Nortel 8300 Series Mode d’emploi

Nortel Networks Ethernet Routing Switch 8300

Installation and Commissioning

— Quick Start

NN46200-100 (322800-A)

Document status: Standard

Document version: 02.01

Document date: 6 September 2006

The information in this document is subject to change without notice. The statements, conﬁgurations, technical

data, and recommendations in this document are believed to be accurate and reliable, but are presented without

express or implied warranty. Users must take full responsibility for their applications of any products speciﬁed in this

document. The information in this document is proprietary to Nortel Networks.

Trademarks

*Nortel, Nortel Networks, the Nortel Logo, and the Globemark are trademarks of Nortel Networks.

All other trademarks and registered trademarks are the property of their respective owners.

Contents

Introduction 5

Installing the chassis 9

Conﬁguration 19

Index 23

Figures

Figure Removing a module or power supply ﬁller panel for 8306 and 8310

chassis 10

Figure Attach rack-mounting bracket to the 8306 chassis 11

Figure Attach rack-mounting bracket to the 8310 chassis 11

Figure Installing the 8306 chassis in an equipment rack 12

Figure Installing the 8310 chassis in an equipment rack 12

Figure Installing the cable guides: 8306 chassis 13

Figure Installing the cable guides: 8310 chassis 13

Figure Installing a module: 8306 and 8310 chassis 14

Tables

Table Chassis shipping accessories checklist 9

Table Setup utility prompt descriptions 20

Nortel Networks Ethernet Routing Switch 8300

Installation and Commissioning — Quick Start

NN46200-100 02.01 Standard

3.0 6 September 2006

4Contents

Nortel Networks Ethernet Routing Switch 8300

Installation and Commissioning — Quick Start

NN46200-100 02.01 Standard

3.0 6 September 2006

Introduction

This Quick Start Guide provides basic instruction on how to install the

hardware and perform basic conﬁguration of the Ethernet Routing Switch

8300 Series chassis.

See the Read Me First for the Ethernet Routing Switch 8310 and 8306

Chassis (318192-C) for important information before you begin.

Note: The Read Me First for the Ethernet Routing Switch 8310 and

8306 Chassis (318192-C) contains the regulatory and safety information.

Audience The Quick Start Guide is intended for experienced installers.

How to get help

This section explains how to get help for Nortel products and services.

Getting help from the Nortel web site

The best way to get technical support for Nortel products is from the Nortel

Technical Support web site:

www.nortel.com/support

This site provides quick access to software, documentation, bulletins, and

tools to address issues with Nortel products. From this site, you can:

•download software, documentation, and product bulletins

•search the Technical Support web site and the Nortel Knowledge Base

for answers to technical issues

•sign up for automatic notiﬁcation of new software and documentation

for Nortel equipment

•open and manage technical support cases

Nortel Networks Ethernet Routing Switch 8300

Installation and Commissioning — Quick Start

NN46200-100 02.01 Standard

3.0 6 September 2006

6Introduction

Getting help over the phone from a Nortel Solutions Center

If you do not ﬁnd the information you require on the Nortel Technical Support

web site, and you have a Nortel support contract, you can also get help over

the phone from a Nortel Solutions Center.

In North America, call 1-800-4NORTEL (1-800-466-7835).

Outside North America, go to the following web site to obtain the phone

number for your region:

www.nortel.com/callus

Getting help from a specialist by using an Express Routing Code

To access some Nortel Technical Solutions Centers, you can usean Express

Routing Code (ERC) to quickly route your call to a specialist in your Nortel

product or service. To locate the ERC for your product or service, go to:

www.nortel.com/erc

Getting help through a Nortel distributor or reseller

If you purchased a service contract for your Nortel product from a distributor

or authorized reseller, contact the technical support staff for that distributor

or reseller.

Precautions For your safety, review the following personal safety warnings before

working with the Ethernet Routing Switch 8300 Series.

DANGER

Risk of injury by electric shock

Use only power cords that have a grounding path. Without a

proper ground, a person who touches the switch is in danger of

receiving an electrical shock. Lack of a grounding path to the

switch may result in excessive emissions.

WARNING

Risk of injury by fan blades

When removing the fan module, do not put your hands into the

opening because there are spinning fan blades in the adjacent fan

modules. There is also a risk of electric shock from the electrical

connector at the rear of the slot.

Nortel Networks Ethernet Routing Switch 8300

Installation and Commissioning — Quick Start

NN46200-100 02.01 Standard

3.0 6 September 2006

Precautions 7

WARNING

Risk of eye injury by laser

Fiber optic equipment can emit laser or infrared light that can injure

eyes. Never look into an optical ﬁber or connector port. Always

assume that ﬁber optic cables are connected to a light source.

CAUTION

If you are not installing a module in the slot, be sure to keep the

metal cover plate in place over the slot. Removing the cover plate

impedes airﬂow and proper cooling of the unit.

Protecting modules

Follow these general practices to prevent equipment damage when working

on the Ethernet Routing Switch 8300 Series:

•Always wear an antistatic wrist strap connected to an Electrostatic

discharge (ESD) grounding jack when handling modules.

•Always set modules on appropriate antistatic material.

•Handle modules by the faceplate. Do not touch pins or electrical

connections.

•Do not leave slots open. All slots must be ﬁlled with modules or, if empty,

covered with slot covers to maintain safety compliance, proper cooling,

and EMI containment in the shelf.

•Ensure that your environment meets the necessary requirements for

temperature, humidity, and cleanliness.

•Do not overtighten thumb screws or lug nuts. Tighten until snug plus a

quarter turn. If you use a power tool to tighten screws, use a low torque

setting (2-3 in/lbs).

For additional information on installing modules, see Nortel Ethernet

Routing Switch 8300 Installation — Modules (NN46200-305).

Protecting cables and connectors

•Support cables to prevent any stress on the connectors. If you have

a high cable density conﬁguration, you need to install additional

cable-management equipment.

•Do not exceed the bend radius recommended for the type of cable

installed.

•Do not exceed the bend radius recommended for ﬁber optic cable. The

acceptable bend radius for ﬁber optic cable is ten times its diameter, or

2.5-5 cm (1-2 in.). Anything less than the recommendation can cause

Nortel Networks Ethernet Routing Switch 8300

Installation and Commissioning — Quick Start

NN46200-100 02.01 Standard

3.0 6 September 2006

8Introduction

a loss of integrity of data transmission. Loss of integrity because of

incorrect bend radius is difﬁcult to diagnose.

•Fiber optic cables and connectors require special care.

— Protect connectors with rubber safety plugs when cables are not

inserted.

— When installing or replacing cables, follow appropriate ﬁber-cleaning

procedures.

Electrostatic discharge

Electrostatic discharge (ESD) is the transfer of charge between bodies at

different electrical potentials. ESD can change the electrical characteristics

of a semiconductor device and degrade or destroy it. ESD can also

disrupt the normal operation of an electronic system by causing equipment

malfunction or failure.

To dissipate or neutralize electrostatic charges, use proper grounding and

use conductive or dissipative materials.

Use an ESD wrist strap. Any charge in your body will go to ground rather

than transfer to hardware modules.

Proper antistatic packaging effectively shields the product from charge and

reduces the generation of charge caused by movement of the product

within the container.

Nortel Networks Ethernet Routing Switch 8300

Installation and Commissioning — Quick Start

NN46200-100 02.01 Standard

3.0 6 September 2006

Installing the chassis

Unpacking

Step Action

1Remove the shipping container.

2Place the chassis on antistatic material.

3Check all items for damage.

4Use the following chassis shipping accessories checklist to verify the

contents of the shipping container.

—End—

If you ﬁnd any damage, contact your Nortel sales representative.

Chassis shipping accessories checklist

Check Accessory Use To

Bracket kit containing: two

rack-mounting brackets and

Phillips-head screws (8-32 X 1/4 -

quantity 14 for 8306; quantity 24 for

8310)

Support the chassis in an equipment

rack

Screw package (10-32 X 3/4 -

quantity 10 for 8306; quantity 14 for

8310)

Mount the chassis in an equipment

rack

Side cable-management bracket(s):

two brackets for the 8310 chassis and

one bracket for the 8306 chassis

Manage network interface cables

Rubber footpads (quantity 4) Keep the chassis from slipping when

mounting it on a flat surface

Nortel Networks Ethernet Routing Switch 8300

Installation and Commissioning — Quick Start

NN46200-100 02.01 Standard

3.0 6 September 2006

10 Installing the chassis

Check Accessory Use To

Console cable with built-in adapter Connect an optional management

console to the chassis. Each end of

the cable has a DB9 connector.

Read Me First for the Ethernet

Routing Switch 8310 and 8306

Chassis (318192-C)

Read the regulatory and safety

information for the Ethernet Routing

Switch 8300.

For additional information on installing the 8310 and 8306 chassis, see

Installing and Maintaining the Ethernet Routing Switch 8306 and 8310

Chassis (316795-C) or Nortel Ethernet Routing Switch 8300 Installation —

Chassis Installation and Maintenance (NN46200-304).

Removing a module or power supply ﬁller panel

Nortel ships the 8300 series chassis with a ﬁller panel covering each empty

module slot. On an 8306 and 8310 chassis, the ﬁller panel covers an empty

module slot. Remove any ﬁller panels prior to installing the chassis to make

it lighter to install.

To remove a module or power supply ﬁller panel:

Step Action

1Using a Phillips screwdriver, loosen the 2 screws that fasten the

ﬁller panel to the chassis.

2Pull the panel away from the slot.

"Removing a module or power supply ﬁller panel for 8306 and 8310

chassis" (page 10) shows the location of the ﬁller cover for the 8306

and 8310 chassis.

Removing a module or power supply ﬁller panel for 8306 and 8310

chassis

—End—

Nortel Networks Ethernet Routing Switch 8300

Installation and Commissioning — Quick Start

NN46200-100 02.01 Standard

3.0 6 September 2006

Autres manuels pour 8300 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Nortel Changer

Nortel

Nortel Passport 1100 Mode d’emploi

Nortel

Nortel Passport 8306 Manuel utilisateur

Nortel

Nortel 4500 FIPS Manuel utilisateur

Nortel

Nortel Application Switch 2424-SSL Guide de référence

Nortel

Nortel 8005DC Manuel utilisateur

Nortel

Nortel 70 Series Manuel d'installation et d'exploitation

Nortel

Nortel 325 series Manuel utilisateur

Nortel

Nortel Contivity Extranet Switch 2500 Manuel utilisateur

Nortel

Nortel Passport 8003 Manuel utilisateur

Nortel

Nortel BayStack 420-24T Manuel utilisateur

Nortel

Nortel 3510-24T Manuel utilisateur

Nortel

Nortel BayStack 460 Switch Manuel de programmation

Nortel

Nortel BayStack 380-24T Manuel utilisateur

Nortel

Nortel BayStack 5510-24T Manuel utilisateur

Nortel

Nortel BayStack 325-24T Manuel utilisateur

Nortel

Nortel DMS-100 Series Instructions d'utilisation et d'entretien

Nortel

Nortel Passport 4400 Series Manuel de référence

Nortel

Nortel 4524GT Guide rapide

Nortel

Nortel 425-24T Manuel utilisateur

Nortel

Nortel Passport 2430 Manuel utilisateur

Nortel

Nortel 5500 series Manuel utilisateur

Nortel

Nortel Passport 241-5101-200 Manuel utilisateur

Nortel

Nortel 425-48T Manuel utilisateur

Nortel

Nortel BayStack 380 Mode d’emploi

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur