NovaStar MCTRL 4K Manuel utilisateur
XI'AN NOVASTAR TECH CO.,LTD.
Statement
Welcome to use the product from Xi’an NovaStar Tech Co., Ltd. (hereinafter
referred to as “Novastar”). It is our great pleasure to offer this manual to help
you understand and use the product. We have striven for precision and reliability
during the compilation of this manual, and the contents of this manual are subject
to change at any time without further notice. If you have any problem during
use or you have any suggestion, please feel free to contact us according to the
contact information provided in this manual. We will do our utmost to satisfy your
needs. We would like to express our sincere appreciation to your suggestions and
make assessment for adoption as soon as possible.
Copyright
All the intellectual property rights involved in this document belong to NovaStar.
No part of this document may be reproduced or extracted in any form or by any
means without prior written consent of NovaStar. All rights are reserved.
Trademark
is the registered trademark of NovaStar.
Safety Statement
To avoid potential hazards, please use this controller according to regulations.
Power outlet should be installed near the controller and easy to reach. In the
event of breakdowns, non-professionals are not allowed to disassemble the
controller for maintenance. Please contact the after-sales department of NovaStar
timely.
High voltage danger: The operating voltage range of this product is
100-240V AC.
Grounding: This product is grounded through the grounding cord of
power supply. Please keep the grounding conductor well grounded.
Electromagnetic interference: Keep this product far away from
magnets, motors and transformers.
Moisture proof: Keep this product in a dry and clean environment. In
case of liquid immersion, please pull the power plug out immediately.
Keep this product away from flammable and explosive substances.
Prevent liquids or metal fragments from dropping into the product in
order to avoid safety accidents.
XI'AN NOVASTAR TECH CO.,LTD.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .This equipment should be installed and operated with
minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
XI'AN NOVASTAR TECH CO.,LTD.
Table of Contents
1 Appearance...................................................................................................... 1
Front Panel .........................................................................................................................1
Rear Panel ...........................................................................................................................1
2 Signal Connection........................................................................................... 3
3 Dimensions...................................................................................................... 4
4 Operating Motion Instruction....................................................................... 4
5 Main Interface................................................................................................. 5
6 Menu Operation.............................................................................................. 6
Step 1 Input Mode........................................................................................................... 6
Step 2 Input Resolution.................................................................................................. 6
Step 3 Quick Config.........................................................................................................7
Step 4 Brightness Adjustment ..................................................................................... 8
Screen Settings .................................................................................................................9
Display Control .................................................................................................................9
Advanced Settings.........................................................................................................10
Communication Settings .............................................................................................12
Language ..........................................................................................................................12
7 Technical Specifications ............................................................................... 13
8 FAQs and Precautions .................................................................................. 14
XI'AN NOVASTAR TECH CO.,LTD.
-1-
MCTRL4K User‘s Manual
1 Appearance
Front Panel
① : Power button; Press the button for startup. After startup, press and hold the
button for 4~5 seconds to power off.
② : USB interface for connecting USB drives only(unable to connect computers).
③ : Operation screen
④：Knob; Pressing the knob indicates Enter or OK, rotating the knob allows us to
select or adjust.
⑤：BACK; Back to the previous menu.
Rear Panel
XI'AN NOVASTAR TECH CO.,LTD.
MCTRL4K User‘s Manual
-2-
Inputs
DP 1.2 DP 1.2 interface
HDMI 2.0 HDMI 2.0 interface
DUAL DVI-D1/D2 Dual-link DVI interface
Outputs
1~16 16-channel Neutrik Gigabit Ethernet outputs
OPT1~4
4-channel optical fiber outputs
OPT1 is corresponding to Ethernet port 1~8.
OPT2 is corresponding to Ethernet port 9~16.
OPT3 is the backup of OPT1. OPT4 is the backup of
OPT2.
Control
ETHERNET Control interface
USB IN: cascade input or connecting PC;
OUT: cascading next unit.
GenLock
IN
Genlock synchronous signal, making sure the picture
on LED display is in sync with external Genlock
source.
Genlock type: Blackburst
LOOP Genlock loop output
Power
AC 100-240V ～ 50/60HZ AC power interface
Note: Type A(flat) USB interface is not allowed to be connected to control computer
directly.
XI'AN NOVASTAR TECH CO.,LTD.
-3-
MCTRL4K User‘s Manual
2 Signal Connection
Please refer to the previous chapter of interface intrduction and the figure
below to connect requied hardwares.(Note: Please disconnect the power of the
equipment while connecting signal.)
If it is required to control multiple MCTRL4K units, please connect them according
to the figure below.
XI'AN NOVASTAR TECH CO.,LTD.
MCTRL4K User‘s Manual
-4-
3 Dimensions
(mm)
4 Operating Motion Instruction
Knob:
While in main interface, press the knob to enter menu interface;
While in menu interface, rotate the knob to select menus and press the
knob to select current menu or enter submenus;
Select a menu with parameters and rotate the knob to adjust the
parameters. Please remember to press the knob again for confirmation after
adjustment.
BACK: A return button to exit from current menu or operation.
Lock /Unlock buttons: Press and hold the knob and ESC key simultaneously.
XI'AN NOVASTAR TECH CO.,LTD.
-5-
MCTRL4K User‘s Manual
5 Main Interface
Switch on the controller and the main interface of its screen is shown as below:
A: Input state of signal sources. Blue indicates it has signal while gray indicates no
signal;
B: Current input source and its resolution, frame rate. For example, the information
of two DVI sources will be displayed alternately here when dual-link DVI is selected
as input.
C: Width, height and frame rate of the LED display being configured;
D: Status, the meanings of each status icon are introduced as follows:
Supply voltage of mainboard core
Temperature inside the controller
Brightness of LED display
/DVI1 and DVI2 are not synchronous/synchronous
/ / Control interface, not connected/connected to USB port/
connected to Ethernet port
/Screen unlocked/locked
E: Connection status of Ethernet ports. Blue indicates that the connection is available
and the port works as master control while gray indicates the port is not connected
or the connection is unavailable. Mark on the upper left corner of the icon indicates
that the connection is available and the port is in redundancy state.
F: Connection status of optical fiber ports. Blue indicates that the connection is
available and the fiber port works as master control while gray indicates the port is
not connected or the connection is unavailable. Mark on the upper left corner of the
icon indicates that the connection is available and the port is in redundancy state.
XI'AN NOVASTAR TECH CO.,LTD.
MCTRL4K User‘s Manual
-6-
6 Menu Operation
MCTRL4K is powerful and easy-to-use. In general, users can start a LED display and
operate it normally through first four steps. Users also can set other options in the
menu selectively for better display effects.
Step 1 Input Mode
MCTRL 4K supports two input modes: mosaic and muli-card.
Main
Brightness
Input Settings
Screen Settings
Display Control
Advanced Settings
Communication Settings
Language
Input Settings
Input Mode
Input Resolution
Input Mode
DVI Mode Mosaic
Input Source
Mosaic Mode
In mosaic mode, Auto, DP, HDMI or DVI×2(Mosaic direction is optional.) can be
selected as video input source.
In multi-card mode, MCTRL4K is used as two independent controllers and the
loading capacity of each is up to 3840×2160@30Hz. Now both DVI 1 and DVI 2
inputs are available and can be displayed on LED display simultaneously. But only
one of them can be set at the same time, namely, the currently selected video
input source.
In multi-card mode, the corresponding outputs of DVI 1 are Ethernet port 1~8 or
OPT1 while the corresponding outputs of DVI 2 are Ethernet port 9~16 or OPT2.
Tip: When input source is set to "Auto", the controller will automatically detect input
source depending on the priority order of DP>HDMI>DVI.
Step 2 Input Resolution
Users are capable of setting the resolution of each input source as required.
Input Settings
Input Mode
Input Resolution
Input Resolution
Preset
Custom
Input resolution is able to be set through the following two methods:
I: Preset
XI'AN NOVASTAR TECH CO.,LTD.
Table des matières
Autres manuels NovaStar Contrôleurs
NovaStar
NovaStar VX4 Manuel utilisateur
NovaStar
NovaStar MCTRL4K Manuel utilisateur
NovaStar
NovaStar CX40 Pro Manuel utilisateur
NovaStar
NovaStar VX6s Manuel utilisateur
NovaStar
NovaStar MCTRL660 PRO Manuel utilisateur
NovaStar
NovaStar MCTRL660 PRO Manuel utilisateur
NovaStar
NovaStar VX4S-N Manuel utilisateur
NovaStar
NovaStar VX400 Manuel utilisateur
NovaStar
NovaStar MCTRL4K Manuel utilisateur
NovaStar
NovaStar C1 Manuel utilisateur
NovaStar
NovaStar MCTRL4K Manuel utilisateur
NovaStar
NovaStar MCTRL660 PRO Manuel utilisateur
NovaStar
NovaStar VX400s Manuel utilisateur
NovaStar
NovaStar MX6000 Pro Manuel utilisateur
NovaStar
NovaStar MCTRL R5 Manuel utilisateur
NovaStar
NovaStar CX80 Pro Manuel utilisateur
NovaStar
NovaStar Thunderview S1 Manuel utilisateur
NovaStar
NovaStar MX Series Manuel utilisateur
NovaStar
NovaStar MCTRL660 PRO Manuel utilisateur
NovaStar
NovaStar NovaPro UHD Jr Manuel utilisateur
