Overland Storage SnapServer XSD 40 Manuel utilisateur

*10400570001*

SnapServer®XSD 40

Chassis Replacement Instructions

This document describes how to swap out the chassis of a

SnapServer XSD 40 from Overland Storage.

WARNING: To reduce the risk of electric shock or damage to

equipment, always remove any power cords while working

with the unit.

AVERTISSEMENT: Pour réduire le risque de choc électrique

ou endommagement de l'équipement, retirez toujours les

cordons électriques en travaillant avec l'appareil.

CAUTION: While working with the unit, observe standard

Electrostatic Discharge (ESD) precautions to prevent damage

to micro-circuitry or static-sensitive devices.

Prepare the Unit

Power Off and Disconnect Cables

1. Briefly press the Power button on the front.

2. When all the front LEDs are off, disconnect the power

cord.

3. Disconnect all the cables from the unit.

Remove the Drives

NOTE: Do not remove the disk drives from their carriers. Doing so

voids the drive warranty.

1. Slide the release button to the right. The latch on the

front of the carrier will release and the handle will extend.

2. Using the handle, pull the carrier out.

3. Set the carrier on a secure surface.

4. Repeat Steps 1–3 for each remaining carrier.

Power

Cables

Press Right

Pull Carrier

Chassis Replacement Instructions

Transfer Components

Remove the Side Panels

All installed components, such as DIMMs and PCIe cards, need

to be transferred to the new chassis. DIMMs are accessed

through the right-side panel (when facing the unit front); the

PCIe card is accessed via the left-side panel.

NOTE: The right- and left-side panels are interchangeable.

1. On the back of the unit, remove and retain the right-side

thumb screw securing the side panel.

2. Slide the side panel towards the back of the unit until the

anchors release and the panel is free.

3. Set the panel on a secure surface.

4. If an optional PCIe card is installed, repeat Steps 1–3

for the left-side panel.

Move DIMMs

DIMMs are accessed via the right side of the unit. All installed

DIMMs should be transferred to the new chassis:

NOTE: Carefully move all cabling aside while installing and

removing components.

1. Remove the DIMMs from the old chassis by pressing the

latches on each end and popping the DIMMs out.

2. In the new chassis, slide the DIMM into the lowest

DIMM slot, lining up the DIMM notch with the guide in

the slot.

3. Firmly press the DIMM down until it latches in place.

4. Do one of the following:

•If there are two DIMMs installed, repeat Steps 2–3, to

seat the second DIMM in the remaining slot.

•If there is only one DIMM installed, go to “Reinstall

the Side Panels.”

Right-side Thumb Screw

Left-side Thumb Screw

DIMM Slot

DIMM

Chassis Replacement Instructions

Move the Optional PCIe Card

NOTE: If there is no PCIe card installed in the old chassis, skip to

“Reinstall the Side Panels.”

. The PCIe card is accessed via the left side of the unit.

NOTE: Carefully move all cabling aside while installing and

removing components.

1. In the new chassis, remove the slot cover:

a. Remove the screw securing the slot cover to the locking

bracket.

b. Remove the locking bracket by loosening the screw

securing the bracket.

c. Retain both screws, the locking bracket, and cover.

2. In the old chassis, remove the PCIe card:

a. Remove and retain the screw securing the PCIe card to

the locking bracket

b. Remove the locking bracket by loosening the screw

securing the bracket.

c. Remove the PCIe card by pulling it straight up from

the board and out of the unit.

3. In the new chassis, install the PCIe card:

a. Seat the PCIe card in the same slot on the new board

and the back panel of the chassis.

b. Reinstall the locking bracket and tighten the screw

to secure the PCIe card.

c. Thread the screw through the PCIe card bracket to

secure the card to the locking bracket.

Reassemble the Unit

Reinstall the Side Panels

NOTE: The panels are interchangeable; if you are having issues,

reverse the orientation of the panel. When correctly installed, the

side panels will slightly overlap the back of the unit.

1. On the new chassis, position the side panel with no more

than one-half inch (1.25 cm) extending out over the rear

of the unit.

2. Align the tabs on top and bottom of the panel with the

slots on the side of the unit.

3. Slide the panel towards the front of the unit, ensuring the

tabs are seated securely in the slots. The panel will click

into place.

4. Reinstall the thumb screw on the back of the unit to

secure the panel.

5. If needed, repeat Steps 1–4 to reinstall the second panel.

Screw

Slot Cover

Locking Bracket Screw

PCIe Slot

http://support.overlandstorage.com

You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using

the information found on the Contact Us page on our web site.

Chassis Replacement Instructions

Reinstall the Carriers

Return the drive carriers to their original bays.

1. Position a drive carrier assembly in front of its empty

bay.

2. Slide the assembly into the bay until it stops.

3. Swing the handle closed until it locks (clicks) into place.

4. Repeat Steps 1–3 for all remaining drive carriers.

5. Close the door.

Attach Cables and Power Cord

1. Reattach all the cables (except the power cord) to the

same connections previously used.

2. Attach the power cord.

3. At the front, press the power button to power it ON.

IMPORTANT: If this is a new appliance install, continue with

the SnapServer XSD 40 Quick Start Guide instructions.

Complete the Exchange

Validate the System

1. Log onto the system and verify both the connections and

settings.

2. Check the front LEDs for flashing indicating errors.

If there are any problems, contact Overland Technical

Support:

http://docs.overlandstorage.com/support

Return Old Chassis to Overland

1. Place the old chassis in the anti-static bag and put it in

the replacement part’s box.

2. Use an RMA to return the part to Overland Storage.

For return shipping details and RMA number, go to:

http://docs.overlandstorage.com/return-instructions

Slide Carrier

Power

Cables

Autres manuels pour SnapServer XSD 40

Table des matières

Autres manuels Overland Storage Stockage

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage SnapServerXSR 40 Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage REO 4500x Manuel utilisateur

Overland Storage

Overland Storage Neo Series Library Manuel utilisateur

Overland Storage

Overland Storage REO 1000 Manuel utilisateur

Overland Storage

Overland Storage NEO Series Manuel utilisateur

Overland Storage

Overland Storage NEO Series Manuel utilisateur

Overland Storage

Overland Storage REO Series Manuel utilisateur

Overland Storage

Overland Storage ULTAMUS Manuel

Overland Storage

Overland Storage NEO 8000E Manuel utilisateur

Overland Storage

Overland Storage ARCvault Series Manuel utilisateur

Overland Storage

Overland Storage NEO 8000E Manuel utilisateur

Overland Storage

Overland Storage ARCvault Series Manuel utilisateur

Overland Storage

Overland Storage NEO 400S Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage NEO 200S Manuel utilisateur

Overland Storage

Overland Storage NEO 200S Manuel utilisateur

Overland Storage

Overland Storage SnapServer XSD 40 Manuel utilisateur

Overland Storage

Overland Storage NEOxl 40 Manuel utilisateur

Overland Storage

Overland Storage SnapServer DX1 Manuel utilisateur

Overland Storage

Overland Storage NEO 8000E Manuel utilisateur

Overland Storage

Overland Storage NEO 2000e Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur