OHAUS CD-1 Manuel utilisateur

INSTRUCTION MANUAL

Model CD-1 Indicator

MANUAL DE INSTRUCCIONES

Indicador modelo CD-1

MANUEL DE LUTILISATEUR

Indicateur modèle CD-1

Ohaus Corporation, 19A Chapin Road, P.O. Box 2033, Pine Brook, NJ, 07058, U A

Declaration of Conformit We, Ohaus Corporation, declare under our sole responsibility that the indicator model listed below marked

with "CE" are in conformity with the directives and standards mentioned.

Indicator model CD-1

Marked with: EC Directive (Including applicable amendments) Standard

73/23/EC EN60950:1992

Electrical equipment for use within specified voltage limits afety of Information Technology Equipment

89/336/EC EN61326:1997 + A1:1998

Electromagnetic compatibility Electrical Equipment for Measurement, Control and Laboratory Use -

EMC requirements

ISO 9001 Registration for Ohaus Corporation.

Ohaus Corporation, U A, was examined and evaluated in 1994 by the Bureau Veritas Quality

International (BVQI) and was awarded I O 9001 registration. This certifies that Ohaus Corporation, U A, has a quality system that conforms with the

international standards for quality management and quality assurance (I O 9000 series). Repeat audits are carried out by BVQI at intervals to check

that the quality system is operated in the proper manner.

FCC NOTE: THI EQUIPMENT HA BEEN TE TED AND FOUND TO COMPLY WITH THE LIMIT FOR A CLA A DIGITAL DEVICE, PUR UANT

TO PART 15 OF THE FCC RULE .

THE E LIMIT ARE DE IGNED TO PROVIDE REA ONABLE PROTECTION AGAIN T HARMFUL INTERFERENCE WHEN THE EQUIPMENT I

OPERATED IN A COMMERCIAL ENVIRONMENT. THI EQUIPMENT GENERATE , U E , AND CAN RADIATE RADIO FREQUENCY ENERGY

AND, IF NOT IN TALLED AND U ED IN ACCORDANCE WITH THE IN TRUCTION MANUAL, MAY CAU E HARMFUL INTERFERENCE TO

RADIO COMMUNICATION . OPERATION OF THI EQUIPMENT IN A RE IDENTIAL AREA I LIKELY TO CAU E HARMFUL INTERFERENCE IN

WHICH CA E THE U ER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HI OWN EXPEN E.

Ted Xia

President

Ohaus Corporation, Pine Brook, NJ U An

THI DIGITAL APPARATU DOE NOT EXCEED THE CLA A LIMIT FOR RADIO NOI E EMI ION FROM DIGITAL APPARATU A ET OUT IN

THE INTERFERENCE-CAU ING EQUIPMENT TANDARD ENTITLED DIGITAL APPARATU , ICE -003 OF THE DEPARTMENT OF COMMUNICA-

TION CANADA.

CET APPAREIL NUMERIQUE RE PECTE LE LIMITE DE BRUIT RADIOELECTRIQUE APPLICABLE AUX APPAREIL NUMERIQUE DE CLA E

A PRE CRITE DAN LA NORME UR LE MATERIEL BROUILLEUR: APPAREIL NUMERIQUE , NMB-003 EDICTEE PAR LE MINI TRE DE

Unauthorized changes or modifications to this equipment are not permitted.

Last two digits of the year which the CE marking was affixed: 02

TABLE OF CONTENTS

1. GETTING TO KNOW YOUR CD-1 INDICATOR ................................................................................................................ 1

1.1 Introduction .............................................................................................................................................................. 1

1.1.1 Features ......................................................................................................................................................... 1

2. INSTALLATION .......................................................................................................................................................... 1

2.1 Unpacking and Checking............................................................................................................................................ 1

2.2 electing the Location ................................................................................................................................................ 2

2.3 Cautionary Notes ....................................................................................................................................................... 2

2.4 Connecting the CD-1 Indicator to a cale Base ............................................................................................................. 2

2.5 Connecting Power ..................................................................................................................................................... 2

2.5.1 AC Adapter....................................................................................................................................................... 2

2.5.2 Battery Installation ............................................................................................................................................ 2

3. SETUP...................................................................................................................................................................... 3

3.1 Overview of Controls and Display Functions ................................................................................................................. 3

3.2 Menu tructure .......................................................................................................................................................... 4

3.3 Available ettings ...................................................................................................................................................... 4

3.4 etup Procedure ........................................................................................................................................................ 5

3.5 Calibration Procedure ................................................................................................................................................. 6

4. OPERATION .............................................................................................................................................................. 7

4.1 Turning the CD-1 Indicator On/Off ................................................................................................................................ 7

4.2 Weighing .................................................................................................................................................................. 7

4.3 Zero Operation .......................................................................................................................................................... 7

4.4 Tare Operation .......................................................................................................................................................... 7

4.5 Clear Tare Operation .................................................................................................................................................. 8

5. CARE AND MAINTENANCE ......................................................................................................................................... 8

5.1 Troubleshooting ........................................................................................................................................................ 8

5.2 Error Codes List ......................................................................................................................................................... 8

5.3 ervice Information .................................................................................................................................................... 9

5.4 Accessories .............................................................................................................................................................. 9

6. TECHNICAL DATA...................................................................................................................................................... 9

CD-1 Indicator

1. GETTING TO KNOW YOUR CD-1 INDICATOR

1.1 Introduction

Thank you for deciding to purchase a CD-1 Indicator from Ohaus. The Ohaus CD-1 Indicator is a rugged, reliable,

electronic weight indicator designed for easy operation. The CD-1 Indicator can drive one analog load cell and provide

capacity selections up to 1,000kg.

The CD-1 Indicator operates from six Alkaline AA batteries and can also be powered externally using the supplied AC

adapter. A 0.9 inch / 2.3 centimeters high LCD provides easy visibility when working at distances from the indicator.

Two membrane switches are mounted on the front panel that enable simple set up procedures. A metal bracket with

hardware is included that permits mounting the indicator to a wall or table.

Behind your instrument stands OHAU , a leading manufacturer of precision Indicators, cales and Balances. An

Aftermarket Department with trained instrument technicians is dedicated to providing you with the fastest service pos-

sible in the event your instrument requires servicing. OHAU also has a Customer ervice Department to answer any

inquiries regarding applications and accessories.

To ensure you make full use of the possibilities offered by your CD-1 Indicator, please read the manual completely

before installation and operation.

1.1.1 Features

Major features include:

 1:10,000 maximum displayed resolution

 Durable AB plastic housing in a compact industrial design

 imple 2 function raised membrane buttons with Tare

 5-digit, 7-segment, 0.9 inch / 2.3 centimeter high LCD display

 Kilogram weight unit

 AC or battery power

 Load Cell Connector

 Wall mount hardware

 Battery saving Auto hut-off after five minutes of inactivity (when operated on batteries)

2. INSTALLATION

2.1 Unpacking and Checking

Open the package and remove the instrument and the accessories. Check the instrument for transport damage. Imme-

diately inform your Ohaus dealer if you have complaints or if parts are missing. Your CD-1 Indicator package should

contain:

 CD-1 Indicator  Instruction Manual  Mounting Bracket

 Mounting crews (2)  AC power adapter  Warranty card

 crew anchors (2)  Load Cell Connector

tore all parts of the packaging. This packaging ensures the best possible protection for the transport of your instrument.

CD-1 Indicator

2.2 Selecting the Location

The CD-1 Indicator should be used in an environment which is free from vibration, temperature or humidity extremes.

These factors will affect displayed weight readings. cale bases used with the CD-1 Indicator should be located on a

stable, level surface and kept away from vibrating sources such as large machinery. Maximum accuracy will be

achieved when the working area is clean and vibration free.

2.3 Cautionar Notes

 The CD-1 Indicator must not be operated in wet or hazardous areas.

 Before connecting the AC adapter, verify that the indicated voltage corresponds to the local mains voltage.

2.4 Connecting the CD-1 Indicator to a Scale Base

The scale base is connected to the round, 4-pin connector located on the right side of the CD-1 Indicator. The mating

connector supplied in the packaging must be attached to the load cell cable. lide the connector shell over the load cell

cable. Orient as shown in the illustration. Refer to the scale base manufacturer's information to determine the proper

load cell connections. older the load cell cable to the connector contacts according to table 2-1 and refer to the the

connector illustration.

NOTE: Any extra load cell connection wires should be isolated and insulated.

TABLE 2-1. LOAD CELL CONNECTION .

Connector Pin No. Connection

1 - Excitation

2 - ignal

3 + ignal

4 + Excitation

2.5 Connecting Power

The CD-1 Indicator may be operated using the supplied AC Adapter, or with 6 Alkaline "AA" batteries (not supplied).

2.5.1 AC Adapter

 Connect the AC Adapter connector to the receptacle located at the right-hand side of the CD-1 Indicator and

plug the adapter into a convenient outlet.

NOTICE:

The socket/outlet must be installed near

the equipment and shall be easil accessible.

2.5.2 Batter Installation

 Open the battery cover on the bottom of the housing.

 Insert 6 Alkaline "AA" batteries into position. Orient the batteries so that the positive (+) ends rest against the

reeds and the negative (-) ends against the springs.

NOTE: When the CD-1 Indicator is operated from batteries, the Auto hut-Off feature is automatically enabled to

extend battery life. When no activity occurs within a 5 minute period, the CD-1 Indicator shuts off. This

feature cannot be disabled.

AC ADAPTER CORD

CONNECTOR REAR VIEW

After soldering the wires to the contacts, thread the shell onto the receptacle. Tighten the strain relief clamp over the

load cell cable. Plug the connector into the mating connector on the Indicator and tighten the knurled nut.

STRAIN RELIEF

CLAMP KNURLED

NUT

SHELL CABLE RECEPTACLE

CONTACTS

CONNECTOR A EMBLY

CD-1 Indicator

No. Designation Function

1 Weight Display Displays current weight on scale.

2 Minus sign When displayed, indicates a negative value.

3 Down arrow When displayed, indicates reading is stable.

4Tare Menu button A short press enters the tare weight into memory.

A long press (2 seconds) enters the menu mode.

When in the menu mode, a short press changes the displayed menu or setting.

If a tare has been entered, a short press clears the tare when the platform is empty.

5 On/Zero Off button A short press turns the Indicator on when the Indicator is off.

A short press zeros the display when the Indicator is on. (If a Tare has been

entered, the tare is cleared and the display is zeroed).

A long press (2 seconds) turns the Indicator off.

When in the menu mode, a short press selects the displayed menu or setting.

6 kg arrow When displayed, indicates unit of measure (kilograms).

7 NET arrow When displayed, indicates reading is net weight.

3.1 Overview of Controls and Displa Functions

3. SETUP

2NET

CD-1 Indicator

3.2 Menu Structure

The following table illustrates the menu structure in the CD-1 Indicator.

CAL EtuP

Perform F (Full cale Capacity) submenu

g (Graduation size) submenu

CP (Calibration Point) submenu

CAL ? (Calibration ?)

3.3 Available Settings

Table 3-1 shown below indicates the available settings that can be made in the EtuP menu.

TABLE 3-1 ETUP.

Full Scale Graduation Size1,2,3 Calibration Point 1,2

Capacit 1(gxxxx) (CPxxxx)

(FSxxxx)

10.001 1

20.001, 0.002 1,2

30.001, 0.002 1, 2, 3

50.001, 0.002, 0.005 1, 2, 3, 5

60.001, 0.002, 0.005 1, 2, 3, 5, 6

10 0.001, 0.002, 0.005, 0.01 1, 2, 3, 5, 6, 10

15 0.002, 0.005, 0.01 1, 2, 3, 5, 6, 10, 15

20 0.002, 0.005, 0.01, 0.02 1, 2, 3, 5, 6, 10, 15, 20

25 0.005, 0.01, 0.02 1, 2, 3, 5, 6, 10, 15, 20, 25

30 0.005, 0.01, 0.02 1, 2, 3, 5, 6, 10, 15, 20, 25, 30

40 0.005, 0.01, 0.02 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40

50 0.005, 0.01, 0.02, 0.05 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50

60 0.01, 0.02, 0.05 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60

75 0.01, 0.02, 0.05 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75

100 0.01, 0.02, 0.05, 0.1 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100

120 0.02, 0.05, 0.1 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120

150 0.02, 0.05, 0.1 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150

200 0.02, 0.05, 0.1, 0.2 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200

250 0.05, 0.1, 0.2 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 250

300 0.05, 0.1, 0.2 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 250, 300

400 0.05, 0.1, 0.2 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 250, 300, 400

500 0.05, 0.1, 0.2, 0.5 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 250, 300, 400, 500

600 0.1, 0.2, 0.5 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 250, 300, 400, 500,

600

750 0.1, 0.2, 0.5 1, 2, 3, 5, 6, 10, 15, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 250, 300, 400, 500,

600, 750

1000 0.1, 0.2, 0.5, 1 1, 2, 3, 5, 6, 10, 20, 25, 30, 40, 50, 60, 75, 100, 120, 150, 200, 250, 300, 400, 500, 600,

750, 1000

Notes:

1 Full cale Capacity, Graduation ize and Calibration Point initial factory default settings are shown in bold.

2 Graduation ize and Calibration Point default settings for corresponding Full cale Capacity are shown underlined.

3 Graduation ize selections are limited to resolutions from 1:1000 to 1:10000.

CD-1 Indicator

3.4 Setup Procedure

The EtuP menu must be entered the first time the CD-1 Indicator is used to establish the scale base parameters.

Do not calibrate the Indicator prior to establishing parameters in the SEtuP menu.

This procedure sets up the operating parameters for the CD-1 Indicator to match the scale base.

 Press and hold the Tare Menu button. MENU is displayed

while the button is pressed and indicates CAL when released.

 Press the Tare Menu button again. EtUP is displayed.

 Press the On/Zero Off button to enter the EtUP menu. The display shows the Full cale

sub-menu F xxxx, where xxxx is the rated capacity of the scale base in kilograms. The last

selection is shown. The initial factory default setting F 1 is shown as an example.

 If the displayed setting is not the desired value, press the Tare Menu button to change to a

different setting. If the displayed setting is the desired value, press the On/Zero Off button

to store and move to the next sub-menu.

 The display shows the Graduation ize sub-menu gxxxx, where xxxx is the readability in

kilograms. The initial factory default setting is g0.001. When the Full cale value is

changed, the graduation value is automatically changed to the corresponding default value

(Refer to Table 3-1).

 If the displayed setting is not the desired value, press the Tare Menu button to change to a

different setting. If the displayed setting is the desired value, press the On/Zero Off button

to store and move to the next sub-menu.

 The display shows the Calibration Point sub-menu CPxxxx, where xxxx is the calibration

point in kilograms. The default setting is CP 1. When the Full cale value is changed, the

calibration point value is automatically changed to match the full scale value.

 If the displayed setting is not the desired value, press the Tare Menu button to change to a

different setting. If the displayed setting is the desired value, press the On/Zero Off button

to store and move to the next sub-menu. The display shows CAL ? (calibrate ?).

 After the Indicator has been properly set up to match the scale base parameters, calibrate

the unit before using. To enter calibration, press the On/Zero Off button and start at step

3 in the Calibration Procedure.

 If the menu settings were not changed, press the Tare Menu button to return to the weigh-

ing mode.

CD-1 Indicator

3.5 Calibration Procedure

The calibration procedure can be performed as often as necessary.

1. Make sure the scale base platform is empty, stable and level before starting calibration.

2. Press and hold the Tare Menu button. MENU is displayed while the

button is pressed and indicates CAL when released.

NOTE: The calibration process can be terminated at any time by pressing and holding the

On/Zero Off button until OFF is displayed.

3. Press the On/Zero Off button. -C- is displayed momentarily

(Indicator stores the zero load signal) followed by the calibration

weight value. CP 1 (1kg) is shown as an example.

4. Place the indicated calibration weight on the platform, then press the

On/Zero Off button. -C- is displayed (indicator stores the Cal point

load signal), followed momentarily by the indicated calibration

weight on the platform.

5. Remove the calibration weight from the scale base platform. The Indicator is now ready for

use.

Table des matières

Langues :

Autres manuels OHAUS Instrument de mesure

OHAUS

OHAUS i-DT33P Manuel utilisateur

OHAUS

OHAUS MC2000 Manuel utilisateur

OHAUS

OHAUS STARTER 300D Manuel utilisateur

OHAUS

OHAUS Ranger 3000 Series Manuel utilisateur

OHAUS

OHAUS 5000 Manuel utilisateur

OHAUS

OHAUS MB120 Manuel utilisateur

OHAUS

OHAUS MC2000 Manuel utilisateur

OHAUS

OHAUS Defender i-DT61PW Manuel utilisateur

OHAUS

OHAUS D52 Manuel utilisateur

OHAUS

OHAUS TD52 Manuel utilisateur

OHAUS

OHAUS MB90 Manuel utilisateur

OHAUS

OHAUS T71 Manuel d'utilisation et d'entretien

OHAUS

OHAUS a-AB23EC Manuel utilisateur

OHAUS

OHAUS a-AB33M1 Manuel utilisateur

OHAUS

OHAUS Defender 2000 Series Manuel utilisateur

OHAUS

OHAUS TD52 Manuel utilisateur

OHAUS

OHAUS 8000 Series Manuel utilisateur

OHAUS

OHAUS STARTER 3100C Manuel utilisateur

OHAUS

OHAUS TD52 Manuel utilisateur

OHAUS

OHAUS STARTER 2100 Manuel utilisateur

OHAUS

OHAUS STARTER 400D Manuel utilisateur

OHAUS

OHAUS AB23PH Manuel utilisateur

OHAUS

OHAUS ST400 Manuel utilisateur

OHAUS

OHAUS ST Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur