Outback Ranger 3 Manuel utilisateur
Photographs are not to scale.
Specifications subject to change
without prior notice.
Assembly and Operating Instructions for Outback®
Ranger 3 Gas BBQ and Ranger 3S Gas BBQ
WARNING
For outdoor use only. Not for commercial use.
Read instructions before using the appliance. Failure to follow instructions could
result in death, serious bodily injury, and/or property loss.
Warning: accessible parts may be very hot. Keep young children and pets away.
Do not move the appliance during use.
Turn off the gas supply at the gas bottle after use.
Any modification of the appliance, misuse, or failure to follow the instructions may be
dangerous and will invalidate your warranty. This does not affect your statutory rights.
Retain these instructions for future reference.
Leak test annually, and whenever the gas bottle is removed or replaced. Check that the
hose connections are tight and leak test each time you reconnect the gas bottle.
For Flare-up control please refer to the ‘OPERATION’ section of this manual.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. If odour continues, discontinue use and
contact your local dealer.
FOR YOUR SAFETY
1. Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2. A gas bottle not connected for use shall not be
stored in the vicinity of this or any other
appliance.
0359
RC4343A
RC4341A
2
Parts List
Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see ‘Hardware Reference Diagram’.
CODE PART QTY Ranger 3
Gas BBQ
Ranger 3S
Gas BBQ
HOOD
A1 Hood (Pre-Assembled to Body) 1
A2 Hood Handle 1
A3 Heat Indicator 1
A4 Warming Rack 1
BODY
B1 Cooking Grill 2
B2 Flame Tamer 3
B3 Barbecue Body 1
B4 Knob 3
B5 Control Panel 1
B6 Burner 3
B7 Drip Tray Handle 1
B8 Drip Tray 1
B9 Drip Tray Left Bracket 1
B10 Drip Tray Right Bracket 1
B11 Side burner valve, Hose and Regulator Assembly 1
TROLLEY
C1 Side Burner Shelf 1
C2 Side Burner Base 1
C3 Ignition Button 1
C4 Side Burner 1
C5 Side Burner Electrode 1
C6 Side Burner Grid 1
C7 Side Burner Knob 1
C8 Side Shelf 1
C9 Hook Rail 1
C10 Tool Hook 3
C11 Bottle Opener 1
C12 Left Front Leg 1
C13 Left Rear Leg 1
C14 Right Front Leg 1
C15 Right Rear Leg 1
C16 Front Screen 1
C17 Trolley Base 1
C18 Axle 1
C19 Wheel 2
C20 Hubcap 2
HARDWARE
D1 M5x15 Bolt 4
D2 Washer 4
D3 M5 Nut 4
D4 M6x95 Bolt 8
D5 Spacer 8
D6 1/4-20UNCx25 Bolt 16
D7 1/4-20UNCx12 Bolt 10
D8 M6x10 Bolt 2
D9 M6x15 Bolt 4
D10 M6 Nut 4
D11 M4 Step Bolt 2
D12 M4x10 Bolt 2
D13 Wing Nut 1
D14 Locknut 2
Pre-Assembled Component
Quantity varies according to model purchased
Appearance, size, and construction may differ according to model purchased
3
Parts Diagrams
Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see hardware pack page.
B1
A4
C13C12
B11
A1
C16
A3
A2
B2
B4
B7
B8
B9 B10 C8
C15
C17
C20
C1
C11
C9
C10
C14
C19
D14 C18
B3
B6
C6
C5
C7
C3
B5
C2
C4
D13
4
Hardware Reference Diagram
Specifications subject to change without prior notice.
D1,D2,D3
D4,D5
D6
D7
D7
D8
D9,D10
D11
D12
5
2
Assembly
IMPORTANT!
TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver,
adjustable spanner or metric spanner set.
The assembly of this barbecue at least requires 2 people.
Remove any internal components or packaging from the barbecue body.
Whilst every care is taken in the manufacture of this product, care must be taken during assembly in
case sharp edges are present.
Please read the Important Information section carefully before assembly and use of your
barbecue.
1
Attach the Legs (C12, C13, C14, C15) onto the Trolley Base (C17) use 1/4-20UNCx12 Bolts
(D7x8pcs) as shown.
