NewLine VNC Series Manuel d'instructions
The symbol of the crossed out wheeled bin indicates this product should not be
placed in municipal waste. Instead, dispose of waste equipment by handing it over to
a designated collection point for the recycling of electrical and electronic equipment.
Thank you for choosing Newline collaboration touch screen.
1
Symbol Conventions
Symbols are used in this document to indicate operations that require special attention. The
symbols are dened as follows:
Used to supplement explanations or descriptions of current operations.
Used to signal equipment or environmental safety warnings. Not taking
heed of said warnings could result in potential danger, equipment
damage, data loss, reduced equipment performance, or other
unpredictable results.
Used to signal potential danger which could result in severe injury or
even death.
WARNING
CAUTION
NOTE
2
Safety Instruction
For your safety, please read the following instructions before you use the product. Improper
operations may cause severe injury or property damage. Please refrain from repairing the
product on your own.
If major failures occur, disconnect the product from power source
immediately.
Major failures include the following:
●Smoke, peculiar smell or abnormal sound discharged from the product.
●No image or sound is displayed, or if image error occurs.
If the above scenarios occur, do not continue using the product. Disconnect
power supply immediately and contact professional staff.
Do not drop liquid, metal or anything combustible into the product.
●If liquid or pieces of metal get into the product, turn off the power and disconnect
the power source, then contact professional staff.
●Supervise children when they are close to the product.
Place the product on a stable surface.
An unstable surface includes but is not limited to an inclined surface, a shaky stand,
desk or platform, which might cause turnover and damage.
Do not open the cover or modify the product on your own.
High voltage components are installed in the product. When you open the cover,
high voltage, electric shock, or other dangerous situations may occur.
If inspection, adjustment, or maintenance is required, contact the local distributor
for help.
Use the specied power supply voltage.
●
To prevent the product from being damaged, do not use cables other than the
one provided with the product.
●
Use a three-wire socket and ensure that it is properly grounded.
●
Pull out the power plug from the socket if the product is not to be used for a
long period.
Regularly clean the dust and metal around the power plug.
●Fire or electric shock may be caused if the product is powered on, when you
are cleaning.
●Pull out the power plug before cleaning it with a dried cloth.
Do not place items on top of the product.
● Do not put items, such as a liquid container (a vase, owerpot, cosmetics or
liquid medicine) on the top of the product.
●If any water or liquid is spilled on the product, a short circuit may occur and
cause re or electric shock.
WARNING
3
Do not install the product in an improper place.
●Do not install the product in humid places, such as the bathroom, the shower
room, near windows, or outdoor environments that experience rain, snow or
other harsh weather. Avoid installation near hot spring vapor. The preceding
environments may cause faults in the product or electric shock under extreme
conditions.
● Do not put expose the product to a re source, such as an ignited candle.
Pull out the power plug during thunderstorms.
●Do not touch the product during a lighting storm to avoid electric shocks.
●Install or place components that supply high enough voltage out of the reach
of children.
Do not touch the power cable with wet hands.
WARNING
Do not install the product in high temperature environments.
●Do not install the product near a heat source, such as a radiator, a heat reservoir, a
stove or other heating products.
●Do not expose the product to direct sunlight, which may cause high temperatures and
subsequent faults in the product.
Transport of the product.
●
Pack the product for transport or maintenance by using the cartons and
cushioning material provided with the product.
●
Keep the product vertical during transport. The screen or other components
are easily broken if the product is moved inappropriately.
●
Before you move the product, disconnect all external connections and separate
all toppling preventing products. Move the product carefully to prevent it from
being hit or squeezed, especially the screen, which may cause injury if broken.
Do not cover or block up any vents on the product. Any overheated
components may cause re, damage the product, and shorten the
product’s service life.
●Do not lay the product down where the venting surface will be covered.
●Do not install the product on a carpet or cloth.
●Do not use a cloth such as table cloth to cover the product.
CAUTION
4
Keep away from the product when using a radio.
The product complies with the international EMI standard regarding prevention
of radio interference. However, interference may still exist and cause noises to
the radio. If noise occurs in the radio, try the following solutions.
● Adjust the direction of the radio antenna to avoid the interference from the product.
● Keep the radio away from the product.
Do not damage the power cable.
● Do not damage, change, twist, bend, or forcibly drag the power cable.
● Do not put weights (such as the product itself) on top of the power cable.
● Do not forcibly drag the cable when you pull out the power plug. If the power
cable is damaged, please contact the local distributor to repair or replace it.
● The power cable in the accessory box is for this product only. Do not use it on
other products.
Correct battery usage.
● Galvanic corrosion, electric leakage, and even re may be caused by improper
battery usage.
● It is recommended to use the designated type of battery and install the battery
by correct electrodes (positive and negative).
● Do not use a new battery alongside a used one.
● Take out the batteries if the remote control is not to be used for a long period.
● Do not expose the batteries to overheated environments such as sunlight and ring.
● Dispose of used batteries based on your local regulations.
Suggestions for usage:
● Use the product in an environment with comfortable lighting. It is harmful to
your eyes to watch in a too bright or too dark environment.
● Rest your eyes after an extended period of usage.
● Keep sufcient distance from the product to protect your eyes and prevent eyestrain.
● Adjust the volume to an appropriate level, especially at night.
● Use amplier equipment as the audio input source with caution. If you must
use amplier equipment, the input power should not exceed the maximum
of speaker power. Otherwise, the speaker can become overpowered and damaged.
Special note:
● Zero energy consumption can be achieved when the product isn’t connected
to any external power supply. Therefore, it is recommended to shut down the
device when not watching.
● Under the premise of ensuring the display quality, the energy consumption
can be reduced by reducing the brightness of the display.
● This product can be paired with various internal PC, which can be upgraded or
replaced according to your needs.
CAUTION
5
AProduct Overview
Appearance
◆Front View
● TT-6519VNC/TT-7519VNC/TT-8619VNC:
There are electronic components in the plastic parts at the bottom of the product. If
the plastic parts are damaged, the camera or the product may malfunction. To avoid
damage to the plastic parts, please pay attention to the following:
● Do not squeeze, knock at or disassemble the plastic parts.
● Do not place heavy objects on plastic parts.
● When transporting the product, do not impact the plastic parts at the bottom.
● When transporting the product, do not place the plastic parts on the ground.
CAUTION
5
1
3
6
6
6 6
7
24
8
◆Rear View
● TT-6519VNC/TT-7519VNC/TT-8619VNC:
6
10
9
11 11 12
13
14
15
1Touch screen 6Microphone 11 Speaker
2Light sensor 7Camera 12 Rear port 1
3Power button 8Camera indicator 13 Rear port 2
4IR receiver 9Power socket 14 Internal PC
5Bottom plastic part 10 Power switch 15 Bar interface
Front Buttons
Button Function description
Power on/off.
● In power-on state, press it to enter the sleep state,
press and hold for 2 seconds to shut down.
● In power-off state, press it to turn on the power.
Rear Port
Voltage/current output of the power supply: 5V/2A (Max.); please follow the requirements and
do not use it on products that do not meet the specications, or else it may cause re or electric
shock.
WARNING
7
Network reset button
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels NewLine écran tactile
Manuels écran tactile populaires d'autres marques
Elecro Engineering
Elecro Engineering Poolsmart Plus Instructions d'installation
Johnson Controls
Johnson Controls IQ4 HUB Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET2270L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET1002L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems 3201L Manuel utilisateur
Duratec
Duratec S15 Manuel utilisateur
