Olympus BXFM Series Manuel utilisateur

INSTRUCTIONS

BXFM

FOCUSING UNIT

A X 7 6 1 3

This instruction manual is for the Olympus Focusing Unit model BXFM and associated modules.

To ensure safety, optimum performance and familiarize yourself fully with the use of the assembled

microscope, we recommend that you study this manual thoroughly before operating the unit. Re-

tain this instruction manual in an easily accessible place near the work desk for future reference.

This publication is printed on 100% recycled paper

BXFM

CONTENTS

5,6

7, 8

9-13

IMPORTANT — Be sure to read this section for safe use of the equipment. —

1 SYSTEM DIAGRAM

2 NOMENCLATURE

4 USING THE CONTROLS

REFLECTED LIGHT BRIGHTFIELD OBSERVATION PROCEDURE

4-1 Base and Power Supply............................................................................................................................................................... 9

4-2 Focusing Unit ........................................................................................................................................................................................... 10

1Voltage Indication 2Placing the Specimen

4-3 Observation Tube ......................................................................................................................................................................... 11,12

4-4 Reflected Light Illuminator (U-KMAS) .................................................................................................................... 13

14-16

1Adjusting the Interpupillar Distance 2Adjusting the Diopter

3Using the Eye Shade 4Using Eyepiece Micrometer Disks

5Selecting the Light Path of Trinocular Tube 6

Adjusting the Tilt (with the U-TBI3/SWETTR2)

1Using the Filters

Adjusting the Coarse Adjustment Knob Tension

Using the Rubber Fine Adjustment Knob Cap

1-3

Correct assembly and adjustments are critical for the microscope to exhibit its full performance. If you are going to

assemble the microscope yourself, please read chapter 10, “ASSEMBLY” (pages 24 to 27) carefully.

6 TROUBLESHOOTING GUIDE

7 SPECIFICATIONS

8 MAIN DIMENSION DIAGRAM

9 OPTICAL CHARACTERISTICS «UIS2 (UIS) Series»

PROPER SELECTION OF THE POWER SUPPLY CORD ....................................................................... 28,29

ASSEMBLY

—

See this section for the replacement of the light bulb. —

5-1 Reflected Light Brightfield Observation............................................................................................................. 14

5-2 Reflected Light Nomarski DIC Observation .......................................................................................14-16

5-3 Reflected Light Simplified Polarized Light Observation ............................................................ 16

5 OBSERVATION METHODS (Using U-KMAS)

17,18

20,21

22,23

24-27

IMPORTANT

The BXFM focusing unit can be used as the basis for installing modules such as reflected light illumina-

tion equipment, objectives, eyepieces and observation tube for construction of a microscope system.

The BXFM can be installed on the exclusive stand or on your microscope.

SAFETY PRECAUTIONS

1. Install the microscope on a sturdy, level table or bench so as not to

block the air vents on the underside of the base.

2. When combing the stand (U-ST), install the BXFM so that it forms an

angle of ±30° with respect to the pillar as shown in Fig. 1.

The compact brightfield illuminator (U-KMAS) should be installed so that,

when it is seen from the front, the lamp housing is located on its right

side.

3. When carrying the BXFM, hold the stand by the bottom with one hand

as shown in Fig. 2, and hold the focusing block with the other hand.

# Do not hold the BXFM by the coarse/fine adjustment knobs or lamp

housing. Otherwise, the microscope may be damaged.

4. The surface of the lamp housing @ on the rear of the microscope be-

comes very hot. When installing the microscope system, leave spaces

of more than 10 cm around the lamp housing, particularly on the top

and bottom.

Do not install the lamp housing up side down or with the side facing up.

Also do not use the microscope in a tilted attitude.

5. The TH4 power supply is air-cooled so it becomes during operation.

When installing it, leave spaces of more than around it. Also make sure

to distribute cables away from the power supply.

6. Be sure to set the main switch to “ ” (OFF) and unplug the power cord

before replacing the light source bulb. (P. 26)

7. Always use the power cord provided by Olympus. If no power cord is

provided, please select the proper power cord by referring to the chapter

“PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of

this instruction manual. If the proper power cord is not used, product

safety and performance cannot be guaranteed.

8. Always ensure that the grounding terminal of the microscope and that

of the wall outlet are properly connected. If the equipment is not grounded,

Olympus can no longer warrant the electrical safety and performance of

the equipment.

Fig. 1

Fig. 2

Front

Back

BXFM

Illuminator

Mounting Holder BXFM-ILHS BXFM-ILH

Standard

Combination

Weight (Module

Names)

7.5 kg

BX-RLA2, U-TR30-2,

U-LH100-3, revolving

nosepiece, objec-

tives, eyepiece

Additional Load

Limit 2.8 kg

4.0 kg

When the BXFM-

ILHSPU counter

spring is used

5.2 kg

U-KMAS, U-TR30-2,

U-LH100-3, revolving

nosepiece, objec-

tives, eyepiece

· With the combination using the BXFM-ILH illuminator mounting holder,

do not use the U-ST stand because this makes the system unstable.

· The system can be stabilized by using the SZ-STL large stand, but the

image may fluctuate or blur irregularly when a 50X or higher-power ob-

jective is used.

· It is recommended to fabricate an exclusive clamping tool which uses

the support mounting hole (P. 20) or module mounting screw hole of the

BXFM-F focusing unit.

Symbol Explanation

The following symbols are found on the microscope. Study the meaning of the symbols and always use the equip-

ment in the safest possible manner.

Indicates that the surface becomes hot, and should not be touched with bare hands.

Before use, carefully read the instruction manual. Improper use could result in personal injury to

the user and/or damage to the equipment.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Warning engraving/stickers are placed at parts where special precaution is required when handling and using the

microscope. Always heed the warnings.

Warning engraving

position

Lamp housing

(Warning against high temperature)

Safety Symbols

Warnings

9. When using a photographic unit or TV camera, be sure to observe the

total weight limit of the modules added to the standard combination as

shown below.

1Getting Ready

1. A microscope is a precision instrument. Handle it with care and avoid subjecting it to sudden or severe impact.

2. Do not use the microscope system where it is subjected to direct sunlight, high temperature and humidity, dust or

vibrations. (For the operating conditions, refer to chapter 7, “SPECIFICATIONS”.)

3. One intermediate attachment can be used by installing U-CA magnification changer or U-EPA2 eyepoint adjuster above

the reflected light illuminator.

2Maintenance and Storage

1. To clean the lenses and other glass components, simply blow dirty away using a commercially available blower and wipe

gently using a piece of cleaning paper (or clean gauze).

If a lens is stained with fingerprints or oil smudges, wipe it gauze slightly moistened with commercially available absolute

alcohol.

Since the absolute alcohol is highly flammable, it must be handled carefully.

Be sure to keep it away from open flames or potential sources of electrical sparks –– for example, electrical

equipment that is being switched on or off.

Also remember to always use it only in a well-ventilated room.

2. Do not attempt to use organic solvents to clean the microscope components other than the glass components. To clean

them, use a lint-free, soft cloth slightly moistened with a diluted neutral detergent.

3. Never attempt to disassemble any part of the microscope system.

4. When not using the microscope, set the main switch to “ ” (OFF). After making sure the lamp housing has cooled down

sufficiently, cover it with a dust cover.

5. When disposing of this product, check the regulations and rules of your local government and be sure to observe them.

3Caution

If the microscope is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition,

the equipment may also be damaged. Always use the equipment as outlined in this instruction manual.

The warning, caution and other notes in this manual use the following symbols.

: Indicates that failure to follow the instructions in the warning could result in bodily harm to the

user and/or damage to equipment (including objects in the vicinity of the equipment).

# : Indicates that failure to follow the instructions could result in damage to equipment.

} : Indicates commentary (for ease of operation and maintenance).

BXFM

SYSTEM DIAGRAM

}This instruction manual gives description the modules which are connected in thick and broken lines in the following

diagram. For other modules, please refer to their instruction manuals.

*Reflected Light Lamp Housing

Halogen bulb:

U-LH100-3

(Power Supply TH4)

Mercury burner:

U-LH100HG

U-LH100HGAPO

Xenon burner:

U-LH75XEAPO

** For the modules without the model names, consult your dealer or the latest catalogues.

Eyepiece**

Module support

pillar or module

mounting block

Reflected

Light Lamp

Housing*

Reflected Light

Illuminator

BX-URA2

BX-RLA2 Revolving

Nosepiece**

Objective**

Illuminator

Mounting Holder

BXFM-ILH

Revolving

Nosepiece**

Objective**

Illuminator

Mounting

Holder S

BXFM-ILHS

Large Stand

SZ-STL

Observation Tube**

Intermediate tube**

Compact Reflected

Light Brightfield Illuminator

U-KMAS

Reflected Light

Lamp Housing*

Focusing Unit

BXFM-F

Counter Spring

BXFM-ILHSPU

Stand

U-ST

NOMENCLATURE

Focusing Unit BXFM-F

Compact Reflected Light Brightfield Illuminator U-KMAS

Observation tube mount

Illuminator Mounting Holder S BXFM-ILHS

}The U-KMAS reflected light illuminator can be mounted.

U-KMAS mount

*Used when the BX-RLA2 or BX-URA2 illuminator is

combined with the focusing unit. (P. 27)

Fine adjustment knob

Pillar mounting hole

Revolving nosepiece mount dovetail

Analyzer insertion slot

Polarizer insertion slot

Lamp housing mount

Filter insertion slot

Coarse adjustment knob

tension adjustment ring

Coarse adjustment knob

Fine adjustment knob

Rubber fine adjustment knob cap

BXFM-ILHSPU counter spring mounting screw hole

Auxiliary centering screws*

( 32 mm)

BXFM

Illuminator Holder BXFM-ILH, Counter Spring BXFM-ILHSPU

}The BX-URA2 or BX-RLA2 reflected light illuminator can be installed. The BXFM-ILHSPU is used to reduce the load on

focusing due to the weight of the reflected light illuminator and its accessories.

Illuminator mount screw holes

Stand U-ST Pillar Power Supply TH4

POWER LED

Hand Switch TH4-HS

Brightness control knob

Mounting holes x 4

Specimen holder

Stage plate

REMOTE LED

Main switch Brightness control knob

Lamp ON-OFF switch

“ I”: ON, “ ”: OFF

REFLECTED LIGHT BRIGHTFIELD OBSERVATION

PROCEDURE

}The following flow chart pertains only to the reflected light brightfield observation which is the most basic operation. The

procedures for the polarized light and Nomarski DIC operations will be described in their respective sections.

(Controls Used) (Page)

Set the main switch to “ I” (ON).

Disengage the analyzer, polarizer,

filter, etc. from the light path.

Select the light path (only when a trinocular

tube is used).

Place the specimen on the stage plate.

Engage the 10X objective in the light path.

Bring the specimen in focus.

Adjust the brightness.

Adjust the interpupillary distance.

Adjust the diopter.

Engage the desired objective in the light path

and bring the specimen in focus.

Insert the required filters.

Adjust the brightness.

Start observation.

@Main switch (P. 9)

²Lamp ON-OFF switch

³Brightness control knob

Light path selector knob (P. 12)

|Specimen holder (P. 9)

ƒRevolving nosepiece

…Coarse/fine adjustment knobs (P. 10)

³Brightness control knob (P. 9)

†Binocular tube (P. 11)

‡Diopter adjustment ring (P. 11)

ƒRevolving nosepiece

…Coarse/fine adjustment knobs (P. 10)

ŠFilter insertion slot (P. 13)

³Brightness control knob (P. 9)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Olympus Microscope

Olympus

Olympus SZX16 Manuel utilisateur

Olympus

Olympus FLUOVIEW FV300 Guide d'installation

Olympus

Olympus DSX1000 Manuel utilisateur

Olympus

Olympus DSX1000 Manuel utilisateur

Olympus

Olympus BHTU Manuel utilisateur

Olympus

Olympus CH2 Series Mode d'emploi

Olympus

Olympus U-UVF248A Manuel utilisateur

Olympus

Olympus IMT-2 Manuel utilisateur

Olympus

Olympus BX53M-P Manuel utilisateur

Olympus

Olympus BX2 SERIES Manuel utilisateur

Olympus

Olympus SLIDEVIEW VS200 Manuel utilisateur

Olympus

Olympus VMF Mode d'emploi

Olympus

Olympus GX41 Manuel utilisateur

Olympus

Olympus ST. HS Manuel utilisateur

Olympus

Olympus BH2 Series Mode d'emploi

Olympus

Olympus BXC-CBB Manuel utilisateur

Olympus

Olympus Pom Manuel utilisateur

Olympus

Olympus BX51-P Manuel du propriétaire

Olympus

Olympus VANOX Manuel utilisateur

Olympus

Olympus BH2-6RE Manuel utilisateur

Olympus

Olympus U-MDOB3 Manuel utilisateur

Olympus

Olympus AL120-12 Series Manuel utilisateur

Olympus

Olympus BX-FLA Manuel utilisateur

Olympus

Olympus IX2-DSU Manuel utilisateur

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Leica

Leica FL560 Manuel utilisateur