Nokia RH-57 Series Mode d'emploi

Nokia Customer Care

2112 (RH-57) Series Transceivers

Troubleshooting — Antenna

2112 (RH-57)

Troubleshooting — Antenna Nokia Customer Care

Contents Page

Introduction ..................................................................................................................................................... 3

Internal Antenna is Missing .....................................................................................................................3

Damaged RF Feed Pin or Ground Pin .....................................................................................................4

Wrong Internal Antenna is Installed ......................................................................................................4

Obstructed RF Feed or Ground Pads for Internal Antenna or IHF Speaker Pads .......................5

Grounding of Display Frame .....................................................................................................................6

RUIM Card Flap Grounding .......................................................................................................................7

RF Connector Failure ..................................................................................................................................7

Nokia Customer Care Troubleshooting — Antenna

2112 (RH-57)

Introduction

This troubleshooting guide addresses potential failures that can affect antenna

performance of the 2112 phone, and discusses methods for correction of these failures.

Figure 1: Model 2112 front and back view

Internal Antenna is Missing

Figure 2: Model 2112 chassis assembly

RF feed

IHF speaker

pins

Ground pin

RF shield

2112 (RH-57)

Troubleshooting — Antenna Nokia Customer Care

If no internal antenna is installed, the antenna gain is degraded by more than 25 dB.

• If the internal antenna is missing, install a new one.

• If the radiator looks obviously damaged, replace the internal antenna.

Damaged RF Feed Pin or Ground Pin

Figure 3: Top (left) and bottom (right) views of the 2112 (RH-57) internal antenna

If the RF feed does not touch the PWB, then the antenna gain will degrade by more than

25dB. If the ground pin does not touch the PWB, then the antenna gain may degrade

from 5—10 dB.

Replace the internal antenna if any of the following situations apply:

• Either the RF feed pin or ground pin are broken or bent such that either pin will

not touch the PWB

• The springs for the RF or ground pin appear damaged

• The slot in the radiator has a significantly different shape

• Obvious damage to the radiator (e.g., dents, corrosion)

• The pin is stuck or has excessive friction in the plastic tube/guiding feature

resulting in the spring not working properly

• Either of the IHF speaker pins is damaged or if the IHF speaker is nonfunctioning

Wrong Internal Antenna is Installed

Figure 4: Top views of the 3100 (RH-19) (left) and 2112 (RH-57) (right) antennas

The 2112 and 3100 antennas are similar in appearance. The important visual difference in

the antennas is that the slot pattern is very different. Also, the 2112 antenna is thicker

than the 3100 antenna and also has a spacer on its back side.

IHF speaker

pins

RF pin Ground pin

Spacer

IHF speaker

port Ground pin RF pin

Radiator

Nokia Customer Care Troubleshooting — Antenna

2112 (RH-57)

If the wrong antenna is installed, install the correct one.

Figure 5: Bottom views of 3100 (left) and 2112 (right) antennas

Obstructed RF Feed or Ground Pads for Internal Antenna or IHF Speaker Pads

Figure 6: PWB layout of RF feed and ground pads and IHF speaker pads

If the RF feed pad is obstructed, removed, or covered, the RF feed pin will not touch the

PWB and the antenna gain will degrade by more than 25 dB. If the ground pad is

obstructed, removed, or covered, the ground pin will not touch the PWB and the antenna

gain may degrade by about 5—10 dB.

• If corrosion is present or the pad is missing, replace the PWB and the phone.

• If either pad is obstructed or covered, clear or clean the pad.

If the Internal Hands Free (IHF) speaker pads are obstructed, removed, or covered, the IHF

speaker will not produce sound.

• If corrosion is present or the pad is missing, replace the the PWB and the phone.

• If either pad is obstructed or covered, clear or clean the pad.

Pad for ground pin Pad for RF pin

IHF speaker pads

2112 (RH-57)

Troubleshooting — Antenna Nokia Customer Care

Grounding of Display Frame

Figure 7: Display assembly

Note that the display frame is grounded to the PWB through the two top screws. The

grounding of the display frame impacts the radiation performance of the phone.

• If the screws are loose, then tighten them.

• If the screw bosses are stripped, replace the chassis.

• If the screws are missing, install new ones.

The middle screws should not touch the metal in the LCD frame, the metal shield over

the keypad, the PWB, or the RF shield. When driving in these screws, be sure to drive

them in straight. If the screws are driven in at an angle, it is much more likely that the

screws will touch the PWB or the RF shield. If the screws touch, the antenna

performance could change by about 1 dB.

Ungrounded screw

Grounded screw

RF connector

Nokia Customer Care Troubleshooting — Antenna

2112 (RH-57)

RUIM Card Flap Grounding

Figure 8: Conductive sticker grounding RUIM card flap to RF shield

The RUIM card flap needs to be grounded to the RF shield with a conductive sticker

(see Figure 8). If the sticker is damaged or missing, then the radiated sensitivity could be

reduced by 4—8 dB.

• If the conductive sticker is missing or ripped, replace the sticker.

If the RF shield needs to be disassembled from the chassis, the sticker may be damaged

because the sticker needs to be removed to change the antenna module or the RUIM

card flap.

• If you replace the RUIM card flap or RF shield, replace the type labels and

conductive sticker.

• You may need to replace the RF shield and all the labels because the conductive

sticker is located underneath other labels.

RF Connector Failure

The RF connector could fail by not connecting the RF input to the RF output of the RF

connector. If this happens, the antenna gain will degrade by about 25 dB. Check for this

by testing for DC conductivity between the RF input and RF output of the RF connector.

Note that the DC conductivity test must be done without any cables attached to the RF

connector. Because the RF connector is also a switch, the RF output is disconnected from

the RF input when a cable is inserted into the RF connector. When a cable is inserted, the

RF input is connected to the RF connector.

• RF input — connector to a duplexor

• RF output — connects to the antenna pad through vias

• RF connector — connects to a coaxial cable

If the RF input is not connected properly to the RF output, replace the RF connector.

Conductive sticker

RF shield

RUIM card flap

2112 (RH-57)

Troubleshooting — Antenna Nokia Customer Care

This page intentionally left blank.

Autres manuels pour RH-57 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Nokia Émetteur-récepteur

Nokia

Nokia RM-11 Series Mode d'emploi

Nokia

Nokia NSM-5 SERIES Mode d’emploi

Nokia

Nokia RM-11 Series Mode d'emploi

Nokia

Nokia NKC-1X Series Mode d’emploi

Nokia

Nokia NSW-6 Series Mode d’emploi

Nokia

Nokia RH-27 Series Mode d’emploi

Nokia

Nokia NSE-5 Series Manuel utilisateur

Nokia

Nokia NSE-6 SERIES Manuel utilisateur

Nokia

Nokia RH-27 Series Mode d'emploi

Nokia

Nokia NSB-5 Series Mode d’emploi

Nokia

Nokia N92 RM-100 Manuel utilisateur

Nokia

Nokia RH-10 Series Guide de démarrage rapide

Nokia

Nokia RH-41 Series Mode d’emploi

Nokia

Nokia NSM-2 Series Instructions d'installation

Nokia

Nokia NPM-6 Series Manuel utilisateur

Nokia

Nokia RM-11 Series Mode d'emploi

Nokia

Nokia RH-21 Series Manuel utilisateur

Nokia

Nokia NHM-2nx Series Mode d'emploi

Nokia

Nokia RM-11 Series Instructions d'installation

Nokia

Nokia RH-20 Manuel utilisateur

Nokia

Nokia NPC-1 Series Mode d’emploi

Nokia

Nokia NSC-1 SERIES Guide de configuration

Nokia

Nokia RH-34 Series Mode d’emploi

Nokia

Nokia NSB-5 Series Mode d’emploi

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur