Nokia NPM-6 Series Manuel utilisateur

Customer Care Solutions

NPM-6/6X Series Transceivers

Issue 2 06/03 CopyrightNokia. All rights reserved

Disassembly and Assembly

Instructions

NPM-6/6X

Disassembly and Assembly Instructions CCS Technical Documentation

Page 2 Copyright Nokia. All rights reserved Issue 2 06/03

Disassembling instructions ............................................................................................ 4

Exchange of system connector....................................................................................... 6

Exchange of battery connector...................................................................................... 8

CCS Technical Documentation Disassembly and Assembly Instructions

NPM-6/6X

Issue 2 06/03 CopyrightNokia. All rights reserved Page 3

Disassembling instructions

Note! It is only allowed to reassemble C-Cover (phone) once. For second reassem-

bling use of new C-Cover is mandatory! Use new screws in general.

Press the grip markings on both sides of the B-Shell and

remove B-Shell.

To remove the A-Shell press Locking Springs as shown and

pull A-Shell from the unit.

Tightening torques for screws (Note! Two tightening

torques!): -screws 1-4, use 40 Ncm

-screws 5-6, use 25 Ncm.

Tightening order for screws is from 1 to 6. When

tightening the screws 5 and 6 it is necessary to press

strongly the system connector against C-cover to avoid

sealing tape twisting in the system connector. If the

sealing tape twists with screwassembly it is not

waterproof anymore. Note! The screws can be assembled

only once.

Remove engine from C-Cover.

Separate the UI-Module from Radio Module carefully,

because of the board-to board-connector.

Use tweezers to remove Vibra Motor.

1

2

5

6

3

4

NPM-6/6X

Disassembly and Assembly Instructions CCS Technical Documentation

Page 4 Copyright Nokia. All rights reserved Issue 2 06/03

Remove Earpiece. Note the guiding pin when assembling. Remove Keymat.

CCS Technical Documentation Disassembly and Assembly Instructions

NPM-6/6X

Issue 2 06/03 CopyrightNokia. All rights reserved Page 5

Exchange of system connector

The System Connector is attached with double-sided

adhesive gasket to C-Cover. Also note the gasket on C-

Cover.

Press SRT-6 between C-Cover and System Connector and

remove Battery Cover.

Press again SRT-6 between C-Cover and System Connector

and remove System Connector.

Remove System Connector.

To remove the remaining adhesive gasket use SRT-6 only.

Do not use sharp-edged tools for this procedure.

Remove protection foil from System Connector.

NPM-6/6X

Disassembly and Assembly Instructions CCS Technical Documentation

Page 6 Copyright Nokia. All rights reserved Issue 2 06/03

Place System Connector to its guidance exactly. Now press connector to C-Cover firmly, while taking care

not to slip C-Cover on your table.

CCS Technical Documentation Disassembly and Assembly Instructions

NPM-6/6X

Issue 2 06/03 CopyrightNokia. All rights reserved Page 7

Exchange of battery connector

These are the two soldered support angles. Use a side cutter to cut the support angles.

Push tweezers in outer openings of battery connector and

lift up the plastic cover.

Desolder all pins and clean the pads.

Note that you need a soldering iron with higher

temperature when cleaning or soldering the grounding

pad.

Tin one of pads to fix the connector before soldering the

following pins.

NPM-6/6X

Disassembly and Assembly Instructions CCS Technical Documentation

Page 8 Copyright Nokia. All rights reserved Issue 2 06/03

Note location of connector pins and support angles to fit

them precisely.

Solder first support angle. When position is exact, solder

the other pins.

Autres manuels pour NPM-6 Series

4

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Nokia Émetteur-récepteur

Nokia

Nokia NPM-6 Series Manuel utilisateur

Nokia

Nokia NSB-9 Mode d’emploi

Nokia

Nokia NSE-5 Series Instructions d'installation

Nokia

Nokia NHM-1 Series Mode d’emploi

Nokia

Nokia NPM-10 Series Mode d’emploi

Nokia

Nokia NSM-4 Series Instructions d'installation

Nokia

Nokia NKC-1X Series Mode d’emploi

Nokia

Nokia RH-34 Series Mode d’emploi

Nokia

Nokia NSE-6 SERIES Mode d’emploi

Nokia

Nokia NME-2A Series Mode d’emploi

Nokia

Nokia NPM-6 Series Mode d’emploi

Nokia

Nokia RH-27 Series Mode d’emploi

Nokia

Nokia NSM-3 Instructions d'installation

Nokia

Nokia NSC/W-1/3 Series Manuel utilisateur

Nokia

Nokia NPC-1 Series Mode d’emploi

Nokia

Nokia NSE-5 Series Manuel utilisateur

Nokia

Nokia NSM-5 SERIES Instructions d'installation

Nokia

Nokia NSB-1 Series Mode d’emploi

Nokia

Nokia NHM-8NX Series Mode d’emploi

Nokia

Nokia NSB-1 Series Manuel utilisateur

Nokia

Nokia RH-21 Series Manuel utilisateur

Nokia

Nokia NSM-3 Mode d’emploi

Nokia

Nokia NKC-1X Series Mode d’emploi

Nokia

Nokia NHM-2nx Series Mode d'emploi

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur