Cinema Projector

As of September 2007 < 7 >

List of Compatible Signals

NTSC/NTSC4.43/PAL-M/PAL60

PAL/PAL-N/SECAM

480i (525i)

576i (625i)

480p (525p)

576p (625p)

720 (750)/60p

720 (750)/50p

1080 (1125)/60i

1080 (1125)/50i

1080 (1125)/24p

1080 (1125)/60p

1080 (1125)/50p

VGA480

WIDE480

SVGA

WIDE600

WIDE720

XGA

WIDE768

MXGA

SXGA

WIDE768-2

SXGA60+

WIDE800

WIDE900

720 x 480i

720 x 576i

720 x 480i

720 x 576i

720 x 480

720 x 576

1,280 x 720

1,920 x 1,080i

1,920 x 1,080

640 x 480

856 x 480

800 x 600

1,072 x 600

1,280 x 720

1,024 x 768

1,280 x 768

1,125 x 864

1,280 x 1,024

1,360 x 768

1,400 x 1,050

1,280 x 800

1,440 x 900

15.7

15.6

15.7

15.6

31.5

31.3

45.0

37.5

33.8

28.1

27.0

67.5

56.3

31.5

37.5

43.3

72.1

30.1

35.2

37.9

48.1

46.9

53.7

37.2

45.1

48.4

56.5

60.0

68.7

72.1

45.3

64.0

67.5

64.0

48.8

65.1

49.7

55.9

59.9

50.0

59.9

50.0

59.9

50.0

60.0

50.0

60.0

50.0

24.0

60.0

50.0

59.9

75.0

85.0

138.0

60.1

56.3

60.3

72.2

75.0

85.1

59.9

60.1

60.0

70.1

75.0

85.0

89.0

56.5

71.2

74.9

60.0

59.8

59.9

59.8

59.9

13.5

27.0

74.3

148.5

25.2

31.5

36.0

62.3

31.5

36.0

40.0

50.0

56.3

51.4

76.5

65.0

75.0

78.8

94.5

99.2

76.2

94.2

108.0

74.3

122.4

83.5

106.5

VIDEO/S-VIDEO

COMPONENT

COMPONENT/HDMI

COMPONENT/PC/HDMI

COMPONENT/HDMI

COMPONENT/PC/HDMI

PC/HDMI

Display mode Display

resolution

(dots)

(kHz)

Scanning frequency

(kHz)

Dot clock

frequency

(MHz)

Picture

quality

Format

Computer data compatibility

This projector accepts up to 70 kHz horizontal scanning frequency and 150 MHz dot clock.

NOTE: The display resolution of this projector is 1920 x 1080 pixels. If the display resolution indicated in the above data does not match

this resolution, the input signal will be converted to 1920 x 1080 pixels.

1. The “i” appearing after the resolution indicates an interlaced signal.

2. The following symbols are used to indicate picture quality.

AA Maximum picture quality can be obtained.

A Signals are converted by the image processing circuit before picture is projected.

SPEC FILE

PT-AE2000

Full High-Definition Home Cinema Projector

As of September 2007 < 8 >

Serial connector

The serial connector complies with RS-232C. To control the projector from a personal computer, com-

mands must be input through communication software, based on the format and satisfying the commu-

nication conditions shown below.

Pin assignments and signal names

Communication conditions (factory setting)

Basic format

Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent

in this order. Add parameters according to the details of control.

No.

Signal name

–

TXD

RXD

–

GND

Signal name

–

RTS

CTS

–

Description

Send data

Receive data

Ground

Description

Connected internally

Signal level

Synchronization method

Baud rate

Parity

Character length

Stop bit

X parameter

Sparameter

RS-232C-compliant

Start-stop synchronization

9,600 bps

None

8 bits

1 bit

None

D-sub 9-pin

STX ETXC1 C2 C3 : P1 P2 P3 P4

Start

(1 byte)

End

(1 byte)

Colon

(1 byte)

Parameter

(1-4 bytes)Command

(3 bytes)

(Control and/or query commands)

CAUTIION

When sending multiple commands, be sure to send the next command after receiving a response from the projector.

Cable specifications

PC (DTE)Projector

DSR

SPEC FILE

PT-AE2000

Full High-Definition Home Cinema Projector

As of September 2007 < 9 >

Status asking commands

Command Description Callback

QPW

QIN

QPM

QFZ

QOT

QSH

QWM

Standby power status

Input signal status

Picture mode status

Freeze status

Off timer status

Shutter function status

Waveform monitor status

Normal

Dynamic

Cinema 1

Cinema 2

Cinema 3

Colour 1

Colour 2

<NOR>

<DYN>

<CN1>

<CN2>

<CN3>

<CL1>

<CL2>

<off_on>

<off_timer>

<off_on>

<x>

Control commands

*Do not send PON, POF, or OSH commandscontinuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.

PON*

POF*

IIS:<input signal>

OFZ:<off_on>

OEN

VPM:<picture mode>

<NOR>

<DYN>

<CN1>

<CN2>

<CN3>

<CL1>

<CL2>

OMN

OCU

OCD

OCL

OCR

OSH*

OST

OVM

VS1

OBK

OLE

OOT:<off_timer>

OWM:<x>

Power on (standby mode on)

Power off (standby mode off)

Input signal selection

Freeze

Enter

Picture mode

Normal

Dynamic

Cinema 1

Cinema 2

Cinema 3

Colour 1

Colour 2

Cursor up

Cursor down

Cursor left

Cursor right

Shutter

The same function as“DEFAULT” button

The same function as“PICTURE MODE” button

The same function as“ASPECT” button

The same function as“RETURN” button

The same function as“LENS” button

Off timer

Waveform monitor activate/off

PON

POF

IIS:<input signal>

OFZ:<off_on>

OEN

VPM:<picture mode>

<NOR>

<DYN>

<CN1>

<CN2>

<CN3>

<CL1>

<CL2>

OMN

OCU

OCD

OCL

OCR

OSH

OST

OVM

VS1

OBK

OLE

OOT:<off_timer>

OWM:<x>

–

Command: <Parameter> Function Callback: <Parameter> Parameter value

Min Max

SPEC FILE

PT-AE2000

Full High-Definition Home Cinema Projector

As of September 2007 < 10 >

Parameter format

Parameter format Size (Byte) Difinition

<off_on>

<off_timer>

<x>

0 = off, 1 = on

VID = video, SVD = S-video, RG1 = computer, CP1 = component 1,

CP2 = component 2, HD1 = HDMI 1, HD2 = HDMI 2, HD3 = HDMI 3

000 = power on (standby mode on), 001 = power off (standby mode off)

0 = off, 1 = 60 min, 2 = 90 min, 3 = 120 min, 4 = 150 min, 5 = 180 min,

6 = 210 min, 7 = 240 min

0 = off, 1 = full scan (Y), 2 = full scan (R), 3 = full scan (G), 4 = full scan (B),

5 = single line (Y), 6 = single line (R), 7 = single line (G), 8 = single line (B)

Command example

To set the volume to +30, send the command as shown below.

STX AVL : 30 ETX

Start Command Parameter End

NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.

NOTE: When sending commands without parameters, a colon (:) is not necessary.

Autres manuels pour PT-AE2000E

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Projecteur

Panasonic

Panasonic PT-VW430U Manuel utilisateur

Panasonic

Panasonic PT-L502 Manuel utilisateur

Panasonic

Panasonic PTAE500U - LCD PROJECTOR Manuel utilisateur

Panasonic

Panasonic PT-DW6300ES Manuel utilisateur

Panasonic

Panasonic PT-FRQ60 Manuel utilisateur

Panasonic

Panasonic PT-A900E Manuel utilisateur

Panasonic

Panasonic PT-DZ21KU Manuel utilisateur

Panasonic

Panasonic PT-VW330U Manuel utilisateur

Panasonic

Panasonic PT-RZ660 Manuel utilisateur

Panasonic

Panasonic Presentation Solutions Manuel utilisateur

Panasonic

Panasonic PT-TW340 Manuel utilisateur

Panasonic

Panasonic PT-VX400NTU Manuel utilisateur

Panasonic

Panasonic PT-AR100U Manuel utilisateur

Panasonic

Panasonic PT-LMZ460 Mode d'emploi

Panasonic

Panasonic PT-DW740E Manuel utilisateur

Panasonic

Panasonic PTL501U - LCD PROJECTOR Manuel utilisateur

Panasonic

Panasonic PT-VX400 Manuel utilisateur

Panasonic

Panasonic PT-51D31CE Manuel utilisateur

Panasonic

Panasonic PT-RZ370E Manuel utilisateur

Panasonic

Panasonic PT-FW300E Manuel utilisateur

Panasonic

Panasonic PT-LW373 Mode d'emploi

Panasonic

Panasonic PT-EZ590 Manuel utilisateur

Panasonic

Panasonic PT-AE4000 Manuel utilisateur

Panasonic

Panasonic PT-DS20KU Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur