Overland Storage NEO 8000 Manuel utilisateur

Introduction

IMPORTANT: Overland Storage requires that all NEO 8000

parts be removed and replaced by an Overland Storage

authorized service provider. Improper installation may

result in damage which voids existing warranties.

The NEO 8000 features LiveSwapTM that, because of the

Hot Swap assembly, permits tape drives to be added,

removed, or replaced without powering down the library.

This document describes how to remove and replace a Hot

Swap assembly in an Overland Storage NEO 8000

Library.

Unpacking the Spare

Carefully unpack the spare part and verify that you have

all the parts:

•Hot Swap assembly in an anti-static bag

•Two M3x6mm screws

•These remove & replace instructions

WARNING: The GUI touch screen does not

completely shut off NEO 8000 system power. To

reduce the risk of electric shock or damage to

equipment, disconnect the power by unplugging

the power cords.

Electrostatic Discharge Information

A discharge of static electricity can damage micro-circuitry

or static-sensitive devices. To help prevent electrostatic

damage, observe the following precautions:

•Transport and store items in static-safe containers.

•Keep electrostatic-sensitive parts in their containers

until they arrive at static-free stations.

•Use a wrist strap and properly-grounded tools.

•Make sure you are always properly grounded when

touching a static-sensitive component or assembly.

•Keep the work area free of non-conductive materials.

•Avoid touching pins, leads, or circuitry.

Prepare the Library

1. At the front panel, power down the library.

2. Set the library circuit breakers to OFF (“O”), and

remove and retain the power cords.

3. Locate the Hot Swap assembly being replaced

(Figure 1).

4. Remove any network cables and terminators.

5. Remove the drives or cover plates from the old

assembly’s drive bay.

6. Remove and retain the M3x8mm screw and drive

divider.

Figure 1. Locations of the Hot Swap Assemblies

NEO 8000 Library

Hot Swap Assembly Spare

Remove & Replace Instructions

Overview & Notes

NEO-8070

Replacing the Hot Swap Assembly

NEO-8105

Hot Swap

Assemblies

Drive

Divider

Screw

Remove Old Assembly

1. Remove the two M2x6mm screws (Figure 2) holding

the assembly to the frame.

Figure 2. Hot Swap Assembly Mounting Screws

2. Gently slide the assembly out about 2 in. (5cm), and

pivot it up to access the cables underneath.

NOTE: If necessary, remove the power and ribbon cables

from the D-clamps on the backplane to make it easier to

remove them from the Hot Swap assembly.

3. Squeezing the sides of the plug to release it, remove the

ribbon cable from the socket.

CAUTION: Failure to release the plug before removing it

damages to the ribbon cable socket.

4. Releasing the clip holding the plug to the socket,

remove the power cable.

5. Remove the old assembly and set it aside.

Install New Assembly

1. Position the new assembly at the drive bay, tilted up

to access the plugs underneath.

2. Run the power cable through the Hot Swap assembly

(Figure 3), and push the plug into the socket until it

clicks in place.

3. Push the ribbon cable plug into the socket until it is

fully seated.

Figure 3. Hot Swap Connections (Bottom View)

4. Slide the assembly back into drive bay until the

alignment pins are in their respective holes.

CAUTION: Verify that the cables do not rub against the edge

of the Hot Swap assembly bottom frame. Verify that the

power and ribbon cables are secured in the D-clamps.

5. Using the new M3x6mm screws, attach the new

assembly to the frame.

Restart the Library

1. Use the retained M3x8mm screw to reinstall the drive

divider.

2. Reinstall the drives or cover plates.

3. Reattach any network cables and terminators.

4. Reattach the power cords and set the library circuit

breakers to ON (“|”).

The library should power up normally and see all drives.

All information contained in or disclosed by this document is considered proprietary by Overland Storage. By accepting this material, the recipient agrees that this material and the information contained therein are

held in confidence and in trust and will not be used, reproduced in whole or in part, nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood that no right is conveyed

to reproduce or have reproduced any item herein disclosed without express permission from Overland Storage. Overland Storage provides this document as is, without warranty of any kind, either expressed or

implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Overland Storage may make improvements or changes in the product(s) or program(s) described

in this document at any time. These changes will be incorporated in new editions of this publication.

Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this document, nor for any problem that might arise from the use of the information in this document.

NEO-8061

M3x6mm

Screws

Drive

Divider

Slot

NEO-8062

Power

Cable

Power

Socket

Alignment

Ribbon

Bottom

D-Clamps

Pin Cable

Path

Frame

Additional Help

You can get additional technical support on the Internet at support.overlandstorage.com,

or call 1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or

001-858-571-5555 x5 (International).

Autres manuels pour NEO 8000

Table des matières

Autres manuels Overland Storage Stockage

Overland Storage

Overland Storage REO 9100 Comment utiliser

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage SnapServer XSD 40 Manuel utilisateur

Overland Storage

Overland Storage NEO 200S Manuel utilisateur

Overland Storage

Overland Storage NEOs T24 Manuel utilisateur

Overland Storage

Overland Storage Tandberg Data RDX QuikStor Manuel utilisateur

Overland Storage

Overland Storage NEO 8000E Manuel utilisateur

Overland Storage

Overland Storage SnapServer XSD 40 Manuel utilisateur

Overland Storage

Overland Storage NEO 200S Manuel utilisateur

Overland Storage

Overland Storage ULTAMUS Manuel

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage Neo Series 2000 Manuel utilisateur

Overland Storage

Overland Storage ULTAMUS RAID 4800 Manuel utilisateur

Overland Storage

Overland Storage NEO Series Manuel utilisateur

Overland Storage

Overland Storage SnapServer Manuel utilisateur

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage REO 9000 Manuel utilisateur

Overland Storage

Overland Storage ARCvault 12 Manuel utilisateur

Overland Storage

Overland Storage NEOs StorageLoader Manuel utilisateur

Overland Storage

Overland Storage ARCvault Series Mode d’emploi

Overland Storage

Overland Storage NEO 8000 Manuel utilisateur

Overland Storage

Overland Storage ARCvault Series Manuel utilisateur

Overland Storage

Overland Storage NEO 8000E Manuel utilisateur

Overland Storage

Overland Storage NEO S-Series Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur