Ntron 105M12 Manuel utilisateur
(Revised 2010-11-15)
1
105M12 and 108M12
Industrial Ethernet Switches
Installation
Guide
(Revised 2010-11-15)
2
105M12 & 108M12 Industrial Ethernet Switches Installation Guide
(Revised 2010-11-15)
3
Copyright, © N-TRON Corp., 2008
820 S. University Blvd., Suite 4E
Mobile, AL 36609 USA
All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-TRON
Corp. is prohibited, except as allowed under copyright laws.
Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos
or other designations mentioned herein are trademarks of their respective owners.
The information contained in this document is subject to change without notice. N-TRON Corp. makes no
warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability or fitness for a particular purpose. In no event shall N-TRON Corp. be liable for any
incidental, special, indirect or consequential damages whatsoever included but not limited to lost profits
arising out of errors or omissions in this manual or the information contained herein.
(Revised 2010-11-15)
4
SAFETY WARNINGS
ELECTRICAL SAFETY
WARNING: Disconnect the power cable before removing the end plates.
WARNING: Do not operate the unit with the end plates removed.
WARNING: Properly ground the unit before connecting anything else to the unit. Units not properly
grounded may result in a safety risk and could be hazardous and may void the warranty. See the
grounding technique section of this user manual for proper ways to ground the unit.
WARNING: Do not work on equipment or cables during periods of lightning activity.
WARNING: Do not perform any services on the unit unless qualified to do so.
WARNING: Observe proper DC Voltage polarity when installing power input cables. Reversing
voltage polarity can cause permanent damage to the unit and void the warranty.
HAZARDOUS LOCATION INSTALLATION REQUIREMENTS
1. WARNING: Explosion hazard. Do not remove or replace the device unless power has been switched off
or the area is known to be non-hazardous.
2. WARNING: Explosion hazard. Do not disconnect while the circuit is live or unless the area is known to
be non-hazardous..
3. WARNING: Explosion hazard. Substitution of components may impair suitability for Class I, Division 2.
4. WARNING: Install only in accordance with Local & National Codes of Authorities Having Jurisdiction.
5. Class I, Div 2 installations require that all devices connected to this product must be UL listed for the area in
which it is installed.
6. Limited Operating Voltage: 12-30V for Class I, Div 2 installations.
7. This equipment is suitable for use in Class I, Div 2, Groups A, B, C, and D, or non-hazardous locations
only.
(Revised 2010-11-15)
5
105M12 Industrial Ethernet Switch
The 105M12 is an unmanaged industrial Ethernet switch providing five Fast Ethernet copper ports in an
IP65/IP67 rated enclosure for protection against temporary immersion in water. The switch provides
Category-5 compliant 10/100BaseTX connections with IP65/67 rated M12 D-code connectors for high
performance network design, and hub/repeater upgrades. The switch is capable of auto negotiating 10/100
Mb and half/full duplex communications.
108M12 Industrial Ethernet Switch
The 108M12 is an unmanaged industrial Ethernet switch providing eight Fast Ethernet copper ports in an
IP65/IP67 rated enclosure for protection against temporary immersion in water. The switch provides eight
Category-5 compliant 10/100BaseTX connections with IP65/67 rated M12 D-code connectors for high
performance network design, and hub/repeater upgrades. The switch is capable of auto negotiating 10/100
Mb and half/full duplex communications.
Key Features
IP65 Rated for protection against low pressure jets of water from any direction
IP66 Rated for protection against high pressure jets of water from any direction
IP67 Rated for protection against temporary immersion in water
Full IEEE 802.3
Extended Environmental Specifications
Support for Full/Half Duplex Operation
Auto MDI/MDIX (crossover) on all ports
LED Link/Activity Status Indication
Autonegotiation, Autosensing Speed, Duplex, and Flow Control
Up to 1.0 Gb/s maximum throughput for the 105M12 and 1.6 Gb/s for the 108M12 model
Redundant power input
Bulk head mountable (optional Industry Standard 35mm DIN rail mounting available)
108M12-HV Only
(Revised 2010-11-15)
6
INGRESS PROTECTION IP67
The classification of degrees of protection provided by the enclosures is defined by IEC 60529. Each rating is
defined by specific tests.
The IP number is comprised of two numbers, the first referring to the protection against solid objects and the
second against fluids. The higher the number, the better the device is protected against contact with moving
parts and the harmful entry of various forms of moisture.
1st IP
Protection against ingress of solids
2nd IP
Protection against ingress of liquids
0
No protection
0
No protection
1
Protected against solid objects over 50mm e.g. hands,
large tools.
1
Protected against vertically falling drops of water.
2
Protected against solid objects over 12mm e.g. hands,
large tools.
2
Protected against direct sprays of water up to 15° from
vertical.
3
Protected against solid objects over 2.5mm e.g. wire,
small tools.
3
Protected against direct sprays of water up to 60° from
vertical.
4
Protected against solid objects over 1.0mm e.g. wires.
4
Protected against water sprayed from any direction.
Limited ingress permitted.
5
Limited protection against dust ingress (no harmful
deposit)
5
Protected against low pressure water jets from any
direction. Limited ingress permitted.
6
Totally protected against dust ingress.
6
Protected against high pressure water jets from any
direction. Limited ingress permitted.
7
Protected against temporary immersion between 15cm
to 1m.
8
Protected against long periods of immersion under
pressure.
The 105M12 and 108M12 Industrial Ethernet Switches are fully protected against dust and will remain sealed
when immersed in water to a depth of 1 meter for 1 hour when all the ports are properly mated or sealed.
These IP67 caps seal off the unused ports protecting them from dirt, water, oil or any other
contaminants which might be present in the close proximity of the switch.
PACKAGE CONTENTS
Please make sure the Ethernet Switch package contains the following items:
1. 105M12 or 108M12 Industrial Ethernet Switch
2. Product CD
UNPACKING
Remove all the equipment from the packaging, and store the packaging in a safe place. File any damage
claims with the carrier.
(Revised 2010-11-15)
7
INSTALLATION
Read the following warning before beginning the installation:
WARNING
Never install or work on electrical equipment or cabling during periods of lightning activity.
BULKHEAD MOUNTING
The following are the mechanical dimensions and drill hole placements to consider when mounting the
105M12 and 108M12 Industrial Ethernet Switches:
(Revised 2010-11-15)
8
FRONT PANEL
LNK/ACT Link/Activity LED
M12 D-Coded Female Ports All ports are Auto sensing 10/100BaseTX Connections
M12 A-Coded Male Port Redundant Power Input (10-30VDC)
Green LED lights when Power is connected
LED’s: The table below describes the operating modes:
LED
Color
Description
ON
Power is Applied.
OFF
Power is OFF.
LNK/ACT
ON
Link established, no Activity on cable.
BLINKING
Link established, Activity on cable
OFF
No link established
(Revised 2010-11-15)
9
APPLYING POWER
The M12 A coded power connector is keyed, where the mating connection from the power supply can
be made only when the male and female ends are lined up properly.
When the power is first connected all LED’s will flash ON Momentarily.
Verify the Power LED stays ON (GREEN).
Note: Either V1or V2can be connected to power for minimal operation. For redundant power
operation, V1and V2 must be connected to separate DC Voltage sources. The power cord should be
limited to less than 10 meters in order to ensure optimum performance.
Recommended 24V DC Power Supplies, similar to:
100VAC/240VAC:
N-Tron NTPS-24-1.3, DC 24V/1.3A
(Revised 2010-11-15)
10
N-TRON 105M12 AND 108M12 GROUNDING TECHNIQUES
Drain wire with lug connecting switch chassis to known grounding point.
CONNECTING THE UNIT
For 10Base-T ports, plug a Category 3 (or greater) twisted pair cable into the M12 connector. For
100Base-T ports, plug a Category 5 (or greater) twisted pair cable into the M12 connector. Connect the
other end to the far end station. Verify that the LNK LED’s are ON once the connection has been
completed. To connect any other port to another Switch or Repeater, use a standard Cat5 straight
through or crossover cable.
Warning: Creating a port to port connection on the same switch (i.e. loop) is an illegal operation and
will create a broadcast storm which will crash the network!
TROUBLESHOOTING
1. Make sure the (Power LED) is ON.
2. Verify that Link LED’s are ON or BLINKING for connected ports.
3. Verify cabling used between stations.
4. Verify that cabling is Category 5 (or greater) for 100Mbit Operation.
SUPPORT
Contact N-TRON Corp. at:
TEL: 251-342-2164
FAX: 251-342-6353
www.n-tron.com
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Ntron Changer
Ntron
Ntron 900 Manuel d'utilisation
Ntron
Ntron 7010TX Series Instructions d'installation et d'utilisation
Ntron
Ntron 7506GX2 Series Instructions d'installation et d'utilisation
Ntron
Ntron 702-W Manuel du propriétaire
Ntron
Ntron 7014TX Instructions d'installation et d'utilisation
Ntron
Ntron 708FX2 Manuel utilisateur
Ntron
Ntron 100-POE4-MDR Instructions d'installation et d'utilisation
Ntron
Ntron 604MFX-ST Manuel
Ntron
Ntron 7018TX Instructions d'installation et d'utilisation
Ntron
Ntron 9000 Series Instructions d'installation et d'utilisation
Ntron
Ntron 108M12 Manuel utilisateur
Ntron
Ntron 708TX Instructions d'installation et d'utilisation
Ntron
Ntron 302MC-XX Manuel utilisateur
Ntron
Ntron 709FX Series Instructions d'installation et d'utilisation
Ntron
Ntron 308FX2 Instructions d'installation et d'utilisation
Ntron
Ntron 509FX Manuel utilisateur
Ntron
Ntron 105FX-POE Instructions d'installation et d'utilisation
Ntron
Ntron 7014 Series Guide de démarrage rapide
Ntron
Ntron 7900 Series Instructions d'installation et d'utilisation
Ntron
Ntron 508TX Manuel utilisateur
