Ntron 900 Manuel d'utilisation

900 Series

Industrial Ethernet

Switch

Installation

& User’s Guide

4/26/2007

Industrial Ethernet Switch Installation Guide

900B/900N

(3 Slot Enclosure and Backplane)

900B-FP

(Filler Panel for empty slots)

908TX

(Module)

902FX-SC

(Module)

902FX-ST

(Module)

902FXE-SC-YY

(Module)

902FXE-ST-YY

(Module)

904FX-SC

(Module)

904FX-ST

(Module)

904FXE-SC-YY

(Module)

904FXE-ST-YY

(Module)

Where: YY = -15, -40, or -80

4/26/2007

N-TRON Corp.

820 S. University Blvd., Suite 4E

Mobile, AL 36609

Corp. is prohibited, except as allowed under copyright laws.

Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos

or other designations mentioned herein are trademarks of their respective owners.

The information contained in this document is subject to change without notice. N-TRON Corp. makes no

warranty of any kind with regard to this material, including, but not limited to, the implied warranties of

merchantability or fitness for a particular purpose. In no event shall N-TRON Corp. be liable for any

incidental, special, indirect or consequential damages whatsoever included but not limited to lost profits

arising out of errors or omissions in this manual or the information contained herein.

Warning

Do not perform any services on the unit unless qualified to do so.

Do not substitute unauthorized parts or make unauthorized modifications to the unit.

Do not operate the unit with the top cover removed, as this could create a shock or fire hazard.

Do not block the air vents on the sides or the top of the unit.

Do not operate the equipment in the presence of flammable gasses or fumes. Operating electrical equipment

in such an environment constitutes a definite safety hazard.

4/26/2007

Safety Warnings

ELECTRICAL SAFETY

WARNING: Disconnect the power cable before removing the enclosure top.

WARNING: Do not operate the unit with the top cover removed.

WARNING: Do not work on equipment or cables during periods of lightning activity.

WARNING: Do not perform any services on the unit unless qualified to do so.

WARNING: Do not block the air vents.

WARNING: Observe proper DC Voltage polarity when installing power input cables. Reversing

voltage polarity can cause permanent damage to the unit and void the warranty.

LASER SAFETY (904FXE and 902FXE Only)

WARNING: CLASS 1 Laser Product. Do not stare into the Laser Beam.

4/26/2007

900 Series Hazardous Location Installation Requirements

1. WARNING: EXPLOSION HAZARD. DO NOT DISCONNECT UNIT WHILE CIRCUIT IS LIVE,

UNLESS KNOWN TO BE NON-HAZARDOUS.

2. AVERTISEMENT: RISQUE D’EXPLOSION. NEPAS DE’BRANCHER TANT QUE LE CIRCUIT

EST SOUS TENSION, A’MOINS QU’IL S’ A GISSE D’UN EMPLACEMENT NON DANGEREUX.

3. WARNING: Install only in accordance with Local & National Codes of Authorities Having Jurisdiction.

4. Power must be supplied by an isolating source, and a 3.3A max rated UL recognized fuse must be

installed immediately before the unit.

5. Class I, Div 2 installations require that all devices connected to this product must be UL listed for the area in

which it is installed.

6. Only UL listed wiring with temperature ratings greater than 90

C permitted for Class I, Div 2 installations

operating at temperatures up to 70

C ambient.

7. Limited Operating Voltage: 12-30V for Class I, Div 2 installations.

4/26/2007

900 Series Industrial Ethernet Switches

The 900 Series Modular Industrial Ethernet Switches support high speed layer 2 switching between ports.

The 900B and 900N enclosures contain a three slot backplane that supports up to three modules. The

908TX, 902FX and 904FX modules are the available modules. The N-TRON Corp. 900B is housed in a

ruggedized steel enclosure, and can withstand industrial temperatures, as well as extreme shock & vibration.

The 908TX is an 8 port module that is capable of auto negotiating 10/100 Mb and half/full duplex

communications. The N-TRON 908TX also supports MDIX auto sensing (for auto connector of straight

through or crossover cables) and provides 8 Category 5 compliant 10/100-BaseT connections for high

performance network design, and hub/repeater upgrades.

The 902FX is a two port 100Mb module that supports multimode fiber. ST and SC connectors are

available.

The 902FXE is a single mode (laser) version of the 902FX, and can support distances of up to 80km.

The 904FX and 904FXE are four port versions of the 902FX and 902FXE respectively.

Key Features

•Full IEEE 802.3 & 100BASE-FX Compliance

•Extended Environmental Specifications

•Support for Full/Half Duplex Operation

•LED Link/Activity Status Indication

•Auto Sensing Speed and Flow Control

•Auto MDIX (908TX only)

•Up to 4.8 Gb/s Maximum Throughput

•Industry Standard DIN-Rail Enclosure

4/26/2007

PACKAGE CONTENTS

Please make sure the Ethernet Switch package contains the following items:

1. 900 Series Ethernet Switch

2. Installed Modules

3. This Installation Guide

Contact your carrier if any items are damaged.

INSTALLATION

Read the following warning before beginning the installation:

WARNING

The 902FXE and 904FXE unit contain a class 1 laser. Do not stare into the laser beam (fiber optic

connector) when installing or operating the product.

Never install or work on electrical equipment or cabling during periods of lightning activity.

Disconnect the power cable before removing the enclosure top.

Do not operate the unit with the top cover removed

UNPACKING

Remove all the equipment from the packaging, and store the packaging in a safe place.

File any damage claims with the carrier.

4/26/2007

902FX/FXE & 904FX /FXE HALF DUPLEX SETUP

All 900 series fiber modules are factory configured for full duplex operation. The setting is controlled

by jumper JP1 on the backplane.

Note: Most 100Mbit fiber systems will be compatible with this Full Duplex setting. If Half Duplex

operation is desired, then follow these steps using proper wrist strap grounding techniques:

1. Remove the power & power plugs from the unit.

2. Loosen all thumbscrews & remove all modules.

3. Remove the six screws holding the backplane

4. Remove the backplane.

5. Move the jumper JP1 from position 1-2 to 3-4

6. Re-install the backplane & modules & power plugs.

902/904 Note:

Rev. C & D boards are hard wired for Port1 = HDPLX,

Rev. B & E boards are hard wired for Port1 = FDPLX.

JP1

4/26/2007

DIN-Rail Mounting

Install the unit in a standard DIN-Rail. Recess the unit to allow at least 5” of horizontal clearance for

fiber optic cable bend radius (2” for TX models). Note: This unit may be mounted horizontally or

vertically.

To install the unit to 35mm industrial DIN-Rail - Place the top edge of the included mounting bracket on

the back of the unit against the top flange of the DIN-Rail at a 15° angle. Rotate the bottom of the unit to

the back (away from you) until it snaps into place.

To remove the unit from the 35 mm industrial DIN-Rails - Apply downward force to the unit until it

disengages from the bottom of the unit from the DIN-Rail. Then, rotate the unit approximately 15°

upward and towards you to completely remove it.

Optional Mounting

The 900 Series Ethernet switches were designed to be mounted on industry standard 35mm DIN-Rail.

However, DIN-Rail mounting may not be suitable for all applications. We offer two alternative

mounting solutions.

Our 900 Panel Mount Assembly (P/N: 900-PM) may be used to securely mount the 900 Series products

to a panel or other flat surface.

Our Rack Mount Assembly (P/N: 900-RM) may be used to mount our products to standard 19" racks.

4/26/2007

MODULE CONFIGURATION SETTINGS

In order for the 900 Series modules to communicate properly the chassis must be populated with modules from the top

slot down as shown below. In addition, JP1 and JP2 jumpers (located on top side of all modules) must be configured as

indicated below.

Note: The power source must be disconnected from the 900B chassis prior to removing and inserting modules. This

unit is not hot swappable.

One Slot Configuration - When installing a single 902FX, 904FX, or 908TX module in

the top slot of the 900B chassis… Configure the module as follows:

JP1: pins 1 & 2 shorted

JP2: pins 1 & 2 shorted

Two Slot Configuration - When installing two 902FX, 904FX, and/or 908TX modules

in the top two slots of the 900B chassis… Configure both modules as follows:

JP1: pins 1 & 2 shorted

JP2: pins 3 & 4 shorted

Three Slot Configuration - When installing three 902FX, 904FX, and/or 908TX

modules in all three slots of the 900B chassis… Configure all modules as follows:

JP1: pins 3 & 4 shorted

JP2: pins 3 & 4 shorted

908TX Module - At power cycle, all LED’s flash on for approximately two seconds, and

then return to proper state. Green LED will light when Power is connected.

902FX & 904FX Modules - At power cycle, only the LED’s on the first port flash on to

indicate the reset condition, and then return to their proper state. All other reports remain

off during reset. This is normal behavior. Green LED will light when Power is

connected.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ntron Changer

Ntron

Ntron 100 Series Instructions d'installation et d'utilisation

Ntron

Ntron 604MFX-ST Manuel

Ntron

Ntron 524TX Manuel utilisateur

Ntron

Ntron 108M12 Manuel utilisateur

Ntron

Ntron NTSFP-LX-40 Instructions d'installation et d'utilisation

Ntron

Ntron 708TX Instructions d'installation et d'utilisation

Ntron

Ntron 100-POE4-MDR Instructions d'installation et d'utilisation

Ntron

Ntron 702-W Manuel du propriétaire

Ntron

Ntron 711FX3 Series Instructions d'installation et d'utilisation

Ntron

Ntron 608MFX-ST Manuel utilisateur

Ntron

Ntron 509FX Manuel utilisateur

Ntron

Ntron ESERV-M12T Manuel utilisateur

Ntron

Ntron 500 Series Manuel utilisateur

Ntron

Ntron 405FX-SC Manuel utilisateur

Ntron

Ntron 508TX-N Manuel utilisateur

Ntron

Ntron 7012FX2 Series Instructions d'installation et d'utilisation

Ntron

Ntron 608MFX-ST Manuel utilisateur

Ntron

Ntron 7010TX Series Instructions d'installation et d'utilisation

Ntron

Ntron 708FX2 Manuel utilisateur

Ntron

Ntron 100-POE-SPL Instructions d'installation et d'utilisation

Ntron

Ntron 508TX Manuel utilisateur

Ntron

Ntron 105FX-POE Instructions d'installation et d'utilisation

Ntron

Ntron 600 Series Manuel utilisateur

Ntron

Ntron 7014 Series Guide de démarrage rapide

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur