NovaStar MCTRL660 PRO Manuel utilisateur

Xi’an NovaStar Tech Co., LTD

M3 Controller MCTRL660 User Manual

Document number: NOVA2013-MCTRL660-HB-01

Version: V1.2.0

XI'AN NOVASTAR TECH CO., LTD

www.novastar-led.com

Phone: NovaStar (Xian) +86 29 8450 7048 NovaStar (Shenzhen) +86 755 3359 2491

Website: www.novastar-led.com 2

1Overview

MCTRL660, NovaStar's latest independent master control, is mainly applied to screen leasing. It

adopts an innovative architecture to implement smart configuration; the screen debugging can

be completed within 30 seconds. It adopts the Nova G4 engine; the screen is stable and flicker

free without scanning lines; the images are exquisite and have a good sense of depth. It supports

Nova's new-generation point-by-point correction technology; the correction is fast and efficient.

It can implement white balance calibration and color gamut mapping based on different features

of LEDs used by screens to ensure reproduction of true colors. It is the only control system

supporting the input of 12-bit high-definition multimedia interface (HDMI) and high-bandwidth

digital content protection (HDCP) in China. It supports screen configuration at any time without a

computer. It supports manual adjustment of the screen brightness, which is convenient and

efficient. These features satisfy the special needs of screen leasing to the maximum extent.

XI'AN NOVASTAR TECH CO., LTD

www.novastar-led.com

Phone: NovaStar (Xian) +86 29 8450 7048 NovaStar (Shenzhen) +86 755 3359 2491

Website: www.novastar-led.com 3

2Product Appearance and Interfaces

Operation screen:

A. Indicate access of a video source on the

HDMI. It blinks in the case of no video

source input.

B. Indicate that the machine is in the master

mode.

C. Indicate that the resolution is 1920 pixels x

1080 pixels and that the frame frequency

is 60 Hz.

D. Indicate that the current brightness of the

screen is 50%.

E. Indicate that network interface 2 has

loads.

PWR: Indicate the power indicator.

RUN: Indicate equipment running indicator

1. It blinks quickly when no video source is

available and blinks normally when a video

source is available. when the redundancy

works, the indicator fades gradually.

STA: Indicate equipment running indicator 2.

It is steady on when the equipment runs

normally and blinks during authorization.

Button: Press the button to enter the option

and rotate the button to conduct selection or

adjustment.

: exit from the current operation or

option.

XI'AN NOVASTAR TECH CO., LTD

www.novastar-led.com

Phone: NovaStar (Xian) +86 29 8450 7048 NovaStar (Shenzhen) +86 755 3359 2491

Website: www.novastar-led.com 4

3Operation Instructions

All operations on the MCTRL660 are implemented through the button and return key.

Button: Press the button to enter a menu. After entry into a menu, rotate the button to adjust the value or

select a submenu.

Return key: Press the return key to exit from the current menu or operation.

DVI OUT : Indicate the digital visual interface

(DVI) output interface.

DVI IN : Indicate the DVI input interface.

OUT1-OUT2 : Indicates output by four network

interfaces.

HDMI OUT: Indicate the HDMI output interface.

HDMI IN : Indicate the HDMI input interface.

TO PC : Indicate the interface for connecting the

computer.

AUDIO : Indicate the audio input interface.

UART IN : Indicate the cascading input interface of

serial ports.

UART OUT: Indicate the cascading output

interface of serial ports.

AC-100-240V-50/60HZ: Indicate the AC power

interface.

XI'AN NOVASTAR TECH CO., LTD

www.novastar-led.com

Phone: NovaStar (Xian) +86 29 8450 7048 NovaStar (Shenzhen) +86 755 3359 2491

Website: www.novastar-led.com 5

4Procedure

4.1 Step 1: Connecting the Hardware

Connect the hardware by referring to the interface description in Chapter 2.

4.2 Step 2: Screen Configuration

1) The screen being power-on, if the cabinet is in normal display, enter into step 2); if the cabinet is

in abnormal display, first load the cabinet file, and fix it to the receiving card; see detailed

operation in 4.5 Advanced Setting 。

2) Return to the “Screen Configuration”submenu. Rotate the button to switch to submenus of

other options respectively to perform configurations, as shown in the following figures:

a) Set Cabinet Row Num and Cabinet Col Num according to the actual situation of the

screen.

b) Set Cabinet Out1 Num. The device has some limitations on the cabinet quantity of

XI'AN NOVASTAR TECH CO., LTD

www.novastar-led.com

Phone: NovaStar (Xian) +86 29 8450 7048 NovaStar (Shenzhen) +86 755 3359 2491

Website: www.novastar-led.com 6

network interfaces. For details, see precautions for screen setting i).

c) Set the alignment of the screen. Pay attention to precautions for screen setting iii), iv) and v)

below.

d) Set the resolution of the video source.

Precautions for screen setting:

i. If the number of network interfaces with

loads is n (n≤4), the first n-1 network

interfaces must have the same number of

cabinets, which must also be an integral

multiple of the number of cabinet rows or

columns and be greater than or equal to

the number of cabinets for the nth

network interface.

Example:

For example, if network interface 1, network interface

2, network interface 3 have loads, network interface

1 and network interface 2 must have the same

number of cabinets, which must also be an integral

multiple of the number of cabinet rows or columns.

Therefore, you need only to set cabinet out1 num

according to the actual situation when setting the

screen. The number of receiving cards for network

interface 3 must be smaller than or equal to cabinet

out1 num

ii. In the case of special-shaped cabinets, different cabinet sizes and special-shaped screen, the

NovaLCT-Mars software is required to be connected to configure the screen.

iii. During connection setting, you can rotate the button to see the effects of different connections on

the screen in real time. If you are satisfied with the connection, you must press the button to save

the setting. You can press the return key to exit from the current operation.

XI'AN NOVASTAR TECH CO., LTD

www.novastar-led.com

Phone: NovaStar (Xian) +86 29 8450 7048 NovaStar (Shenzhen) +86 755 3359 2491

Website: www.novastar-led.com 7

iv. During connection setting, you must ensure that the connection of each network interface is

downward in the same direction.

v. During connection setting, you must ensure that network interface 1 is the start position of the

whole connection.

4.3 Step 3: Adjusting the Brightness of the Screen

Return to the main menu interface. Press the button to select the corresponding value. You can rotate the

button to adjust the brightness at this time.

4.4 Setp4 Input Resolution

Namely the resolution of home page display of interface, which must be in coincidence with output

resolution of video source.

XI'AN NOVASTAR TECH CO., LTD

www.novastar-led.com

Phone: NovaStar (Xian) +86 29 8450 7048 NovaStar (Shenzhen) +86 755 3359 2491

Website: www.novastar-led.com 8

After step 4 is completed, you can turn on the screen and normally use the screen. To achieve better

display effects, you can continue to set other parameters.

You can set other parameters by referring to Section 4.5 "Advanced Setting."

4.5 Advanced Setting

4.5.1 load Cabinet Files

After the screen is powered on, if the cabinet fails to display normally, you must load cabinet files first. The

cabinet files must be sent to the MCTRL660 through the NovaLCT-Mars beforehand. The following

figures show the procedure:

XI'AN NOVASTAR TECH CO., LTD

www.novastar-led.com

Phone: NovaStar (Xian) +86 29 8450 7048 NovaStar (Shenzhen) +86 755 3359 2491

Website: www.novastar-led.com 9

Select the corresponding COM

port of the MCTRL660.

XI'AN NOVASTAR TECH CO., LTD

www.novastar-led.com

Phone: NovaStar (Xian) +86 29 8450 7048 NovaStar (Shenzhen) +86 755 3359 2491

Website: www.novastar-led.com 10

XI'AN NOVASTAR TECH CO., LTD

Autres manuels pour MCTRL660 PRO

Table des matières

Autres manuels NovaStar Contrôleurs

NovaStar

NovaStar VX6s Manuel utilisateur

NovaStar

NovaStar MCTRL4K Manuel utilisateur

NovaStar

NovaStar C1 Manuel utilisateur

NovaStar

NovaStar VX600 Manuel utilisateur

NovaStar

NovaStar MCTRL4K Manuel utilisateur

NovaStar

NovaStar VX4 Manuel utilisateur

NovaStar

NovaStar MCTRL4K Manuel utilisateur

NovaStar

NovaStar NovaPro UHD Manuel utilisateur

NovaStar

NovaStar VX600 Manuel utilisateur

NovaStar

NovaStar MBOX600 Manuel utilisateur

NovaStar

NovaStar MCTRL660 PRO Manuel utilisateur

NovaStar

NovaStar VX6s Manuel utilisateur

NovaStar

NovaStar C1 Manuel utilisateur

NovaStar

NovaStar MX40 Pro Manuel utilisateur

NovaStar

NovaStar MCTRL660 PRO Manuel utilisateur

NovaStar

NovaStar VX4 Manuel utilisateur

NovaStar

NovaStar nova3D HD Manuel utilisateur

NovaStar

NovaStar MBOX600 Manuel utilisateur

NovaStar

NovaStar MBOX600 Manuel utilisateur

NovaStar

NovaStar MCTRL 4K Manuel utilisateur

NovaStar

NovaStar CX80 Pro Manuel utilisateur

NovaStar

NovaStar VX400s Manuel utilisateur

NovaStar

NovaStar VX4 Manuel utilisateur

NovaStar

NovaStar MX Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur