Nortel SONET AccessNode 800A Series Manuel utilisateur

P0887761 323-3001-210

SONET Products

AccessNode

Series 800A Outside Plant Cabinet

Installation

Issue 1.0 February 1999

AccessNode Series 800A Outside Plant Cabinet Installation 323-3001-210 Issue 1.0

SONET Products

AccessNode

Series 800A Outside Plant Cabinet Installation



Printed in Canada

All information contained in this document is subject to change without notice. Northern Telecom reserves the right to make

changestoequipmentdesignorprogramcomponents,asprogressinengineering,manufacturingmethods,orothercircumstances

may warrant.

DMS-100, ACCESSNODE, NORTEL, and NORTEL NETWORKS are trademarks of Northern Telecom.

Document number: 323-3001-210

Document release: Issue 1.0

Date: February 1999

AccessNode Series 800A Outside Plant Cabinet Installation 323-3001-210 Issue 1.0

iii

Publication history

February 1999

Standard AN16 release of the document, Issue 1.0. Changes include the

following:

• changed voltage settings for 6v Eag;e-Picher batteries in Chapter 10

June 1998

Release-independent Standard 01.01 release of the document. For this release,

the following information has been changed or added:

• graphics and procedures for cabinet lifting failure

• procedure for adjusting LVD potentiometer

September 1997

AN14 Standard release of the document. For this release, the following

information has been added:

• procedure for installing 6V batteries added to Chapter 9

• procedure for installing 12V batteries updated in Chapter 9

July 1996

AN12 Standard 01.01 release of the document.

November 1995

AN11 Standard 02.01 release of the document.

April 1995

Standard AN10 release of the document.

December 1994

Standard AN08 release of the document.

November 1994

Reissue of AN07 standard.

April 1994

Standard AN07 release of the document.

Publication history

AccessNode 323-3001-210 Issue 1.0

May 1993

Standard FWP06 release of the document.

AccessNode Series 800A Outside Plant Cabinet Installation 323-3001-210 Issue 1.0

Contents

About this document xi

Scope xi

What this document contains xi

How to use this document xii

References in this document xii

Abbreviations for the colors of conductor jackets in cables xiii

Installing the pad 1-1

How to use this chapter 1-1

Chapter task list 1-1

Site selection and preparation 1-2

Acoustical noise 1-2

Pad preparation 1-2

Pad applications 1-3

Pad drawings 1-3

Pad installation 1-4

Anchor plate kits 1-4

Cable entry 1-4

Procedure 1-1 Preparing the poured-in-place cabinet mounting pad 1-8

Procedure 1-2 Pouring the concrete 1-23

Installing the cabinet 2-1

How to use this chapter 2-1

Chapter task list 2-1

Prerequisites for installation 2-2

Mounting the cabinet 2-3

Anchor plate kits 2-3

Securing the cabinet to the pad 2-3

Cable entry 2-3

Termination compartment 2-3

AC load box option 2-4

AC power pedestal 2-5

Procedure 2-1 Unpacking the cabinet 2-7

Procedure 2-2 Preparing the pad 2-10

Procedure 2-3 Preparing the cabinet for installation 2-14

Securing the cabinet to the mounting pad 2-15

Removing eyebolt from cabinet 2-15

Crane operation precautions 2-16

Eyebolt precautions 2-16

Contents

AccessNode 323-3001-210 Issue 1.0

Cabinet weights 2-16

Procedure 2-4 Mounting the cabinet on the pad 2-23

Procedure 2-5 Enabling the door locks 2-31

Connecting commercial power 3-1

How to use this chapter 3-1

Chapter task list 3-1

Prerequisites for installation 3-2

Precautions 3-2

AC power 3-3

Cable entry 3-3

Load box option 3-3

AC power pedestal 3-4

Procedure 3-1 Connecting earth ground to the ac load box 3-5

Procedure 3-2 Wiring the ac load box as a branch circuit 3-7

Procedure 3-3 Wiring the ac load box as a main service entrance 3-10

Procedure 3-4 Connecting earth ground to the ac power pedestal 3-13

Procedure 3-5 Wiring the ac power pedestal 3-17

Installing the OSP cables 4-1

How to use this chapter 4-1

Chapter task list 4-1

Prerequisites for installation 4-2

Precautions 4-2

Cable entry 4-3

Procedure 4-1 Pulling the OSP cabling into the cabinet 4-4

Procedure 4-2 Butting and stripping the VF, miscellaneous, T1 and maintenance

cables 4-8

Procedure 4-3 Butting and stripping the fiber cable 4-12

Procedure 4-4 Installing the cable bonding clamps 4-16

Procedure 4-5 Applying a moisture barrier to the air-core cable 4-20

Routing and terminating OSP T1 and maintenance pairs 5-1

How to use this chapter 5-1

Chapter task list 5-1

Prerequisites for installation 5-1

Precautions 5-2

Cable entry 5-2

Procedure 5-1 Routing and terminating OSP T1 and maintenance pairs 5-3

Routing and terminating the VF cables 6-1

How to use this chapter 6-1

Chapter task list 6-1

Prerequisites for installation 6-2

Precautions 6-2

Cable entry 6-3

Procedure 6-1 Connecting the VF cable pairs 601–1200 to BIX connectors with

the cross-connect 6-4

Procedure 6-2 Connecting the VF cable pairs 1–600 to BIX connectors with the

cross-connect 6-9

Procedure 6-3 Splicing the binder groups using BIX connectors 6-14

Contents

vii

AccessNode Series 800A Outside Plant Cabinet Installation 323-3001-210 Issue 1.0

Procedure 6-4 Connecting the VF cable pairs to BIX connectors without the

cross-connect 6-16

Procedure 6-5 Connecting the VF cable pairs 601–1200 to 710 or 3M MS2 DPM

connectors with cross-connect 6-23

Procedure 6-6 Connecting the VF cable pairs 1–600 to 710 or 3M MS2 DPM

connectors with cross-connect 6-30

Procedure 6-7 Splicing the binder groups using 710 or 3M MS2 DPM

connectors 6-33

Procedure 6-8 Connecting the outside plant cable pairs to 710 or 3M MS2 DPM

connectors without cross-connect 6-36

Routing and splicing the fiber cable 7-1

How to use this chapter 7-1

Chapter task list 7-1

Prerequisites for installation 7-2

Precautions 7-3

Cable entry 7-4

Procedure 7-1 Routing the OSP fiber cable directly to the FPP 7-5

Procedure 7-2 Routing the OSP fibers in split flex tubing to the FPP 7-15

Procedure 7-3 Routing the fiber patch cords from the ABM to the FPP 7-20

Procedure 7-4 Routing fiber to the ABM when no FPP is installed 7-32

Provisioning the external alarms 8-1

How to use this chapter 8-1

Chapter task list 8-1

Prerequisites for installation 8-2

Procedure 8-1 Provisioning and verifying the external alarms 8-3

Procedure 8-2 Wiring customer reserved optional defined external alarms 8-5

Installing and connecting the batteries 9-1

Chapter task list 9-1

Prerequisites for installation 9-1

Battery options 9-2

Battery cables 9-2

Procedure 9-1 Installing 12 V batteries in a cabinet 9-4

Procedure 9-2 Installing 6 V batteries in a cabinet 9-14

Procedure 9-3 Wiring the cabinet when the batteries are installed in the battery

vault 9-26

Adjusting the rectifier and the dc distribution shelf 10-1

How to use this chapter 10-1

Chapter task list 10-2

Prerequisites for installation 10-2

Cautions 10-2

Procedure 10-1 Powering the rectifier(s) 10-4

Procedure 10-2 Adjusting high voltage shutdown 10-11

Procedure 10-3 Adjusting equalize voltage 10-14

Procedure 10-4 Adjusting float voltage 10-16

Procedure 10-5 Adjusting the second or third rectifiers 10-18

Procedure 10-6 Adjusting load sharing for more than one rectifier 10-20

Procedure 10-7 Verifying dc distribution shelf alarms 10-23

viii

Contents

AccessNode 323-3001-210 Issue 1.0

Procedure 10-8 Adjusting dc distribution shelf low voltage alarms 10-26

Procedure 10-9 Adjusting dc distribution shelf low voltage disconnect 10-28

Procedure 10-10 Adjusting dc distribution shelf low voltage disconnect

return 10-30

Finishing the S800A cabinet installation procedures 11-1

How to use this chapter 11-1

Chapter task list 11-1

Procedure 11-1 Installing the protector modules 11-2

Procedure 11-2 Performing commissioning and site testing 11-6

Procedure 11-3 Installing the shipping brackets 11-7

Cabinet maintenance operations 12-1

How to use this chapter 12-1

Chapter task list 12-2

Recommended maintenance 12-3

Replacement parts 12-5

Procedure 12-1 Replacing the batteries 12-6

Procedure 12-2 Replacing the rectifier 12-13

Procedure 12-3 Adjusting the high voltage shutdown for replacement

rectifiers 12-19

Procedure 12-4 Setting the equalize voltage level 12-24

Procedure 12-5 Adjusting the float voltage 12-26

Procedure 12-6 Adjusting the load sharing for replacement rectifiers 12-28

Procedure 12-7 Connecting emergency standby power - ac load box option with

mechanical interlock 12-32

Procedure 12-8 Connecting emergency standby power - attached ac power

pedestal option 12-35

Procedure 12-9 Installing the jumper wire spool 12-38

Procedure 12-10 Using the BIX or binding post test clips 12-39

Procedure 12-11 Using the protector test access cord 12-40

Procedure 12-12 Replacing an internal fan unit in the heat exchanger roof 12-42

Procedure 12-13 Replacing an external fan unit in the heat exchanger roof 12-44

Procedure 12-14 Replacing a fan unit in the air induction roof 12-46

Procedure 12-15 Replacing the equipment fan shelves 12-48

Procedure 12-16 Installing a new optional equipment fan shelf 12-57

Procedure 12-17 Replacing the fan filters in the heat exchanger roof 12-63

Procedure 12-18 Replacing the fan filters in the air induction roof 12-65

Cabinet and equipment wiring and cabling 13-1

Installation information in this chapter 13-1

Grounding 13-4

Cabinet grounding 13-4

Equipment grounding 13-6

AC power distribution 13-7

AC load box 13-8

AC power pedestal 13-11

Rectiﬁer ac input cabling 13-15

DC power distribution 13-16

Rectiﬁer dc output 13-17

DC distribution shelf dc power wiring 13-18

Table des matières

Autres manuels Nortel Matériel réseau

Nortel

Nortel BayStack 100-S Mode d’emploi

Nortel

Nortel 2600 Manuel utilisateur

Nortel

Nortel Meridian 1 Option 11C Manuel utilisateur

Nortel

Nortel C251 Manuel utilisateur

Nortel

Nortel 2340 Manuel utilisateur

Nortel

Nortel NAC Manuel utilisateur

Nortel

Nortel BayStack 100 Series Instructions d'utilisation

Nortel

Nortel Meridian 1 Option 11C Manuel d'installation et d'exploitation

Nortel

Nortel R2MFC Manuel de l'opérateur

Nortel

Nortel Meridian SL-100 Manuel utilisateur

Nortel

Nortel 2340 Manuel utilisateur

Nortel

Nortel Meridian Mail Manuel utilisateur

Nortel

Nortel BCM200 Guide d'installation

Nortel

Nortel BayStack 100-S Manuel de service

Nortel

Nortel HomeOffice II Manuel utilisateur

Nortel

Nortel 5399 Manuel utilisateur

Nortel

Nortel BayStack 650 Mode d’emploi

Nortel

Nortel Passport 4430 Manuel utilisateur

Nortel

Nortel BayStack 100-S Manuel utilisateur

Nortel

Nortel Meridian 1 Option 11C Compact Manuel d'utilisation et d'entretien

Nortel

Nortel RLC Mode d’emploi

Nortel

Nortel BayStack 100-S Manuel utilisateur

Nortel

Nortel 9110 Mode d’emploi

Nortel

Nortel 1800 Mode d’emploi

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur