Panasonic CF-VDM Series Manuel utilisateur

Printed in Japan

HS1006-0

DFQX5638ZA

ENGLISH

OPERATING INSTRUCTIONS

Introduction....................................................5

Handling Precautions....................................6

Using the Drive...............................................8

Using the Software ......................................12

Troubleshooting...........................................18

Speciﬁcations...............................................20

DEUTSCH

BEDIENUNGSANLEITUNG

Einführung....................................................21

Vorsichtsmaßnahmen zum Gebrauch .......22

Gebrauch des Laufwerks ............................24

Gebrauch von Software...............................28

Störungsbehebung......................................34

Technische Daten ........................................36

FRANÇAIS

INSTRUCTIONS D’UTILISATION

Introduction..................................................37

Précautions de manipulation......................38

Utilisation du lecteur ...................................40

Utilisation du logiciel...................................44

Dépannage....................................................50

Spéciﬁcations...............................................52

日本語

取扱説明書

保証書付き（日本国内向け）

はじめに................................................................

安全上のご注意.....................................................

使用上のお願い.....................................................

ドライブを使う.....................................................

ソフトウェアを使う.............................................

困ったときの Q&A..............................................

仕様........................................................................

保証とアフターサービス.....................................

・ この取扱説明書をよくお読みのうえ、正し

くお使いください。特に「安全上のご注意」

（54 ページ）は、ご使用前に必ずお読

みいただき、安全にお使いください。お読

みになった後は、保証書と一緒に大切に保

管し、必要なときにお読みください。

・



保証書は「お買い上げ日・販売店名」などの記

入を確かめ、販売店からお受け取りくださ

い。

DVD MULTI Drive Pack

DVD MULTI ドライブパック

CF-VDM742U

CF-VDM742.indb1CF-VDM742.indb1 2006/09/2615:44:172006/09/2615:44:17

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RA-

DIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

WARNUNG!

DIESES PROUKT ERZEUGT LASERSTAHLUNG.

DURCHFÜHRUNG ANDERER VORGÄNGE ALS DER HIER ANGEGEBENEN

KANN ZU GEFÄHRLICHER STRAHLUNG FÜHREN.

REPARATUREN DÜRFEN NUR VON QUALIFIZIERTEM FACHPERSONAL

DURCHGEFÜHRT WERDEN.

AVERTISSEMENT!

CET APPAREIL UTILISE UN LASER.

L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU L’EXÉCUTION DE

PROCÉDURES AUTRES QUE CELLES SPÉCIFIÉES ICI PEUVENT PROVOQUER

UNE EXPOSITION À DES RADIATIONS DANGEREUSES.

NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE RÉPARER SOI-MÊME.

CONFIER TOUT TRAVAIL D’ENTRETIEN À UN PERSONNEL QUALIFIÉ.

注意！

本装置はレーザ利用機器です。

ご注意 - ここに規定した以外の手順による制御や調整は、危険なレーザ放射の被

曝をもたらします。分解や修理は行わないでください。

CLASS 1 LASER PRODUCT

LASER KLASSE 1

02CF-VDM742.indd202CF-VDM742.indd2 2006/09/2214:44:482006/09/2214:44:48

For U.S.A.

Federal Communications Commission Radio Frequency Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a particular instal-

lation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiv-

er is connected.

Consult the Panasonic Service Center or an experienced radio/TV technician for help.

Warning

To assure continued compliance, use only shielded interface cables when connecting to a

computer or peripheral. Also, any changes or modiﬁcations not expressly approved by the

party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

This device is Class B veriﬁed to comply with Part 15 of FCC Rules when used with Pan-

asonic Notebook Computer.

Responsible Party: Panasonic Corporation of North America

One Panasonic Way

Secaucus, NJ 07094

Tel No:1-800-LAPTOP5 (1-800-527-8675)

For Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

02CF-VDM742.indd302CF-VDM742.indd3 2006/09/2214:44:482006/09/2214:44:48

Compliance Notice - CE Mark

This equipment is in conformance with the requirements of the European Council Direc-

tive

listed below:

73/23/EEC Low Voltage Directive with amendment 93/68/EEC

89/336/EEC EMC Directive with amendments 92/31/EEC and 93/68/EEC

Übereinstimmungserklärung - CE-Marke

Diese Ausrüstung erfüllt die Anforderungen der unten angegebenen EC-Direktive:

73/23/EEC Niederspannungsdirektive mit Abänderung 93/68/EEC

89/336/EEC EMC-Direktive mit Abänderungen 92/31/EEC und 93/68/EEC

Avis de comformité - Marque CE

Cet équipement est conforme aux conditions des Directives de la Commission européenne

mentionnées ci-dessous:

73/23/EEC Directive sur la basse tension y compris la modiﬁcation 93/68/EEC

89/336/EEC Directive CEM y compris les modiﬁcations 92/31/EEC et 93/68/EEC

02CF-VDM742.indd402CF-VDM742.indd4 2006/09/2214:44:482006/09/2214:44:48

Thank you for purchasing the DVD MULTI Drive Pack for the Panasonic CF-74 notebook

computer series*1.

This drive connects to the computer through the multimedia pocket.

Store this manual in a safe place after reading it.

*1For information about the computer(s) for which the DVD MULTI Drive Pack can be used, refer

to the Operating Instructions of your computer, catalogs, etc.

Introduction

Microsoft®and Windows®are registered trademarks of Microsoft Corporation in the United States

and/or other countries.

WinDVD™is a trademark of InterVideo, Inc.

DVD MULTI Drive Pack ...............1 Operating Instructions................1

NOTE

The DVD MULTI Drive Pack may also be referred to as the drive.

In these instructions, the names and terms are referred as follows.

• “WinDVD™ 5 (OEM Version)” as “WinDVD”

• “B’s Recorder GOLD8 BASIC” as “B’s Recorder”

• “B’s CLiP 6” as “B’s CLiP”

This manual explains the procedure for default settings. The procedure may differ

according to the settings.

03CF-VDM742E.indd503CF-VDM742E.indd5 2006/09/2214:45:242006/09/2214:45:24

Handling Precautions

Do not expose the drive to excessive smoke that may leave a residue, e.g., oil smoke, or

tobacco smoke. Doing so can shorten the life of the drive lens.

We recommend cleaning the drive lens with an air puffer used for camera lenses.

(Do not use any spray-type of lens cleaning products.)

When opening/closing the tray

When the computer is on, use the eject button ( page 8) or eject through Windows.

When is displayed on the notiﬁcation area, right-click and click [Eject] to eject a

disk.

Eject disks only as described above.

When inserting or removing a disk, be careful not to touch the lens of the drive.

Do not leave the tray open and do not touch the lens.

The lens and disk can become dusty in some conditions. It may cause malfunction in

reading or writing.

Do not apply excessive force to the tray in the open position.

Never insert a foreign object such as a paper clip into the drive.

Doing so may cause malfunction.

Do not place items other than disks on the tray.

Do not access the drive until after the tray is closed and the multimedia pocket device

indicator is off.

While the drive is being accessed

Do not open the drive or move the computer while the drive is being accessed.

Doing so could cause the disk to shift position and this may damage the disk, or cause

the drive to malfunction.

In addition, after running an application involving access to a disk, close the application

before opening the drive or removing the disk.

Drive Handling Care

Do Not Look Into the CD/DVD Drive

Looking directly at the internal laser light source may result in damage to eyesight.

Do Not Use Disks That Are Cracked or Deformed

Because the disks rotate at high speeds, damaged disks may break apart causing injury.

Disks that are not round and disks that have been repaired using adhesives are similarly

dangerous, and so should not be used.

CF-VDM742.indb6CF-VDM742.indb6 2006/09/2615:44:182006/09/2615:44:18

Do not use deformed, warped, or irregularly shaped disks.

Reading of disk may not be possible depending on the disk conditions (cracks, dirt,

modiﬁcation, data recording quality, copy protection, recording equipment/software that

was used to create the disk, etc.)

Before using a disk, carefully read the operating/handling instructions and package of

the disk.

If the disks are not handled appropriately, they may become dirty or scratched. Further-

more the writing speed may get slower and the data may not be correctly written on or

read from the disk. Other damage may cause a drive failure.

Note the following precautions.

• Do not touch the disk surface (the side with no printing).

• Keep the disk surface clean and free from dirt, dust, ﬁngerprints and scratches.

