Olympus SZX9 Manuel utilisateur

INSTRUCTIONS

SZX

RESEARCH STEREOMICROSCOPE

SYSTEM

This instruction manual is for the Olympus SZX Research Stereomicroscope System. To ensure the

safety, obtain optimum performance and to familiarize yourself fully with the use of this microscope,

we recommend that you study this manual thoroughly before operating the microscope. Retain this

instruction manual in an easily accessible place near the work desk for future reference.

A X 7 1 6 8

SZX9/12

SZX-EPA

SZX-AS

SZX-R

SZX-2RE

SZX-STAD1

SZX-STAD2

SZH-STAD1

IMPORTANT

SAFETY PRECAUTIONS

1. To prevent the microscope body from turning over, its pivot angle must

be limited to 30° as shown in Fig. 1.

2. Sufficient care is required during observation with a magnification objec-

tive, because the objective´s long working distance can displace the

microscope body to a higher position. Care is also required when using

an auxiliary pillar (SZH-P400/P600), which also makes the microscope

body unstable.

3. To adjust the microscope body height, be sure to hold the focusing as-

sembly with one hand while loosening the focusing assembly clamping

knob @. (Fig. 1)

(Use the drop prevention collar (SZX-R) to prevent a hazard from occurring.)

Fig. 1

1Getting Ready

1. A microscope is a precision instrument. Handle it with care and avoid

subjecting it to sudden or severe impact.

2. Do not use the microscope where it is subjected to direct sunlight, high

temperature and humidity, or vibration. (For operating environment, see

Section 6, “Specifications” on page 16.)

3. Observe the following cautions when operating the coarse or fine focus

adjustment knobs or the zooming knob.

Fig. 2

Operation Manipulated Controls Caution

Focusing Coarse/fine focus ad-

justment knobs @

(Fig. 2)

1. If the knob hits the upper or lower

limiting mechanism violently or

it is rotated after it hits a limiting

mechanism, the internal mecha-

nism may be damaged.

2. If the knobs on the left and right

are rotated in opposite directions,

the internal mechanism will be

damaged. (The tension of the

coarse focus adjustment knob

should be adjusted using the

tension adjustment ring ³ on the

knob.)

Zooming Zooming knob ²

(Fig. 2)

1. If the knob hits the upper or lower

limiting mechanism violently or

it is rotated after it has hit a limit-

ing mechanism, the internal

mechanism may be damaged.

2. If the knobs on the left and right

are rotated in opposite directions,

the internal mechanism will be

damaged.

30°

²³

4. Only one intermediate attachment can be used. Using two attachments

may obscure a part of the image. However, the vertical illuminator (SZX-

ILLC) is not considered to be an attachment.

}When more than one intermediate attachment is to be combined, they

should be stacked according to the following order, from the bottom to

the top: SZX-ILLC, SZX-AS, SZX-RFA (SZX-RFL), SZX-SDO, SZX-APT, SZX-

BS, SZX-DA, SZX-FAD, then SZX-EPA.

5. The desk surface inclination with respect to the horizontal surface should

be less than 5°.

2Maintenance and Storage

1. Clean all glass components by wiping gently with gauze. To remove fingerprints or oil smudges, wipe with gauze slightly

moistened with a mixture of ether (70%) and alcohol (30%).

Since solvents such as ether and alcohol are highly flammable, they must be handled carefully. Be sure to keep

these chemicals away from open flames or potential sources of electrical sparks -- for example, electrical equip-

ment that is being switched on or off. Also remember to always use these chemicals only in a well-ventilated

room.

2. The equipment uses plastic resins extensively in its external finish. Do not attempt to use organic solvents to clean the

non-optical components of the microscope. To clean these components, use a lint-free, soft cloth lightly moistened with a

diluted neutral detergent.

3. Never disassemble any part of the microscope as this could result in malfunctions or reduced performance.

4. When not using the microscope, keep it covered with the dust cover provided.

3Caution

If the microscope is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition,

the microscope may also be damaged. Always use the microscope as outlined in this instruction manual.

The following symbols are used to set off text in this instruction manual.

: Indicates that failure to follow the instructions in the warning could result in bodily harm to the

user and/or damage to equipment (including objects in the vicinity of the equipment).

# : Indicates that failure to follow the instructions could result in damage to equipment.

} : Indicates commentary (for ease of operation and maintenance).

CONTENTS

1NOMENCLATURE

2ASSEMBLY

2-1 Assembly Diagram ........................................................................................................................................................................ 2

2-2 Detailed Assembly Procedure...................................................................................................................................... 3

3CONTROLS

4SUMMARY OF OBSERVATION PROCEDURE

4-1 Preparation ............................................................................................................................................................................................... 7

4-2 Observation Procedure .......................................................................................................................................................... 7

5USING THE CONTROLS

5-1 Base .................................................................................................................................................................................................................... 8

5-2 Microscope Body and Focusing Assembly.............................................................................................. 8

5-3 Observation Tube ......................................................................................................................................................................... 11

5-4 TV Observation and Photomicrography...................................................................................................... 14

6SPECIFICATIONS

7OPTICAL CHARACTERISTICS

8TROUBLESHOOTING GUIDE

9OPERATION OF OTHER ATTACHMENTS

9-1 Eyepoint Adjuster SZX-EPA............................................................................................................................................ 19

9-2 AS Unit SZX-AS (for use with the SZX-ZB9) ......................................................................................... 20

9-3 Drop Prevention Collar SZX-R and Auxiliary Pillar SZH-P400/SZH-P600 .......... 21

9-4 Revolving Nosepiece SZX-2RE .............................................................................................................................. 22

9-5 BX Stage Adapter Type 1 SZX-STAD1 .......................................................................................................... 24

9-6 BX Stage Adapter Type 2 SZX-STAD2 .......................................................................................................... 26

9-7 Stage Adapter Type 1 SZH-STAD1 ..................................................................................................................... 27

SZX

NOMENCLATURE

Eyepiece

· WHS10X-H

· CROSS WHS10X

· WHS15X-H

· CROSS WHS15X

· WHS20X-H

· CROSS WHS20X

· WHS30X-H

Microscope

body

· 12X zoom microscope

body: SZX-ZB12

· 9X zoom microscope

body: SZX-ZB9

Objective

þFor SZX-ZB12ý þFor SZX-ZB9ý

· DFPLFL0.3X* · DFPL0.5X-4*

· DFPLFL0.45X* · DFPL0.75X-4

· DFPLFL0.5XPF · DFPLAPO1X-4

· DFPLAPO1XPF · SZX-ACH1X

· DFPLAPO1.2XPF2 · SZX-ACH1.25X

· DFPLFL1.6XPF · DFPL1.5X-4

· SZX-AL20X · DFPL2X-4

Observation tube

· Binocular observation

tube: SZX-BI30/BI45

· Trinocular observation

tube: SZX-TR30

· Tilting binocular tube:

SZX-TBI

Focusing assembly

· Coarse/fine focus adjustment

knobs: SZX-FOF

· Focus adjustment knob:

SZX-FO

Intermediate

attachment**

· Eyepoint adjuster: SZX-EPA

· AS unit: SZX-AS

etc.

Base**

· Standard base: SZX-ST

· Large base: SZX-STL

· Transmitted light base: SZX-ILLK

SZX-ILLB2

SZX-ILLD2

* The standard base (SZX-ST) requires use of an optional auxiliary pillar (SZH-P400) and optional drop prevention collar

(SZX-R). The large base (SZX-STL) comes with the auxiliary pillar (SZH-P400) mounted as standard. This enables the large

base to be used as is. However, be sure to use the drop prevention collar (SZX-R) in combination.

** For other attachments, refer to the product catalogue.

SZX

ASSEMBLY

2-1 Assembly Diagram

The diagram below shows how to assemble the various modules. The numbers indicate the order of assembly.

#When assembling the microscope, make sure that all parts are free of dust and dirt, and avoid scratching any parts

or touching glass surfaces.

Allen screwdriver

(provided with the zoom

microscope body)

Allen wrench*

(provided with the stan-

dard base)

Required tools

* Do not use the Allen wrench for a purpose

other than installing the auxiliary pillar. If the

Allen wrench is used for a part other than that

described above, the force with which it is

applied may break the part.

Eyepiece

Observation tube

Intermediate

attachment

Zoom microscope body

Objective

Auxiliary objective

SZX-AL20X

Focusing assembly

Stage plate Specimen

holder

Pillar

Standard base

2-2 Detailed Assembly Procedure

Fig. 3

Fig. 4

Fig. 5

1 Installing the Pillar (Fig. 3)

1. Using the Allen wrench provided with the base, loosen the 2 clamping

screws @ on the pillar support sleeve completely.

2. Hold the pillar ² with the white rubber cap at the top, and insert it into the

pillar support sleeve until it reaches the bottom.

3. Using the provided Allen wrench, tighten the 2 clamping screws ²

securely.

2Mounting the Focusing Assembly (Figs. 4 & 5)

1. First loosen the focusing assembly clamping knob @ completely, and

while holding the focusing assembly with both hands, insert the pillar ³

into the mounting hole ² from below. (Fig. 4)

#Insert slowly. Do not apply excessive force.

2. Lower the focusing assembly until it stops, then tighten the focusing

assembly clamping knob @. (Fig. 4)

To prevent the microscope from turning over, the focusing assembly

must be installed on the same side as the stage plate in the stand,

as shown in the illustration marked “ ” in Fig. 5, and its pivot angle

must be limited to 30°. If the focusing assembly is placed on the

wrong side, the microscope will turn over.

#If the clamping knob @ is tightened while the pillar ³ is not com-

pletely inserted into the mounting hole ², the plate spring support-

ing the pillar will deform and the pillar will not be able to penetrate

into the hole. (Fig. 4)

30°or less

SZX

Fig. 6

Fig. 7

Fig. 8

3Mounting the Microscope Body (Fig. 6)

1. Remove the cap @ on the focusing assembly by inserting a thin object

into the notch.

2. Using the provided Allen screwdriver, loosen the dovetail mount clamp-

ing screw inside the cap on the focusing assembly by rotating it by 2 or

3 turns (counterclockwise).

3. Gently insert the dovetail mount ³ on the rear of the microscope body

into the dovetail mounting port ² on the focusing assembly.

# Do not insert the mount at an angle or with excessive force, for this

may cause malfunctions.

4. When the microscope body has been inserted until it stops, tighten the

clamping screw using the Allen screwdriver.

5. Place the cap @ in the original position.

4Mounting the Objective (Fig. 7)

Mount the objective ² on the objective mount thread @ by rotating the

objective in the direction of the arrow.

Mounting the Auxiliary Objective SZX-AL20X (SZX-ZB12 only)

When using the auxiliary objective (SZX-AL20X), mount it onto the tip

of the DFPLAPO1XPF objective and tighten the clamping screw while

pushing it against the tip. (See page 10.)

Remember that the SZX-AL20X cannot be used with other objectives.

5Mounting the Observation Tube (Fig. 8)

1. Using the Allen screwdriver, loosen the observation tube clamping screw

@ completely.

2. Aligning the positioning pin ³ of the microscope body to the positioning

groove ² on the observation tube, insert the dovetail mount | at the

bottom of the observation tube into the mounting port ƒ on the micro-

scope body.

3. Using the Allen screwdriver, tighten the observation tube clamping

screw @.

# The observation tube can be mounted 180° from the above posi-

tion, but this positioning makes observation difficult and is not rec-

ommended. When the auxiliary pillar is used, this positioning is im-

possible because the eyepiece gets in the way.

6Mounting the Eyepiece (Fig. 9)

1. Remove the eyepiece dust caps @ and loosen the eyepiece clamping

screws ² completely.

2. Gently insert the cross-lined eyepiece (CROSS WHS10X) ³ (if this is not

provided, use the WHS10X-H) into the right eyepiece sleeve until it stops.

3. Gently insert the eyepiece (WHS10X-H) into the left eyepiece sleeve until

it comes up against the stop.

4. Tighten both eyepiece clamping screws ².

7Mounting (Removing) the Stage Plate (Fig. 10)

Place the stage plate (white, black on back side) into the mounting hole

on the base.

To remove, press the stage plate at the edge nearest to the pillar with

your fingertip. The opposite end will rise from the base so the stage plate

can be picked up easily.

8Mounting the Specimen Holder (Fig. 11)

Insert the specimen holder @ into the 2 holes ² on the top surface of the

base.

9Positioning the Microscope Body on the Stand(Fig. 12)

Loosen the focusing assembly clamping knob @. Slightly pivoting the

microscope body to the left and right, align the center of the objective

with the center of the stage plate ², then clamp the microscope body

with the focusing assembly clamping knob.

Fig. 9

Fig. 10

Fig. 11

Fig. 12

SZX

CONTROLS

Zooming knob

SZX-ZB12: 0.7X to 9X

SZX-ZB9: 0.63X to 5.7X

Diopter adjustment ring

±5m-1 (per meter)

Eyepiece clamping knob

Aperture iris diaphragm ring

(SZX-ZB12 only)

Observation magnification

indicator

Shows the total magnification

when the objective is 1X and eye-

piece is 10X.

Click stop ON-OFF screw

Engages or disengages the click stop func-

tion for each magnification indicated on the

zooming knob.

Light guide hole

SZX-CSP/LG-DFI mounting holes

Focusing assembly

clamping knob

Pillar clamping screws

Spare screw holes

(4 mm threaded holes x 4)

Used to mount a manipulator, etc.

Light path selector knob

(SZX-TR30 only)

Coarse focus adjustment knob

Stroke: 80 mm

Stroke per turn (SZX-FOF): 36.8 mm

Stroke per turn (SZX-FO): 21.2 mm

Fine focus adjustment knob

(SZX-FOF only)

Stroke: 80 mm

Stroke per turn: 1.5 mm

Coarse focus adjustment knob

tension adjustment ring

Specimen holder

Hand rest

Magnification indicator ring

Provided with the objective

(except 1X objective).

} Can also be attached onto

the right zooming knob.

Stage adapter screw hole

(4 mm threaded x 2)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Olympus Microscope

Olympus

Olympus BX43 Manuel utilisateur

Olympus

Olympus CKX41 Manuel utilisateur

Olympus

Olympus BXC-CBB Manuel utilisateur

Olympus

Olympus CX21LED Manuel utilisateur

Olympus

Olympus BH-2 BHT Manuel utilisateur

Olympus

Olympus IMT-2 Manuel utilisateur

Olympus

Olympus BH2 Series Manuel utilisateur

Olympus

Olympus U-D7RES Manuel utilisateur

Olympus

Olympus GX41 Manuel utilisateur

Olympus

Olympus CHBS Manuel utilisateur

Olympus

Olympus IX70 Manuel utilisateur

Olympus

Olympus SZ2-ILA Manuel utilisateur

Olympus

Olympus ORBEYE Manuel

Olympus

Olympus VMF Mode d'emploi

Olympus

Olympus U-FWT Manuel utilisateur

Olympus

Olympus Fluoview FV1000 Guide d'installation

Olympus

Olympus BH2-6RE Manuel utilisateur

Olympus

Olympus U-D7RES Manuel utilisateur

Olympus

Olympus Pom Manuel utilisateur

Olympus

Olympus BH2 Series Mode d’emploi

Olympus

Olympus BH2 Series Instructions d'installation

Olympus

Olympus FV5-LD405 Manuel utilisateur

Olympus

Olympus BHTU-112 Manuel utilisateur

Olympus

Olympus MX63 Manuel utilisateur

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Leica

Leica FL560 Manuel utilisateur