Note: Ensure that the legs with the Velcro attached to them are at the front of the barbecue, with
the Velcro facing inwards.
D7
Unscrew the Locknuts (D14) from both ends of the Axle (C18). Slide the axle through the
corresponding holes in the left legs. Slide the Wheels (C19) over each end of the axle.
Secure the wheels into place with the locknuts. Place the Hubcaps (C20) on the outsides
of the wheels.
D14 C18
C20 C19
C14
C15
C13
C12
C17
6
4
3
Insert M6x95 Bolts (D4x8pcs) through the trolley legs, the Spacers (D5x8pcs), and keep the tip of
the bolts inside the spacers. While holding the barbecue body into position (2 people required),
screw the bolts into the barbecue body as shown.
CAUTION! Care must be taken to ensure the hood or lid does not fall open unexpectedly or
becomes damaged when it is set on the ground.
D5 D4
Attach the Drip Tray Left Bracket (B9) to barbecue body using M5x15 Bolts (D1x2pcs), Washers
(D2x2pcs) and M5 Nuts (D3x2pcs) as shown. Repeat above process for Drip Tray Right Bracket
(B10).
NOTE: Ensure that the big tabs of the brackets which stop the drip tray are located at the
front of the barbecue.
FRONT
REAR
B9D1 D2 D3
7
6
5
Remove the retaining bolts from Drip Tray Handle (B7), then attach it onto the Drip Tray (B8)
using the retaining bolts.
Insert the drip tray by sliding it underneath the barbecue body.
B7
B8
Attach the Bottle Opener (C11) to the right front leg using 1/4-20UNCx12 Bolts (D7x2pcs).
C11
D7
8
8
7
C9C10 C8
D8
Insert the Hook Rail (C9) through the Tool Hooks (C10) as shown, then fix the assembly onto the
Side Shelf (C8) using M6x10 Bolts (D8x2pcs). Make sure the hooks are facing outwards.
Attach the side shelf assembly to the right front / rear Legs using 1/4-20UCNx25 Bolts (D6x8pcs) as
shown.
D6
9
10
9
Attach the Side Burner Shelf (C1) to the left front / rear Legs using 1/4-20UNCx25 Bolts (D6x8pcs)
as shown.
C3
C2
Pre-ass embled Nut
D9
Unscrew the pre-assembled nut of the Ignition Button (C3). Insert the ignition button through the
Side Burner Base (C2) and secure with the pre-assembled nut.
Carefully lay the side burner base into the side burner shelf, then fixing it by using M6x15 Bolts
(D9x4pcs) and M6 Nuts (D10x4pcs) as shown.
D10
D6
C1
10
11
Attach the side burner valve onto the side burner base using M4x10 Bolts (D12x2pcs) as shown.
12
Press the Side Burner Knob (C7) onto side burner valve stem.
D12
C7
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Outback Gril
Outback
Outback Sapphire THG3216AW Manuel utilisateur
Outback
Outback Spectrum Flamer Manuel utilisateur
Outback
Outback TPA101-6 Guide de référence rapide
Outback
Outback THG2710 Manuel utilisateur
Outback
Outback Omega 200 Manuel utilisateur
Outback
Outback Omega 150 Manuel utilisateur
Outback
Outback Society/Granite Manuel utilisateur
Outback
Outback RC4340S Manuel utilisateur
Outback
Outback Roast Box 500 Manuel utilisateur
Outback
Outback Sapphire 2 Burner Manuel utilisateur
Outback
Outback TS201 Manuel utilisateur
Outback
Outback Trooper Plus Manuel utilisateur
Outback
Outback Omega 100 Manuel utilisateur
Outback
Outback Jupiter 4S Manuel utilisateur
Outback
Outback Meteor 4S Manuel utilisateur
Outback
Outback Excel 100T Manuel utilisateur
Outback
Outback MS4464 Manuel utilisateur
Outback
Outback Charcoal Kettle CK575 Manuel utilisateur
Outback
Outback OUT371036 Manuel utilisateur
Outback
Outback RC4343C Manuel utilisateur
