Overland Storage NEO Series Manuel utilisateur

*10400535-001*

NEO®Tape Libraries

Spare Drive Fan Assembly Instructions

This document describes how to remove and replace the drive

fan assembly on a SCSI tape drive assembly in a NEO tape

library from Overland Storage.

NOTE: While these instructions can be used to change the fan

assemble on any LTO NEO drive assembly, they are also used as

part of the instructions to convert drive assemblies from a legacy

U320 SCSI hot-swap PWA to a SCSI direct-connect PWA.

CAUTION: While working with the unit, observe standard

Electrostatic Discharge (ESD) precautions to prevent damage

to micro-circuitry or static-sensitive devices.

Remove the Tape Drive Assembly

Deactivate and Disconnect

1. Unload any cartridge in the drive being removed.

Use either the backup application software or the NEO

Web Management Interface.

2. Verify there is no activity to the drive from the host.

3. Deactivate the drive being replaced:

At the Front Panel, press Menu > Maintenance >

Replace Drive > Deactivate Drive n.

4. At the rear, locate the drive assembly.

5. Remove the data cable and SCSI terminator from the

drive housing (or the connectors below it for legacy drives).

6. Loosen the thumbscrews at the top and bottom.

7. Fully supporting the drive assembly underneath, pull

the handle to remove it.

NOTE: Some effort may be required to overcome the initial

resistance of unplugging the module from the receiver.

8. Place the drive assembly on a secure surface on its side

with the right side up.

CAUTION: Use care in handling the assembly as not to

bend the thumbscrew tabs.

9. Unpack the new fan assembly and place it on the secure

surface with the drive assembly.

Legacy Drive:

Direct Connect Drive:

Thumbscrews

SCSI Connectors

Spare Drive Fan Assembly Instructions

Swap Out Fan Assemblies

Remove the Old Fan Assembly

1. Remove and retain the three screws and washers

holding the old fan assembly to the drive assembly.

2. Gently pull the fan assembly away from the tape drive

about 1 inch (2.5cm).

CAUTION: Use care not to put a strain on the cables

connecting the drive to the assembly.

3. Carefully unplug the fan cable from the interconnector

board at the bottom.

4. Next, carefully unplug the SCSI interface cable from the

back of the drive.

5. For an older legacy drive assembly, also unplug the

other end of the SCSI cable from the interconnector

board and set it aside.

NOTE: The new fan assembly has the SCSI cables already in it

as part of the direct-connect design.

6. Remove the old fan assembly and set aside.

Install the New Fan Assembly

1. Position the new fan assembly in front of the drive

assembly about 1 inch (2.5cm) away.

2. Carefully connect the dual SCSI interface cable from

the fan assembly to the drive.

The wider part of the plug should be at the bottom to

match the connector.

3. With the fan assembly positioned close to the drive

assembly, carefully plug the fan plug into its port.

4. Carefully slide the two assemblies together until you can

see the screw holes aligned.

5. Using the three retained screws and washers, secure

the fan assembly to the drive assembly.

Be sure to tighten them securely.

Reinstall the Drive Assembly

CAUTION: When inserting the drive assembly, push evenly on

both the handle and the bottom section until it is seated. Do

not lift the drive by the handle while pushing it into the bay.

1. While fully supporting the drive assembly, line it up

with the open bay and slowly push it into the bay until it

seats firmly against the backplane.

2. Tighten the two captive thumbscrews on the tabs.

3. Plug the data cable and SCSI terminator into the

connectors on the drive assembly next to the fan.

NOTE: Do not use the connections below the drive assembly as

they no longer function.

Remove Screws

Fan Connector

Legacy Drive

Direct Connect

SCSI Connector

http://support.overlandstorage.com

You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using

the information found on the Contact Us page on our web site.

Spare Drive Fan Assembly Instructions

Complete the Replacement

Activate the New Drive

Once the drive assembly is in place, it needs to be activated for

the library to recognize it:

•If the Auto Activate feature is enabled, the drive was

automatically activated when it was inserted. No other

actions are needed.

•If the Auto Activate feature is disabled, at the Front

Panel, press Menu > Maintenance > Replace Drive >

Activate Drive n.

The LED on the rear of the new drive flashes green and then

turns solid green when the drive is fully initialized.

NOTE: If you get an amber light, there is a problem with the drive.

Contact Overland Storage Technical Support.

Return Old Parts to Overland

1. Place the old part in the anti-static bag and put it in the

replacement part’s box.

2. Use an RMA to return the part to Overland Storage.

For return shipping details and RMA number, go to:

http://docs.overlandstorage.com/return-instructions

Autres manuels pour NEO Series

Table des matières

Autres manuels Overland Storage Stockage

Overland Storage

Overland Storage NEO 400S Manuel utilisateur

Overland Storage

Overland Storage REO Series Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage NEO S-Series Manuel utilisateur

Overland Storage

Overland Storage NEO 8000E Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Mode d’emploi

Overland Storage

Overland Storage REO 9000 Manuel utilisateur

Overland Storage

Overland Storage NEO 2000e Manuel utilisateur

Overland Storage

Overland Storage Snap Server 210 Manuel utilisateur

Overland Storage

Overland Storage XchangeNOW ARCvault Series Manuel utilisateur

Overland Storage

Overland Storage NEO 4000e Manuel utilisateur

Overland Storage

Overland Storage NEO 2000e Manuel utilisateur

Overland Storage

Overland Storage NEO 4000e Manuel utilisateur

Overland Storage

Overland Storage ARCvault Series Mode d’emploi

Overland Storage

Overland Storage SnapScale X2 Node Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage SnapServer DX2 Manuel utilisateur

Overland Storage

Overland Storage REO 9100 Comment utiliser

Overland Storage

Overland Storage PowerLoader Manuel utilisateur

Overland Storage

Overland Storage SnapServer XSD 40 Manuel utilisateur

Overland Storage

Overland Storage NEO XL Series Manuel

Overland Storage

Overland Storage SnapSAN S3000 Manuel utilisateur

Overland Storage

Overland Storage REO Series Manuel utilisateur

Overland Storage

Overland Storage SnapSAN S1000 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur