Numatic TTB-665 Manuel utilisateur

TTB-665 OPERATION MANUAL

the knowledge is in our hands

LAST PAGE

RETURN TO MENU

TWINTEC 665

TTB 665 OPERATION - INFORMATION INDEX

1. Part Identification Diagram

2. Basic Operation Instructions

3. Dos and Donts

4. Fitting The Brush / Dri e Board

5. Filling The Clean Water Tank

6. Water Release Controls

7. Adjusting The Handle Height

8. Handle Controls

9. Emptying The Top Tank

10. Emptying The Bottom Tank

11. Cleaning The Separator Filter

12. Cleaning The Top Tank Filter

13. Cleaning The Bottom Tank Filter

14. Daily Maintenance Routine

15. Charging the Batteries

16. Changing The Squeegee Blades

17. Problem Sol ing

TWINTEC 665

TTB 665 OPERATION - PART IDENTIFICATION

HANDLE TOP (DIRTY

WATER) TANK

BOTTOM (CLEAN

WATER) TANK

SEPARATOR

SQUEEGEE TOOL

BRUSHES

CHARGING LEAD

CHASSIS BRUSH DECK

TWINTEC 665

TTB 665 OPERATION - OPERATING INSTRUCTIONS

1. Ensure that charging lead has been disconnected

2. Ensure that the isolator pin is in place

3. Fit pad & drive boards / scrubbing brushes

4. Unclip deck so that the pads / brushes are positioned flat to the floor

5. Lower the squeegee blade so that it is positioned flat to the floor

6. Fill bottom tank with clean water and detergent

7. Ensure that water on/off control is set at appropriate position

8. Ensure that top tank is empty

9. Ensure that separator is fitted correctly

10. Ad ust handle height to suit

11. Stand behind the machine

12. Press both of the black rubber buttons on the handle display

13. Press and hold in the yellow button on the rear of the handle and at the same

time squeeze the triggers on the handle. Release the yellow button

14. Push the machine in the direction in which you want to clean, holding in the black

triggers

15. When you want the machine to stop, release triggers

TWINTEC 665

TTB 665 OPERATION - DOS AND DONTS

DO ensure only competent persons unpack and assemble the machine

DO keep the machine clean

DO keep the brushes in good condition

DO replace any worn or damaged parts immediately

DO ensure that the working area is clear of obstructions

DO ensure that the working are is well illuminated

DO follow all the instructions supplied

DO ensure that if using a pad, it is washed after each use

DONT use steam cleaners or pressure washers to clean the machine

DONT use the machine with only one brush or drive board

DONT use the machine outdoors in the rain

DONT attempt machine maintenance or cleaning with the isolator pin intact

DONT allow any inexperienced repairs

DONT leave the brush or pad on the machine when not in use

DONT allow the machine to be used by inexperienced or unauthorised personnel

DONT lift or pull the machine by any of the operating triggers

DONT leave the machine running in one spot, turn off if not being used

DONT leave the brush or pad on the machine overnight, they will flatten

WARNING

It is essential that the equipment is correctly assembled and operated in accordance

with current safety regulations. When using the equipment always ensure that all

necessary precautions are taken to guarantee the safety of the operator and any other

persons who may be affected. Wear non-slip footwear when scrubbing. Always use a

respiratory mask in dusty environments. The use of other accessories may affect the

safety of the scrubber dryer. A full range of brushes and other accessories are available

from Numatic International.

TWINTEC 665

TTB 665 OPERATION - FITTING THE BRUSH / DRIVE BOARD

1. MACHINE SHOWN WITH

BOTH BRUSHES.

2. POSITION BRUSHES ONTO

THE GEARBOX WITH THE 3

INDENTATIONS ALLIGNING

WITH THE 3 TABS. TURN

ANTI-CLOCKWISE TO LOCK

BRUSH IN PLACE.

3. THE BRUSHES WILL NOW

BE LOCKED IN PLACE AND

READY FOR USE.

NOTE: WHEN USING DRIVE BOARDS FOLLOW THE SAME INSTRUCTIONS

TO FIT DRIVE BOARDS AND THEN FIX PADS CENTRALLY ONTO BOARDS.

TWINTEC 665

TTB 665 OPERATION - FILLING THE CLEAN WATER TANK

1. OPEN THE FILLING CAP ON

THE FRONT OF THE BOTTOM

TANK, LEAVING THE FILTER

IN PLACE TO REMOVE ANY

DEBRIS.

2. SIMPLY POUR WATER

WITH A MIX OF YOUR CHO-

SEN DETERGENT INTO THE

SPOUT ON THE FRONT OF THE

BOTTOM TANK.

TWINTEC 665

TTB 665 OPERATION - WATER RELEASE CONTROLS

1.THE WATER CONTROL IS

LOCATED AT THE REAR OF

THE MACHINE (BOTTOM LH)

2. WITH THE TAP IN ITS

HORIZONTAL POSITION

THERE WILL BE NO WATER

FLOW.

3.IN ORDER TO RELEASE

WATER, PUSH TAP TOWARDS

THE FLOOR.

NOTE:

FULL WATER FLOW IS 2.5

LITRES PER MINUTE. THIS

TAP CAN BE ADJUSTED ANY-

WHERE BETWEEN NO FLOW

AND FULL FLOW TO ACHIEVE

THE DESIRED FLOW FOR THE

TASK BEING UNDERTAKEN.

TWINTEC 665

TTB 665 OPERATION - ADJUSTING THE HANDLE HEIGHT

1. SQUEEZE THE HANDLE

ADJUSTMENT LEVER ON

THE RIGHT HAND SIDE.

2. OPERATION IS EASIEST

WITH THE HANDLE AT WAIST

HEIGHT.

3. FOR TURNING IN TIGHT

SPACES OR FOR LESS FLOOR

PRESSURE, PUT THE HANDLE

INTO A HIGHER POSITION.

NOTE:

THE BEST WAY TO SCRUB IS

TO FIND A HANDLE LEVEL AT

WHICH YOU FEEL COMFORT-

ABLE AND CAN EASILY CON-

TROL THE MACHINE AROUND

CORNERS AND OBSTACLES

AS WELL AS IN A STRAIGHT

LINE.

THE HIGHER THE HANDLE

LEVEL, THE LESS FLOOR

PRESSURE AND VICE VERSA.

TWINTEC 665

TTB 665 OPERATION - HANDLE CONTROLS

WATER ON / OFF VACUUM ON / OFF

WATER

BATTERY

FULLY

CHARGED

BATTERY

TO EMPTY

BATTERY

EMPTY

VACUUM

BRUSH

OFF

Autres manuels Numatic Machine de plancher

Numatic

Numatic TTB 4055/100 Manuel utilisateur

Numatic

Numatic NuSpeed NR-1500 Manuel utilisateur

Numatic

Numatic NuSpeed NR-1500 Manuel utilisateur

Numatic

Numatic HFS 1015 Manuel utilisateur

Numatic

Numatic TTV 4555 Manuel utilisateur

Numatic

Numatic HNS1550G Manuel utilisateur

Numatic

Numatic NPR 1515/S Manuel utilisateur

Numatic

Numatic CRO 8055 Manuel utilisateur

Numatic

Numatic floorcare tt 1840 Manuel utilisateur

Numatic

Numatic SPN 1804 Manuel utilisateur

Numatic

Numatic NuSpeed NR-1500 Manuel utilisateur

Numatic

Numatic NR-1500M Manuel utilisateur

Numatic

Numatic TTB 4045/100 Manuel utilisateur

Numatic

Numatic SQFM 4325 Manuel utilisateur

Numatic

Numatic TTB 4055/100T Manuel utilisateur

Numatic

Numatic LoLine NLL 332 Manuel utilisateur

Numatic

Numatic TRO 650 Manuel utilisateur

Numatic

Numatic LoLine NLL 415 Manuel utilisateur

Numatic

Numatic NR 1500 Manuel utilisateur

Numatic

Numatic TWINTEC CABLE TT4055 Manuel d'installation et d'exploitation

Numatic

Numatic TTB 6055 Manuel utilisateur

Numatic

Numatic TT4045G Manuel utilisateur

Numatic

Numatic TTB 1840 Manuel utilisateur

Numatic

Numatic TwinTec 455 Manuel utilisateur

Manuels Machine de plancher populaires d'autres marques

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manuel utilisateur

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manuel utilisateur

Mytee

Mytee 8070 Mytee-Lite Manuel utilisateur

Kärcher

Kärcher B 140 R Manuel utilisateur

Triple S

Triple S Ace 26T1 Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance SW 750 Manuel utilisateur

Tornado

Tornado Marathon 2000 98190 Manuel

Windsor

Windsor ADMIRAL Admiral 8 Manuel utilisateur

Tennant

Tennant 8210D Manuel utilisateur

Nobles

Nobles Frontier Manuel du produit

lavina

lavina 21-X Manuel utilisateur

KENT

KENT Edge 28B Manuel utilisateur

Tennant

Tennant 215 Manuel du produit

Windsor

Windsor BDP 51/2000C Manuel utilisateur

CleanFreak

CleanFreak DURA-18HD Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guide de l'administrateur

BETCO

BETCO PB24 Manuel utilisateur

IPC

IPC CT51-71 BT Manuel utilisateur