Numatic SPN 1804 Manuel utilisateur

Accessories are NOT supplied

with this trolley.

Owner Instructions

Original Instructions

Warning! Read instructions before using the machine

www.numatic.com

SPN 1804

Unpacking the machine.

1 2

Ensure the battery has been charged before use.

Fit the Battery

Fit the battery to the machine and plug in the motorised trolley.

1 2

Always ensure the machine is switched off prior to any maintenance.

Using the Machine

Main Control On / Off Key

Machine Off Isolator Button

Forward Switch

Reverse Switch

Insert key (Fig 1) and turn 900

clockwise to the ‘ON’ position.

Emergency Stop

Machine Charging

To ensure your machine remains at its maximum efciency and prolong

your battery life, please follow the simple steps below:

Under normal daily usage:

Recharge battery after each use

regardless of machine operation

time.

Connect the charger unit to the

battery and plug the charger into a

suitable power supply.

The battery charge state is shown by the light

sequence on the front of the charger.

Signal (LED) Meaning

Red LED on First phase of charge in progress

Yellow LED on Second phase of charge in progress

Green LED on

End of charge or maintenance phase

Disconnect from power supply

Switch power supply, Off then On, to

restart the charging cycle

Red LED ashing

Unsuitable battery or

charging malfunction

Safety timer exceeded

Internal short circuit

Disconnect from power supply

Switch power supply, Off then On, to

restart the charging cycle

Yellow LED ashing Battery not connected

INITIAL TEST

Green LED with 2 ashes Battery charger congured for recharging

Gel or AGM batteries

Red LED with 2 ashes Battery charger congured for recharging

Lead-acid (Wet) traction batteries

The battery meter displays the charge level of the battery; when fully charged,

all meter lights are illuminated.

The battery supplied for this machine allows for a run time of 180 mins approx,

when fully charged.

Charge time is approximately 6 hours.

Spare replacement batteries are available from your supplier.

See SPN 1804 Spares list for part numbers.

The SPN 1804 trolley comes with its own stand-alone charger.

Insert the charging lead required for your country into the charger.

Connect the charger to a suitable power supply.

Recharge the machine fully after its last use.

Do not leave the machine in a discharged state.

If the machine will be standing unused for a period of 30 days or more, then

batteries must be fully charged.

Once mains power is connected the red charging indicator will illuminate.

To ensure a full charge, the battery should be left for a period of 6 hrs.

Once fully charged, disconnect the charging lead from both the power

supply and the machine.

Under abnormal use;

i.e. leaving the machine without charging for a period of time, we advise

that you disconnect the battery from the machine.

Note:

Batteries should be recharged every three months.

Charge fully the day before you start using the machine again.

Removing the battery pack fuse

The battery pack comes with a 40 amp safety fuse tted

Replace the fuse using (208526) Numatic approved part.

WEEE (Waste, Electrical and Electronic Equipment)

SPN Trolley and packaging should be sorted for environmentally-friendly recycling.

Only for EU countries.

Do not dispose of Trolley into household waste.

According to the European Directive 2002/96/EC on waste electrical electronic equipment and

its incorporation into national law.

SPN Trolleys that are no longer suitable for use must be separated, collected and sent for

recovery in an environmentally-friendly manner.

Safety Critical Component

Charging Lead:

H05VV-F x 1.0 mm2x 3 core

Battery Charger:

100 - 240 Volt (50-60 Hz)

PPE

(Personal protective equipment) that may be required for certain operations).

Ear Protection Safety Footwear Head Protection Safety Gloves

Dust/Allergens

Protection

Eye Protection Protective

Clothing

Hi-Vis Jacket

Caution

oorsign

Note:

A risk assessment should be conducted to determine which PPE should be worn.

About the Machine

Company Name & Address

Machine Description

Voltage Frequency

Power rating

Max Gradient

Weight (ready to use)

CE Mark

WEEE Logo

Machine yr/wk Serial number

Rating Label

3 4

Read the instruction manual before using the appliance.

Do not use on surfaces having a gradient exceeding that marked on the appliance.

The machine is not to be stored outdoors in wet conditions.

This machine is for indoor use only.

As with all electrical equipment care and attention must be exercised at all times during

its use, in addition to ensuring that routine and preventative maintenance is carried out

periodically in order to ensure its safe operation.

Failure to carry out maintenance as necessary, including the replacement of parts to the

correct standard could render this equipment unsafe and the manufacturer can accept no

responsibility or liability in this respect.

When ordering spare parts always quote the Model Number / Serial Number specied on the

Rating Plate.

Warning: do not use on slopes.

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

NOTE:

This machine is also suitable for commercial use, for example in hotels, schools, hospitals,

factories, shops and ofces for other than normal housekeeping purposes.

DO’S AND DON’TS:

DO ensure only competent persons unpack/assemble the machine.

DO keep your machine clean.

DO replace any worn or damaged parts immediately.

DO regularly examine the power cord for damage, such as cracking or ageing.

If damage is found, replace the cord before further use.

DO only replace the power cord with the correct Numatic approved replacement parts.

DO ensure that the work area is clear of obstructions and / or people.

DO ensure that the working area is well illuminated.

DON’T use steam cleaners or pressure washers to clean the machine or use in the rain.

DON’T attempt machine maintenance or cleaning unless the power plug has been

removed from the supply outlet.

DON’T allow any inexperienced repairs. Call the experts.

DON’T strain cable or try to unplug by pulling on cable.

DON’T allow the machine to be used by inexperienced or unauthorised operators or

without appropriate training.

DON’T expect the machine to provide trouble-free, reliable operation unless main-

tained correctly.

DON’T remove the handle from the machine except for service and repair.

ORIGINAL INSTRUCTIONS

READ MANUAL BEFORE USE

Information for Motorised trolley

Component Interval Inspect for

Charging Lead DAILY Scufng, cracks, splits, conductors showing

CAUTION

DON’T

WARNING

It is essential that this equipment is correctly assembled and operated in accordance

with current safety regulations.

When using the equipment always ensure that all necessary precautions are taken to

guarantee the safety of the operator and any other persons who may be affected.

The machine, while charging, must be positioned so that the mains plug is easily accessible.

When cleaning, servicing or maintaining the machine, replacing parts or converting to another

function the power source shall be switched off.

Battery operated machines shall be disconnected by removing the Battery pack.

Operators shall be adequately instructed as to the correct use of the machine.

PRECAUTIONS WHEN WORKING WITH BATTERIES

1. Always wear protective clothing e.g. face visor, gloves and overalls when working with batteries.

2. Whenever possible always use a properly designated and well-ventilated area for charging. Do

not smoke or bring naked ames into the charging area.

3. Remove any metallic items from hands, wrists and neck i.e. rings, chains etc. before working on

a battery.

4. Never rest tools or metallic objects on top of the battery.

5. When charging is complete disconnect from the mains supply.

6. The battery must be removed from the machine before it is scrapped.

7. The machine must be disconnected from the supply when removing the battery.

8. The batteries are to be disposed of safely and in accordance with the battery directive.

9. Only use genuine NUMATIC replacement batteries.

10. Do not allow the batteries to become fully discharged; it may not be possible to recharge them.

11. The batteries tted to this product are Valve Regulated Lead Acid (VRLA) gel electrolyte type.

The tting of any other type of battery may cause a safety hazard.

BATTERY CARE

1. Always recharge the batteries after use. This can be done at any time it is not necessary to wait

until they are fully discharged; they do not develop a “memory”.

2. Leaving the charger to operate for a minimum of 4 hours after the green light has come on, at

least weekly, will prolong battery life.

3. Do not store the machine with the batteries discharged.

WARNING

Table des matières

Autres manuels Numatic Machine de plancher

Numatic

Numatic TTB 1117/100 Manuel utilisateur

Numatic

Numatic TT-3450S Manuel utilisateur

Numatic

Numatic TTB-1620 Manuel utilisateur

Numatic

Numatic TTB 4055/100 Manuel utilisateur

Numatic

Numatic TTB-1620/100 Manuel utilisateur

Numatic

Numatic TTV 678-300 Manuel utilisateur

Numatic

Numatic LoLone NLL Series Instructions de montage

Numatic

Numatic HFS 1015 Manuel utilisateur

Numatic

Numatic TWINTEC CABLE ET4045 Manuel d'installation et d'exploitation

Numatic

Numatic ET 4045 Manuel utilisateur

Numatic

Numatic LOLINE HLL 332 Manuel utilisateur

Numatic

Numatic TTB 4055/100T Manuel utilisateur

Numatic

Numatic HNS1550G Manuel utilisateur

Numatic

Numatic NPR 1515/S Manuel utilisateur

Numatic

Numatic NR-1500M Manuel utilisateur

Numatic

Numatic HNS1550 Manuel utilisateur

Numatic

Numatic NuSpeed NR-1500 Manuel utilisateur

Numatic

Numatic TwinTec 455 Manuel utilisateur

Numatic

Numatic NPR 1515/S Manuel utilisateur

Numatic

Numatic NR 1500 Manuel utilisateur

Numatic

Numatic NuSpeed NR-1500 Manuel utilisateur

Numatic

Numatic LoLine NLL 332 Manuel utilisateur

Numatic

Numatic TTB-455 Manuel utilisateur

Numatic

Numatic TTB 4055 Manuel utilisateur

Manuels Machine de plancher populaires d'autres marques

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manuel utilisateur

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manuel utilisateur

Mytee

Mytee 8070 Mytee-Lite Manuel utilisateur

Kärcher

Kärcher B 140 R Manuel utilisateur

Triple S

Triple S Ace 26T1 Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance SW 750 Manuel utilisateur

Tornado

Tornado Marathon 2000 98190 Manuel

Windsor

Windsor ADMIRAL Admiral 8 Manuel utilisateur

Tennant

Tennant 8210D Manuel utilisateur

Nobles

Nobles Frontier Manuel du produit

lavina

lavina 21-X Manuel utilisateur

KENT

KENT Edge 28B Manuel utilisateur

Tennant

Tennant 215 Manuel du produit

Windsor

Windsor BDP 51/2000C Manuel utilisateur

CleanFreak

CleanFreak DURA-18HD Manuel utilisateur

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guide de l'administrateur

BETCO

BETCO PB24 Manuel utilisateur

IPC

IPC CT51-71 BT Manuel utilisateur