Olympus SZ-ADD Manuel utilisateur

INSTRUCTIONS

SZ2-ILA

TRANSMITTED ILLUMINATION

ATTACHMENT

This instruction manual is for the Olympus SZ2-ILA Transmitted Illumination Attachment. To ensure

the safety, obtain optimum performance and to familiarize yourself fully with the use of this equip-

ment, we recommend that you study this manual thoroughly before operating the system.

Retain this instruction manual in an easily accessible place near the work desk for future reference.

A X 6 6 1 5

SZ-ADD

SZ-POL-2

SZH-CLJ

Optional Modules

SZ2-ILA

4 TROUBLESHOOTING GUIDE

5 SPECIFICATIONS

6 ASSEMBLY

7 OPTIONAL MODULES

8-9

10-11

CONTENTS

IMPORTANT — Be sure to read this section for safe use of the equipment. —

1 SYSTEM CHART

2 NOMENCLATURE

3 TRANSMITTED LIGHT OBSERVATION

1-2

Correct assembly and adjustments are critical for this unit to manifest its full performance. If you are going to

assemble this unit by yourself, please read Chapter 6, “ASSEMBLY” (p. 8 to 9). For the assemblies of the modules for

which instruction manuals are available, refer to their instruction manuals.

Using the Mirror Rotation/Sliding Knob ........................................................................................................................................................ 5

7-1 Darkfield Adapter SZ-ADD ...................................................................................................................................................... 10

7-2 Simplified Polarization System SZ-POL-2 ......................................................................................................... 11

7-3 Jewel Observation Clip SZH-CLJ.................................................................................................................................... 11

8 LAMP HOUSING INSPECTION SHEET

IMPORTANT

The transmitted illumination attachment enables transmitted light observation when it is placed under

the SZ2-ST standard stand for the SZ2 series microscopes.

SAFETY PRECAUTIONS

1. If water is split on the unit, promptly set the main switch to “ ” (OFF) and wipe with a dry cloth.

2. The lamp housing becomes very hot during operation. When installing it, reserve enough spaces (more than 10 cm)

around it, particularly above it.

3. If the power cord comes in contact with the lamp housing or surrounding equipment, the cord may melt and result in

shock hazard. To prevent this, distribute the power cord apart from the lamp housing.

4. Before replacing the lamp bulb of the light source, set the main switch to “ ” (OFF), disconnect the power cord from the

wall outlet and allow the lamp housing and old bulb to cool down.

Illumination System Lamp Bulb Specifications

LSGA

U-LH100L-3

SZ2-LGB

6V15WHAL (PHILIPS 13528), average life 500 hours

12V100WHAL-L (PHILIPS 7724), average life 2000 hours

12V22WHAL (PHILIPS JCR12V22WA/3), average life 100 hours

5. Always use the power cord provided by Olympus. If the proper power cord is not used, product safety performance

cannot be warranted.

6. Always ensure that the grounding terminals are properly connected. If the equipment is not grounded, Olympus can no

longer warrant the electrical safety performance of the equipment.

7. Never allow a metallic object enter the air vents of the unit as this could result in electrical shock or malfunction.

8. The illumination light may be pointed downward with certain mirror angles. As this makes the desktop surface hot, do not

place an object that is vulnerable to heat or easily flammable below the transmitted light illumination attachment.

Safety Symbols

Symbol Explanation

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Before use, carefully read the instruction manual. Improper use could result in personal injury to

the user and/or damage to the equipment.

The following symbols are found on the unit. Study the meaning of the symbols and always use the equipment in the

safest possible manner.

Indicates that the surface becomes hot, and should not be touched with bare hands.

SZ2-ILA

Warning engraving

positions

Lamp housing

(U-LH100L-3)

(High Temperature

warning )

Warnings

Warning engravings are placed at parts where special precaution is required when handling and using the unit. Always

heed the warnings.

1Getting Ready

1. The transmitted light illumination attachment is a precision instrument. Handle it with care and avoid subjecting it to

sudden or severe impact.

2. Do not use the transmitted light illumination attachment where it is subjected to direct sunlight, high temperature and

humidity, dust or vibrations. (For the operating conditions, refer to Chapter 5, “SPECIFICATIONS” on page 7.)

2Maintenance and Storage

1. To clean the lenses and other glass components, simply blow dirty away using a commercially available blower and wipe

gently using a piece of cleaning paper (or clean gauze).

If a lens is stained with fingerprints or oil smudges, wipe it gauze slightly moistened with commercially available absolute

alcohol.

Since the absolute alcohol is highly flammable, it must be handled carefully.

Be sure to keep it away from open flames or potential sources of electrical sparks -- for example, electrical

equipment that is being switched on or off.

Also remember to always use it only in a well-ventilated room.

2. Do not attempt to use organic solvents to clean the parts other than the glass components. To clean them, use a lint-free,

soft cloth slightly moistened with a diluted neutral detergent.

3. Do not disassemble any part of the equipment as this could result in malfunction or reduced performance.

4. When the microscope is not in use, be sure to set the main switch to “ " (OFF). After checking that the lamp housing

has been cooled down, place the dust-prevention cover on the microscope for storage.

3Caution

If the transmitted illumination attachment is used in a manner not specified by this manual, the safety of the user may be

imperiled. In addition, the equipment may also be damaged. Always use the equipment as outlined in this instruction

manual.

The following symbols are used to set off text in this instruction manual.

: Indicates that failure to follow the instructions in the warning could result in bodily harm to the

user and/or damage to equipment (including objects in the vicinity of the equipment).

# : Indicates that failure to follow the instructions could result in damage to equipment.

} : Indicates commentary (for ease of operation and maintenance).

SYSTEM CHART

Stage Glass

SP-C

45 mm

frameless filter

Filter holder

Standard

Stand

SZ2-ST

Transmitted Illumination

Attachment

SZ2-ILA

Lamp Housing Adapter

SZ2-LHAD

100 W Halogen Lamp Housing

U-LH100L-3

Power supply

TH4

Lightguide

Illuminator

SZ2-LGB

Power supply

TL3

Epi-Illuminator

LSGA Flexible Light Guide

SZ2-LGSF

Collector Lens

SZ2-LGCL

Transmitted Light Guide

Adapter

SZ2-TLGAD

SZ2-ILA

NOMENCLATURE

Transmitted Illumination Attachment

SZ2-ILA

Fresnel lens

Mirror

Planar mirror/Light

scattering mirror

Illuminator mount port

Mirror rotation/sliding knob

Rotation: 360°

Sliding: 30 mm

Filter holder

Stage glass

SP-C

Power Supply

TH4 For details, refer to the instruction manual.

Main switch

“ I”: ON. “ ”: OFF

Intensity control knob

Power LED

Remote LED

Power Supply

TL3

Main switch

“ I”: ON. “ ”: OFF

Intensity control knob

Voltage position selectable

from 3, 4, 5 or 6

TRANSMITTED LIGHT OBSERVATION

}If you have not assembled the transmitted illumination attachment yet, please read Chapter 6, “ASSEMBLY” (p. 8 to 9).

Fig. 1

1Using the Mirror Rotation/Sliding Knob (Fig. 1)

1. Set the main switch of the power supply to “ I” (ON) and adjust the

brightness with the intensity control knob.

2. Adjust the illumination by rotating or sliding the mirror rotation/sliding

knob @.

}Usages of the planar and light scattering mirrors

· Planar mirror: Bright illumination.

· Light scattering mirror: Illumination with little light irregularities.

3. With a standard transmitted light illumination, slide the mirror rotation/

sliding knob @ to the deep part of the slide stroke and then rotate the

knob @ for an illumination with highest brightness and least irregularities.

Oblique Illumination

}When observing the specimen by shading on it, use oblique illumination

by rotating and sliding the knob @.

· While looking through the eyepieces, adjust the image contrast by sliding

and rotating the knob @ gradually toward you.

SZ2-ILA

TROUBLESHOOTING GUIDE

Problem Cause Remedy Page

–

Under certain conditions, performance of the unit may be adversely affected by factors other than defects. If problems occur,

please review the following list and take remedial action as needed. If you cannot solve the problem after checking the entire list,

please contact Olympus.

1. Optical system

a) Illumination is too bright or too dark. The intensity is adjusted improperly. Adjust the light intensity optimally.

A wrong ND filter is in use. Adjust the light intensity optimally.

b) Illumination irregularities are notice-

able.

The lamp bulb is attached improperly. Mount it properly.

The angle and/or position of the mirror

are set improperly.

Rotate and/or slide the mirror.

The stage glass is dirty. Clean thoroughly.

c) Dirt or dust is noticeable in the field

of view.

The stage glass is dirty.

The mirror is dirty.

The eyepiece and/or objective are dirty.

2. Electrical system

Clean thoroughly. 2

a) The lamp bulb will not light up. The bulb is blown. Replace it.

b. The lamp bulb blows easily. The supply voltage is too high. Reduce the voltage using a slidac.

A bulb other than designated is in use. Replace it with a designated bulb.

c) The lamp turns on and off inter-

mittently.

The bulb is half blown. Replace it. 9

Connectors are connected imperfectly. Connect connectors firmly. –

SPECIFICATIONS

Item Specifications

Illumination system*LSGA (Illumination System)

6 V, 15 W halogen bulb (6V15WHAL)

U-LH100L-3 (Illumination System) (SZ2-LHAD required)

12 V, 100 W halogen bulb (12V100WHAL-L)

Power source TL3 (Power Supply)

Voltage switching steps: 3, 4, 5 and 6 V

TH4 (Power Supply)

Step-less voltage switching

Effective field Diameter 33 mm

Filter 45 mm frameless filter usable (Filter with thickness up to 5 mm can be accommodated in the filter

holder.)

Lighting types Rotation/sliding of the planar and light scattering filters.

Oblique illumination possible.

Combined stand SZ2-ST (Standard Stand)

Combined stage height: 92.5 mm

Weight Approx. 1.1 kg (SZ2-ILA only)

Power consumption Max. 30 VA Max. 180 VA

Other · Various stages applicable.

· Darkfield Adapter (SZ-ADD) mountable.

· Simplified Polarization System (SZ-POL-2) mountable.

Operating environment · Indoor use

· Altitude: Max. 2000 m

· Ambient temperature: 5° to 40°C (41°F to 104°F)

· Maximum relative humidity: 80% for temperatures up to 31°C (88°F), decreasing linearly through

70% at 34°C (93°F), 60% at 37°C (99°F), to 50% relative humidity at 40°C (104°F)

· Supply voltage fluctuations: ±10%

· Pollution degree: 2 (in accordance with IEC60664)

· Installation (overvoltage) category: II (in accordance with IEC60664)

*For the light guide illumination, refer to the separate instruction manual.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Olympus Microscope

Olympus

Olympus BH2 Series Instructions d'installation

Olympus

Olympus FV3000 Guide de l'utilisateur

Olympus

Olympus K Mode d'emploi

Olympus

Olympus CHA-P Manuel utilisateur

Olympus

Olympus U-CBE Manuel utilisateur

Olympus

Olympus BX51 Manuel utilisateur

Olympus

Olympus IX81 Manuel utilisateur

Olympus

Olympus DP22 Manuel utilisateur

Olympus

Olympus CHBS Manuel utilisateur

Olympus

Olympus CK2 Manuel utilisateur

Olympus

Olympus SZ3060 Manuel utilisateur

Olympus

Olympus bx40 Manuel utilisateur

Olympus

Olympus BX51WI Manuel utilisateur

Olympus

Olympus DP73 Manuel utilisateur

Olympus

Olympus BX53 Manuel utilisateur

Olympus

Olympus Fluoview-1000 Manuel utilisateur

Olympus

Olympus BXFM Manuel utilisateur

Olympus

Olympus CX41 Manuel utilisateur

Olympus

Olympus CX40 Manuel utilisateur

Olympus

Olympus BH2 Series Mode d’emploi

Olympus

Olympus DP21 Manuel utilisateur

Olympus

Olympus MX63 Manuel utilisateur

Olympus

Olympus BH2 Series Manuel utilisateur

Olympus

Olympus CX23 Manuel utilisateur

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Leica

Leica FL560 Manuel utilisateur