oticon FittingLINK 3.0 Manuel utilisateur
Instructions for use
Wireless
Programmer
FittingLINK 3.0
Introduction to this booklet
This booklet guides you on how to use and maintain your new
FittingLINK 3.0. Please read the booklet carefully including the
“Warnings” section. This will help you get the most out of your new
FittingLINK 3.0.
If you have additional questions about the use of your FittingLINK
3.0, please contact your supplier’s support function.
For your convenience this booklet contains a navigation bar to help
you navigate easily through the different sections.
About Startup Daily use Warnings More info
Intended use
FittingLINK 3.0 is intended as a programming interface to fitting
software, for wireless transfer of fitting data from the device
running the fitting software to the wireless hearing aids.
FittingLINK 3.0 is intended to be used by hearing care professionals.
Compatibility
FittingLINK 3.0 is compatible with Oticon hearing aids with 2.4 GHz
radio technology. It is backwards compatible and can be used with
FittingLINK WP-2. For backwards compatibility refer to FittingLINK
WP-2 “Instructions for Use” which can be
found on: www.oticon.global
INSTRUCTIONS FOR USE
Table of contents
About
Package contents 6
Product overview 7
Start up
Connect FittingLINK 3.0 to a PC 8
FittingLINK 3.0 and your fitting software 11
Daily use
How to use FittingLINK 3.0 12
Pairing FittingLINK 3.0 with 2.4 GHz wireless hearing aids 14
LED indicator 18
Taking care of your FittingLINK 3.0 19
Troubleshooting 20
Warnings
Warnings 24
More info
International warranty 26
Technical information 27
Instructions for use
Wireless
Programmer
FittingLINK 3.0
6About Startup Daily use Warnings More info
About
Package contents
You will find the following items in the package:
FittingLINK 3.0 Desk stand Instructions for Use
(this booklet)
7
Product overview
FittingLINK 3.0
Desk stand
LED indicator
Cable (2 m)
USB 2.0
8About Startup Daily use Warnings More info
Connect FittingLINK 3.0 to a PC
Before FittingLINK 3.0 can be used as your programming device
for wireless hearing aids, Genie 2 must be installed on your PC.
FittingLINK 3.0 must then be plugged into your PC in one of two
ways:
You can choose to plug FittingLINK 3.0 in the desk stand and
connect the USB cable from the desk stand to the PC [A]
Start up
A
9
B
We recommend that you keep FittingLINK 3.0 in the desk stand to
ensure optimal performance.
or you can choose to plug FittingLINK 3.0 directly into a USB port on
the PC [B].
10
When you have connected FittingLINK 3.0 and turn on your PC the
first time, a small pop-up window will appear on the screen indicat-
ing that the applicable driver is being installed. Let the installation
finish before you proceed.
The driver installation runs only the first time you turn on your PC
or in case you unplug FittingLINK 3.0 and afterwards plug it into a
different USB port than the one originally used.
About Startup Daily use Warnings More info
Autres manuels pour FittingLINK 3.0
7
Table des matières
Autres manuels oticon Carte mère
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