• Do not write on the surface of the disk with a ballpoint pen or other writing instrument.

• Do not attach stickers to disks.

• Do not drop, bend, or place heavy objects on top of disks.

•

Do not place or store disks in locations exposed to heat, direct sunlight, humidity or

dust.

• If a disk is brought from a cold to a warm location, condensation may form on the

disk. For read-only disks, wipe off the condensation using a soft, dry, lint-free cloth be-

fore using the disk. For recordable/rewritable disks, wait until the condensation dries.

•When not using disks, keep them in their protective cases or cartridges.

To clean disks

Wipe disks with a dry, soft cloth from

the center toward the edge.

If disks get very dirty, wipe with a

moist, soft cloth from the center toward the edge, then wipe again with a dry cloth to

take up remaining moisture.

Use the Panasonic disk cleaner to clean these disks.

Do not use a cloth, CD cleaners or any other such cleaners under any circumstances.

How to hold a disk

Disk Handling Care

CF-VDM742.indb7CF-VDM742.indb7 2006/09/2615:44:182006/09/2615:44:18

Using the Drive

Refer to “Multimedia Pocket” in the Reference Manual included with your computer for

details on how to insert and remove the drive.

Inserting/Removing the Drive

Preparations

Conﬁrm that [Transfer Mode] is set to [DMA if available] in [start] - [Control Panel] -

[Performance and Maintenance] - [System] - [Hardware] - [Device Manager] - [IDE ATA/

ATAPI controllers] - [Primary IDE Channel] - [Advanced Settings] - [Device 0]. Perform

this setting if it has not yet been made.

Turn on the computer.

Press the eject button (A) and slowly

pull out the tray.

Insert/Remove the disk.

To insert

Set the disk with the label side up and press the

center of the disk until it clicks in place.

To remove

Press on the center spindle (B) and carefully lift up the edge of the disk.

Close the tray.

Do not press the eject button.

Setting a Disk

NOTE

To remove a disk when the computer is powered off, insert a pointed object (e.g.,

the bent-out tip of a paper clip, or the tip of a pencil or ballpoint pen) into the emer-

gency hole (C). Pushing it to the end allows the tray to come out. (The position of

the emergency hole depends on the drive.)

If the vibration of the drive is excessive, check the disk. If the disk is normal and is

inserted correctly, set [CD/DVD Drive Speed] to [Low] in the [Main] menu of the

Setup Utility ( Reference Manual “Setup Utility”).

When using B’s Recorder, select writing speed [8x] or less to minimize vibration.

For AutoPlay CD:

•

If an AutoPlay CD does not start after the computer resumes from standby or hiber-

nation, remove the disk from the drive and then reinsert it after waiting 15 seconds.

• An AutoPlay CD may start during ﬁle access depending on the status of the disk.

When playing back video from a disk, playback may not be smooth in some condi-

tions.

CF-VDM742.indb8CF-VDM742.indb8 2006/09/2615:44:182006/09/2615:44:18

Information

NOTE

[Conﬁrm Region] appears when the DVD-Video has only one region code and the

drive is set for another region code.

([Conﬁrm Region] may not appear with some DVD-Video disks. To check the cur-

rent region code and the number of remaining times of changing the code, right-

click on the WinDVD screen and click [Setup] - [Region].)

You can change the region code setting up to ﬁve times including the initial setting.

Be extremely careful because you cannot change the region code anymore after the

ﬁfth change, even if you reinstalled the operating system.

Any problem resulting from illegal changing or altering of the region code is the

user’s responsibility.

CAUTION

If the drive is not accessed for 30 seconds, the drive motor will automatically be shut

down to reduce the power consumption. When the drive is accessed again, the drive motor

is turned on. In this case, reading of the disk data will take approximately 30 seconds.

Power-saving Mode

To play DVD-Video or MPEG2 ﬁles;

Use “WinDVD” preinstalled in the computer.

Region Code Setting

DVD-Video are allocated to region codes according to where they are sold. To play a

DVD-Video, the player’s software and the drive must have the corresponding region code.

e.g.,

For U.S.A. and Canada: “1”

For Europe: “2”

The region code of the drive is not set at purchase. The operation depends on the DVD-

Video that is ﬁrst played.

• DVD-Video with a speciﬁc region code:

The drive will automatically be set at the same region code as the DVD-Video.

•DVD-Video with multiple region codes:

[Conﬁrm Region] appears. Select the region code and click [OK]. Play now begins.

CF-VDM742.indb9CF-VDM742.indb9 2006/09/2615:44:182006/09/2615:44:18

Using the Drive

Writing to Disks

Read the instructions on the disk package carefully.

With DVD-RAM, you can write or rewrite as with the hard disk using Explorer, without

using the writing software. (DVD-RAM driver is required. Refer to page 13 on how to

install the software.)

Writing software is required to write data to a disk other than DVD-RAM.

Use “B’s Recorder” and “B’s CLiP” preinstalled in the computer.

Be sure to use disks conforming to the proper write speeds. ( page 20)

If the write operation is to involve a long period of time, be sure to connect the AC

adaptor. If the battery power runs low and the power of the computer is cut, the write

operation may end in failure.

You can read from/write to the following disks.

You can read from the following disks.

*1 DVD-RAM: Only non-cartridge type or removable cartridge type can be used.

*2 Does not support DVD-RW Ver.1.0.

CF-VDM742.indb10CF-VDM742.indb10 2006/09/2615:44:182006/09/2615:44:18

Autres manuels pour CF-VDM Series

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Panasonic Lecteur DVD

Panasonic

Panasonic CF-VDD723M Manuel utilisateur

Panasonic

Panasonic VW-BN1PP Manuel utilisateur

Panasonic

Panasonic CF-VDM302AT Manuel utilisateur

Panasonic

Panasonic CF-VDM Series Manuel utilisateur

Panasonic

Panasonic LF-D201U Manuel utilisateur

Panasonic

Panasonic CF-VDD731 Manuel utilisateur

Panasonic

Panasonic SR-8588-B Manuel utilisateur

Panasonic

Panasonic CF-VDM Series Manuel utilisateur

Panasonic

Panasonic CF-VDM293U Manuel utilisateur

Panasonic

Panasonic CF-VDR301U Manuel utilisateur

Panasonic

Panasonic CF-VDD271W Manuel utilisateur

Panasonic

Panasonic CF-VDD712M Manuel utilisateur

Panasonic

Panasonic CF-VDD372M Manuel utilisateur

Panasonic

Panasonic CF-VDD285 Manuel utilisateur

Panasonic

Panasonic DMRE55P Manuel utilisateur

Panasonic

Panasonic CF-VDR282 Manuel utilisateur

Panasonic

Panasonic FZ-VDM401 Series Manuel utilisateur

Panasonic

Panasonic CF-VDD272 Manuel utilisateur

Panasonic

Panasonic CF-VDM Series Manuel utilisateur

Panasonic

Panasonic LFD521U - DISK DRIVE Manuel utilisateur

Panasonic

Panasonic CF-VDD711W Manuel utilisateur

Panasonic

Panasonic LF-D321U Manuel utilisateur

Panasonic

Panasonic FZ-VDR551 Series Manuel utilisateur

Panasonic

Panasonic CW-8572-B Manuel utilisateur

Manuels Lecteur DVD populaires d'autres marques

LG GSA-4160B Manuel utilisateur

Sony

Sony DRU-500AX Manuel utilisateur

LG GSA-2164D Manuel utilisateur

Plextor

Plextor PX-755SA Manuel utilisateur

Pioneer

Pioneer BDC-TD03RS Manuel du propriétaire

Samsung

Samsung SM-332B Manuel utilisateur

Freecom

Freecom MOBILE DVD RW II Manuel utilisateur

Plextor

Plextor PX-712 Manuel utilisateur

NEC

NEC ND-3550A Manuel utilisateur

Emprex

Emprex Slim Writer DVD R/RW USB 2.0 External Drive Manuel utilisateur

Philips

Philips PCA532K Manuel utilisateur

Sony

Sony AD-7740H Manuel utilisateur

Philips

Philips PCDV5016 Series Guide de référence

Pioneer

Pioneer LaserMemory DVD-115 Manuel utilisateur

Samsung

Samsung SE-S224Q Manuel utilisateur

IBM

IBM 71P7285 Manuel utilisateur

Pioneer

Pioneer DVR-A04 Manuel utilisateur

IBM

IBM 27L2579 Manuel utilisateur