Panasonic CF-VDM302AT Manuel utilisateur

Printed in Japan

DVD MULTI Drive Pack

DVD MULTI-Laufwerk-Pack

Lecteur DVD MULTI

DVD MULTI 驱动器

DVD 多功能光碟機組

DVD 멀티 드라이브 팩

DVD MULTI 

Model No. / Modell-Nr. / Numéro de modèle / 型号 / 型號/ 모델번호 / 

CF-VDM302AT

SS0211-0 DFQW5494ZA

*DFQW5494ZA*

操作指示 ..........................46

OPERATING INSTRUCTIONS ..........6

繁體中文

ENGLISH

사용 설명서 .......................56

한국어

BEDIENUNGSANLEITUNG ...........16

DEUTSCH

MODE D’EMPLOI...................26

FRANÇAIS

使用说明书 ........................36

简体中文

取扱説明書 ........................66

日本語

保証書付き（日本国内向け）

・取扱説明書をよくお読みのうえ、正しく安全にお使いください。

・ご使用前に「安全上のご注意」（ 67 ページ）を必ずお読みくだ

さい。

・保証書は「お買い上げ日・販売店名」などの記入を確かめ、取扱説

明書とともに大切に保管してください。

CF-VDM302AT.indb 1 2011/02/28 15:31:01

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RA-

DIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

12-E-1

WARNUNG!

DIESES PROUKT ERZEUGT LASERSTAHLUNG.

DURCHFÜHRUNG ANDERER VORGÄNGE ALS DER HIER ANGEGEBENEN

KANN ZU GEFÄHRLICHER STRAHLUNG FÜHREN.

REPARATUREN DÜRFEN NUR VON QUALIFIZIERTEM FACHPERSONAL

DURCHGEFÜHRT WERDEN.

12-G-1

AVERTISSEMENT!

CET APPAREIL UTILISE UN LASER.

L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU L’EXÉCUTION DE

PROCÉDURES AUTRES QUE CELLES SPÉCIFIÉES ICI PEUVENT PROVOQUER

UNE EXPOSITION À DES RADIATIONS DANGEREUSES.

NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE RÉPARER SOI-MÊME.

CONFIER TOUT TRAVAIL D’ENTRETIEN À UN PERSONNEL QUALIFIÉ.

12-F-1

CLASS 1 LASER PRODUCT

LASER KLASSE 1

CF-VDM302AT.indb 2 2011/02/28 15:31:01

CLASS 1 LASER PRODUCT

LASER KLASSE 1

注意！

本產品使用雷射。

非本說明指定之使用、操控、調整行為，可能導致危險輻射曝露。勿開啟頂蓋或自

行嘗試修理。

請交由合格專業人員為您服務。

주의 !

본 제품은 레이저를 사용합니다 .

본 지침에서 지징하지 않은 제어장치나 조절장치의 사용또는 절차의 수행은 위험

한 방출을 초래할 수 있습니다 .

커버를 얼가나 스스로 수리를 시도하지 마십시오 .

서비스는 자걱이 있는 사람에게 위임하십시오 .

本装置はレーザー利用機器です。

ご注意 - ここに規定した以外の手順による制御や調整は、危険なレーザー放射の

被爆をもたらします。

分解や修理は行わないでください。

14-J-1-1

注意事项 !

本产品为使用激光制品。

按本处规定外使用各种控制器、调节或操作步骤可能造成危险的辐射照射。

切勿打开机盖，不要自行进行修理。

请有资格的人进行维修。 12-Cs-1

CF-VDM302AT.indb 3 2011/02/28 15:31:01

For U.S.A.

Federal Communications Commission Radio Frequency Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a particular instal-

lation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiv-

er is connected.

Consult the Panasonic Service Center or an experienced radio/TV technician for help.

Warning

To assure continued compliance, use only shielded interface cables when connecting to a

computer or peripheral. Also, any changes or modications not expressly approved by the

party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

This device is Class B veried to comply with Part 15 of FCC Rules when used with Pan-

asonic Notebook Computer.

Responsible Party: Panasonic Corporation of North America

One Panasonic Way

Secaucus, NJ 07094

Tel No:1-800-LAPTOP5 (1-800-527-8675)

6-M-1

USA Only: Disposal may be regulated in your community due to environmental consid-

erations. For disposal or recycling information, please visit Panasonic website:

http://www.panasonic.com/environmental or call 1-888-769-0149

65-M-2

CF-VDM302AT.indb 4 2011/02/28 17:03:10

For Canada

Canadian ICES-003

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

7-M-2

CF-VDM302AT.indb 5 2011/02/28 15:31:01

Thank you for purchasing Panasonic Product*1.

This drive connects to the computer through the multimedia pocket.

Please read these instructions carefully before using this product, and save this manual for

future use.

*1For information about the computer(s) for which the DVD MULTI Drive Pack can be used, refer

to the catalogs, etc.

Introduction

Microsoft®, Windows®and Windows Vista are registered trademarks of Microsoft Corporation in the

United States and/or other countries.

Accessories Operating Instructions (This book)................... 1

NOTE

The DVD MULTI Drive Pack may also be referred to as the drive.

This manual explains the procedure for default settings. The procedure may differ

according to the settings.

Windows 7 indicates Genuine Windows® 7 Professional Operating System.

Windows Vista indicates Genuine Windows Vista® Business Operating System.

Windows XP indicates Genuine Microsoft® Windows® XP Professional

Operating System.

: Page in these Operating Instructions or in the Reference Manual.

: Refers to the on-screen manuals.

CF-VDM302AT.indb 6 2011/02/28 15:31:01

Handling Precautions

Do not expose the drive to excessive smoke that may leave a residue, e.g., oil smoke, or

tobacco smoke. Doing so can shorten the life of the drive lens.

We recommend cleaning the drive lens with an air puffer used for camera lenses.

(Do not use any spray-type of lens cleaning products.)

When opening/closing the tray

When the computer is on, use the eject button ( page 9) or eject through Windows.

When inserting or removing a disc, be careful not to touch the lens of the drive.

Do not leave the tray open and do not touch the lens and other parts of the laser pickup.

The laser pickup and disc can become dusty in some conditions. It may cause

malfunction in reading or writing.

Do not apply excessive force to the tray in the open position.

Never insert a foreign object such as a paper clip into the drive.

Doing so may cause malfunction.

Do not place items other than discs on the tray.

Do not access the drive until after the tray is closed and the multimedia pocket device

indicator is off.

While the drive is being accessed

Do not open the tray or move the computer while the drive is being accessed.

Doing so could cause the disc to shift position and this may damage the disc, or cause

the drive to malfunction.

In addition, after running an application involving access to a disc, close the application

before opening the tray or removing the disc.

●

Drive Handling Care

Do Not Look Into the Drive

Looking directly at the internal laser light source may result in damage to eyesight.

Do Not Use Discs That Are Cracked or Deformed

Because the discs rotate at high speeds, damaged discs may break apart causing injury.

Discs that are not round and discs that have been repaired using adhesives are similarly

dangerous, and so should not be used.

●

CF-VDM302AT.indb 7 2011/02/28 15:31:01

Before using a disc, carefully read the operating/handling instructions and package of

the disc.

If the discs are not handled appropriately, they may become dirty or scratched.

Furthermore the writing speed may get slower and the data may not be correctly written

on or read from the disc. Other damage may cause a drive failure.

Note the following precautions.

Do not touch the disc surface (the side with no printing).

Keep the disc surface clean and free from dirt, dust, ngerprints and scratches.

Do not write on the surface of the disc with a ballpoint pen or other writing instrument.

Do not attach stickers to discs.

Do not drop, bend, or place heavy objects on top of discs.

Do not place or store discs in locations exposed to heat, direct sunlight, humidity or dust.

If a disc is brought from a cold to a warm location, condensation may form on the disc.

For read-only discs, wipe off the condensation using a soft, dry, lint-free cloth before

using the disc. For recordable/rewritable discs, wait until the condensation dries.

When not using discs, keep them in their protective cases or cartridges.

●

•

To clean discs

Wipe discs with a dry, soft cloth from

the center toward the edge.

If discs get very dirty, wipe with a

moist, soft cloth from the center toward the edge, then wipe again with a dry cloth

to take up remaining moisture.

Use the recordable/rewritable disc cleaner to clean these discs.

Do not use a cloth, CD cleaners or any other such cleaners under any circumstances.

Disc Handling Care

Handling Precautions

How to hold a disc

CF-VDM302AT.indb 8 2011/02/28 15:31:01

Using the Drive

For details on how to insert and remove the drive, refer to “Multimedia Pocket” in the

Reference Manual included with your computer.

Inserting/Removing the Drive

Preparations

Windows 7

1Click (Start) - [Computer] - [System properties] - [Device Manager].

2Click [View] - [Devices by connection] - [ACPIx86-based PC] - [Microsoft ACPICom-

pliant System] - [PCIbus] - [Intel(R) ICH9M/M-E Family 4 Port SATA AHCI Control-

ler - 2929], double-click [ATA Channel 0], and click [Advanced Settings].

3 Conrm that the check mark has been added for [Enabled DMA]. If it has not, add the

check mark and click [OK].

Windows Vista

1Click (Start) - [Control Panel] - [System and Maintenance] - [System] - [Device

Manager].

A standard user needs to enter an administrator password.

2<Only for CF-30 C/D/E/F/G/J series>

Click [View] - [Devices by connection] - [ACPIx86-based PC] - [Microsoft ACPI-

Compliant System] - [PCIbus] - [Intel(R)82801G(ICH7 Family) Ultra ATA Storage

Controllers - 27DF], double-click [ATA channel 0], and click [Advanced Settings].

Click [View] - [Devices by connection] - [ACPIx86-based PC] - [Microsoft ACPI-

Compliant System] - [PCIbus] - [Intel(R) ICH9 Family PCI Express Root Port2 - 2942]

- [Standard Dual Cannel PCI IDE Controller], double-click [ATA channel 0], and click

[Advanced Settings].

3 Conrm that the check mark has been added for [Enabled DMA]. If it has not, add the

check mark and click [OK].

Windows XP

Conrm that [Transfer Mode] is set to [DMA if available] in [start] - [Control Panel] -

[Performance and Maintenance] - [System] - [Hardware] - [Device Manager] - [IDE ATA/

ATAPI controllers] - [Primary IDE Channel] - [Advanced Settings] - [Device 0]. Perform

this setting if it has not yet been made.

1Turn on the computer.

2Slide the latch (A) and open the

cover.

3Press the eject button (B) and slowly

pull out the tray.

Setting a Disc

CF-VDM302AT.indb 9 2011/02/28 15:31:01

NOTE

To remove a disc when the computer is powered off, insert a pointed object (e.g.,

the bent-out tip of a paper clip) into the emergency hole (D). Pushing it to the end

allows the tray to come out.

If the vibration of the drive is excessive, check the disc. If the disc is normal and is

inserted correctly, set [DVD Drive Speed] to [Low] in the [Main] menu of the Setup

Utility ( Reference Manual “Setup Utility”).

For AutoPlay CD:

If an AutoPlay CD does not start after the computer resumes from sleep*1 or

hibernate, remove the disc from the drive and then reinsert it after waiting 15 seconds.

An AutoPlay CD may start during le access depending on the status of the disc.

When playing back video from a disc, playback may not be smooth in some conditions.

*1Windows XP standby

•

If the drive is not accessed for 30 seconds, the drive motor will automatically be shut

down to reduce the power consumption. When the drive is accessed again, the drive motor

is turned on. In this case, reading of the disc data will take approximately 30 seconds.

Power-saving Mode

Using the Drive

Insert/Remove the disc.

To insert

Set the disc with the label side up and press the

center of the disc until it clicks in place.

To remove

Press on the center spindle (C) and carefully lift

up the edge of the disc.

Close the tray.

Do not press the eject button.

CF-VDM302AT.indb 10 2011/02/28 15:31:02

Table des matières

Langues :

Autres manuels Panasonic Lecteur DVD

Panasonic

Panasonic CF-VDD712M Manuel utilisateur

Panasonic

Panasonic CF-VDM302AU Manuel utilisateur

Panasonic

Panasonic SR-8589-B Manuel utilisateur

Panasonic

Panasonic SW-9501-S Manuel utilisateur

Panasonic

Panasonic FZ-VDM551 Series Manuel utilisateur

Panasonic

Panasonic FZ-VDM401 Series Manuel utilisateur

Panasonic

Panasonic LF-M621U Manuel utilisateur

Panasonic

Panasonic CF-VDM Series Manuel utilisateur

Panasonic

Panasonic CF-VDD271W Manuel utilisateur

Panasonic

Panasonic SR-8588-B Manuel utilisateur

Panasonic

Panasonic VW-BN1 - DVD-RW / DVD-RAM Drive Manuel utilisateur

Panasonic

Panasonic SR-8587-B Manuel utilisateur

Panasonic

Panasonic CF-VDR301U Manuel utilisateur

Panasonic

Panasonic VW-BN1PP Manuel utilisateur

Panasonic

Panasonic LF-D201U Manuel utilisateur

Panasonic

Panasonic CF-VDR302U Manuel utilisateur

Panasonic

Panasonic CF-VDD285M Manuel utilisateur

Panasonic

Panasonic VW-BN1 - DVD-RW / DVD-RAM Drive Manuel utilisateur

Panasonic

Panasonic KXL-CB30AU Manuel utilisateur

Panasonic

Panasonic CF-VDR721M Manuel utilisateur

Panasonic

Panasonic CF-VDRRT3W Manuel utilisateur

Panasonic

Panasonic CF-VDR282 Manuel utilisateur

Panasonic

Panasonic CF-VDM302U Manuel utilisateur

Panasonic

Panasonic CF-VDD281 Manuel utilisateur

Manuels Lecteur DVD populaires d'autres marques

LG GSA-4160B Manuel utilisateur

Sony

Sony DRU-500AX Manuel utilisateur

LG GSA-2164D Manuel utilisateur

Plextor

Plextor PX-755SA Manuel utilisateur

Pioneer

Pioneer BDC-TD03RS Manuel du propriétaire

Samsung

Samsung SM-332B Manuel utilisateur

Freecom

Freecom MOBILE DVD RW II Manuel utilisateur

Plextor

Plextor PX-712 Manuel utilisateur

NEC

NEC ND-3550A Manuel utilisateur

Emprex

Emprex Slim Writer DVD R/RW USB 2.0 External Drive Manuel utilisateur

Philips

Philips PCA532K Manuel utilisateur

Sony

Sony AD-7740H Manuel utilisateur

Philips

Philips PCDV5016 Series Guide de référence

Pioneer

Pioneer LaserMemory DVD-115 Manuel utilisateur

Samsung

Samsung SE-S224Q Manuel utilisateur

IBM

IBM 71P7285 Manuel utilisateur

Pioneer

Pioneer DVR-A04 Manuel utilisateur

IBM

IBM 27L2579 Manuel utilisateur