Ntron 7014 Series Guide de démarrage rapide

N-Tron 7014 Series Firmware Upgrade Procedure

TFTP Method:

Please refer to the user's guide found the ProductCD or on-line at:

www.n-tron.com/html/tech_docs.html

Note: Although the download speed may be quicker, this method requires third party TFTP server

software to be installed on a PC connected to the LAN. When updating a few units, you may find

it quicker to simply use the Serial Port method listed below.

Serial/COM Port method:

Save the included 7014 Series Flash Image file to a local drive location such as c:\

(115200, 8, N, 1, No Flow Control)

Hit <ENTER> to login [Enter]

Allowing Serial Session

Product Name : N-TRON 7000 Series

Product Configuration : 7014xxx

Product Software Version : x.x.x

Product BOOT ROM Version : LOADER1.20

Product Build Date : xxx xx xxxx at xx:xx:xx

Product CopyRight : N-TRON Corp.

Product URL : http://www.n-tron.com

N-TRON Managed Switch

Password: admin [Enter]

N-TRON/Admin#[1]> image [Enter]

N-TRON/Admin#[2]image> download [Enter]

Download Image Using xModem (Serial Download) [y/n] y [Enter]

Start Image Download Using xModem

xModem Download Starts From HERE.

From the Transfer Pull down menu in

Hyper terminal select --> Send File... -

-> Browse to select saved flash file -->

Set Transfer to xModem --> Send

Button as shown to the right:

Once you have selected the file

location and xModem protocol, you

must click the Send button with your

mouse to begin downloading the

image to the switch.

Checking the Image length and verifying checksum

Checksum Satisfied, Saving image to flash..

Downloaded Image Size:[xxxxxxx] Bytes

May take a few Minutes.....

...........................................................................................................................................................

.......................................................................................................

Do you Want to Restart the System Now: [y/n] y [Enter]

Do you Want to Save the Configuration: [y/n] n [Enter]

Device is Going for Reboot....

Once unit has rebooted, manually cycle the power on the 7014 and verify the update has been

processed.

Hit <ENTER> to login [Enter]

Allowing Serial Session

Product Name : N-TRON 7000 Series

Product Configuration : 7014xxx

Product Software Version : x.x.x

Product BOOT ROM Version : LOADER1.20

Product Build Date : xxx xx xxxx at xx:xx:xx

Product CopyRight : N-TRON Corp.

Product URL : http://www.n-tron.com

N-TRON Managed Switch

Password: admin [Enter]

N-TRON/Admin#[1]> config erase [enter]

Load Factory Default Setting? [y/n] y [enter]

Keep IP, SubNet and Gateway Addresses? [y/n] n [enter]

Restart the switch to effect this change

N-TRON/Admin#[2]config> (manually cycle power of switch)

Re-Configure the IP Address and Subnet Mask of the 7014 in CLI

Note: The factory default IP Configuration of this switch is:

IP: 192.168.1.201

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

Hit <ENTER> to login [Enter]

Allowing Serial Session

Product Name : N-TRON 7000 Series

Product Configuration : 7014xxx

Product Software Version : x.x.x

Product BOOT ROM Version : LOADER1.20

Product Build Date : xxx xx xxxx at xx:xx:xx

Product CopyRight : N-TRON Corp.

Product URL : http://www.n-tron.com

N-TRON Managed Switch

Password: admin [Enter]

N-TRON/Admin#[1]> system [Enter]

N-TRON/Admin#[2]system> set [Enter]

N-TRON/Admin#[3]system/set> ip 192.168.1.210 255.255.255.0 [Enter] (sample settings)

The IP Address has been changed to : 192.168.1.133

The Subnet Mask has been changed to : 255.255.255.0

Do you Want to Restart the System Now: [y/n] y [Enter]

Do you Want to Save the Configuration: [y/n] y [Enter]

................

Device is Going for Reboot....

Manually re-configure the optional Gigabit Ports from the web browser

Launch your web browser and enter the assigned IP Address and login to the switch.

Verify the Software Revision at the main menu when presented.

Browse to the Gigabit Ports submenu found under the Administration menu and configure

modules for each slot respectively. Then, click the update button.

To verify the configuration has been saved, allow the switch to reboot and log back in to the web

browser interface and compare the Logical View with the physical switch to confirm the settings

were saved correctly.

Note: 7014FX2 without optional Gigabit Ports installed shown above.

This completes the firmware upgrade process.

Table des matières

Autres manuels Ntron Changer

Ntron

Ntron 9000 Series Instructions d'installation et d'utilisation

Ntron

Ntron 7026 Series Instructions d'installation et d'utilisation

Ntron

Ntron 708TX Instructions d'installation et d'utilisation

Ntron

Ntron 600 Series Manuel utilisateur

Ntron

Ntron 509FX Manuel utilisateur

Ntron

Ntron 508TX-N Manuel utilisateur

Ntron

Ntron 524TX Manuel utilisateur

Ntron

Ntron 7012FX2 Series Instructions d'installation et d'utilisation

Ntron

Ntron 7010TX Series Instructions d'installation et d'utilisation

Ntron

Ntron 608MFX-ST Manuel

Ntron

Ntron 712FX4 Series Instructions d'installation et d'utilisation

Ntron

Ntron 105FX-POE Instructions d'installation et d'utilisation

Ntron

Ntron NT24k Manuel utilisateur

Ntron

Ntron 302MC-XX Manuel utilisateur

Ntron

Ntron 714FX6 Series Instructions d'installation et d'utilisation

Ntron

Ntron 300 Manuel utilisateur

Ntron

Ntron 100-POE-SPL Instructions d'installation et d'utilisation

Ntron

Ntron 604MFX-ST Manuel

Ntron

Ntron 105TX-SL Manuel utilisateur

Ntron

Ntron 710FX2 Series Instructions d'installation et d'utilisation

Ntron

Ntron ESERV-M12T Manuel utilisateur

Ntron

Ntron 7014TX Instructions d'installation et d'utilisation

Ntron

Ntron 100-POE4-MDR Instructions d'installation et d'utilisation

Ntron

Ntron 702-W Manuel du propriétaire

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur