OHAUS T51 Manuel d'utilisation et d'entretien

Calibration Guide T51 Indicators

Ohaus Corporation www.ohaus.com iT51 Indicators Calibration Guide

T51 Indicators have three calibration processes: Zero, Span, and Linearity Calibration.

Follow the prompts for calibration mass values.

Ensure that the scale is level and stable during the entire calibration process.

Allow Indicator to warm up for five minutes after stabilizing to room temperature.

If the Calibration Menu is locked, the scale may be set in Legal For Trade mode.

To abort calibration, press the Exit button anytime during the calibration process.

Zero Calibration

Zero calibration uses one calibration point. This point is established with no weight on the scale.

Use this calibration method to adjust for a different pre-load without affecting the Span or

Linearity calibration.

Press and hold Menu until C.A.L. appears, then press Yes.

(LFt.NO appears briefly before C.A.L., if the Indicator is not in LFT mode.)

ZErO appears. Press Yes to initiate Zero Calibration.

The display flashes 0 and the calibration unit. Press Yes to establish the

zero point.

The display shows --C-- while the zero point is established.

When zero calibration is completed, the display shows dONE.

Then the scale exits to the active weighing mode and displays the actual

weight value.

Span Calibration

Span Calibration uses two points to adjust the Indicator. The first point is the zero value, where

there is no weight on the scale. The second point is the Span value, where a calibration mass

is placed on the scale.

Press and hold Menu until MENU appears. Press Yes.

(LFt.NO appears, then C.A.L., if the Indicator is not in LFT mode.)

Press Yes. SPAN appears. Press Yes to initiate Span Calibration.

The display flashes the span calibration point. Place the specified weight

on the scale and press Yes.

(Press No to increment the selections, or Back to decre

ment the selections.

When desired value appears, place specified weight on scale; press Yes.)

The display shows --C-- while the span point is established.

When the span point is established, the display flashes 0.

Remove the weight from the scale; press Yes to establish the zero point.

T51 Indicators Calibration Guide

T51 Indicators Calibration Guide ii Ohaus Corporation www.ohaus.com

Span Calibration continued

The display shows --C-- while the zero point is established.

When span calibration is completed, the display shows dONE.

The scale exits to the active weighing mode and displays the actual weight

value.

Linearity Calibration

Linearity calibration uses three calibration points: the full calibration point is selectable by the

user. The mid-calibration point is automatically set at half of the full calibration point.

The zero calibration point is established with no weight on the scale.

Press and hold Menu until C.A.L. appears, then press Yes.

(LFt.NO appears briefly before C.A.L., if the Indicators is not in LFT mode.)

ZERO appears. Press No. SPAN appears. Press No. Linearity appears.

Press Yes to initiate Linearity Calibration.

The display flashes the full calibration point and calibration unit.

Place the specified weight on the scale and press Yes.

(Press No to increment the selections, or Back to decrement the selections.

When desired value is displayed, place the specified weight on the scale and

press Yes.)

The display shows --C-- while the full calibration point is established.

When the full calibration point is established, the display flashes the

mid-calibration point. Place the specified weight on the scale and press Yes.

The display shows --C-- while the mid-calibration point is established.

When the mid-calibration point is established, the display flashes 0.

Remove the weight from the scale; press Yes to establish the zero point.

The display shows --C-- while the zero point is established.

When linearity calibration is completed, the display shows dONE.

The scale exits to the active weighing mode and displays the actual weight

value.

*8025305*

P/N 80253035

Table des matières

Autres manuels OHAUS Instrument de mesure

OHAUS

OHAUS starter 3100 Manuel utilisateur

OHAUS

OHAUS TD52 Manuel utilisateur

OHAUS

OHAUS STARTER 5000 Manuel utilisateur

OHAUS

OHAUS MB45 Manuel utilisateur

OHAUS

OHAUS starter 3100 Manuel utilisateur

OHAUS

OHAUS a-AB33M1 Manuel utilisateur

OHAUS

OHAUS ST20C-A Manuel utilisateur

OHAUS

OHAUS STARTER 3100C Manuel utilisateur

OHAUS

OHAUS i-DT33P Manuel utilisateur

OHAUS

OHAUS TD52 Manuel utilisateur

OHAUS

OHAUS ST300-B Manuel utilisateur

OHAUS

OHAUS MB120 Manuel utilisateur

OHAUS

OHAUS STARTER 2100 Manuel utilisateur

OHAUS

OHAUS MB35 Manuel utilisateur

OHAUS

OHAUS MB23 Manuel utilisateur

OHAUS

OHAUS ST20C-A Manuel utilisateur

OHAUS

OHAUS D52 Manuel utilisateur

OHAUS

OHAUS ST Series Manuel utilisateur

OHAUS

OHAUS Defender I-D33P15B1R1 Manuel utilisateur

OHAUS

OHAUS STARTER 2100 Manuel utilisateur

OHAUS

OHAUS ST20D Manuel utilisateur

OHAUS

OHAUS STARTER 5000 Manuel utilisateur

OHAUS

OHAUS ST300 Manuel utilisateur

OHAUS

OHAUS i-DT33XW Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur