Network Technologies PWR-RMT-RBT Manuel utilisateur

Man095 Rev 10/23/07

PWR-RMT-RBT

Remote Power Reboot Switch

Installation and Operation Manual

ENVIROMUX®Series

NETWORK

TECHNOLOGIES

INCORPORATED

Tel:330-562-7070

Fax:330-562-1999

1275 Danner Dr

Aurora, OH 44202

www.networktechinc.com

NTI

Man095 Rev 10/23/07

TRADEMARK

ENVIROMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries.

retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.

CHANGES

The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the

right to make changes in the product design without reservation and without notification to its users.

WARRANTY INFORMATION

The warranty period on this product (parts and labor) is two (2) years from the date of purchase. Please contact Network

Technologies Inc at (800) 742-8324 (800-RGB-TECH) or (330) 562-7070 or visit our website at http://www.networktechinc.com

for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns.

Man095 Rev 10/23/07

Page 2

Important Safety Instructions

When using this product, basic safety precautions should always be followed to reduce the

risk of fire, electric shock, and injury to persons, including the following:

1. Read and understand all instructions.

2. Follow all warnings and marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a

damp cloth for cleaning.

4. Do not use this product in an outdoor environment or near water, for example, near a bath tub, wash bowl,

kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to

the product.

6. Slots and openings in this product and the back or bottom are provided for ventilation to protect it from

overheating; these openings must not be blocked or covered. The openings should never be blocked by placing

the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a

radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is

provided.

7. This product should be operated only from the type of power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult your dealer or local power company.

8. This product is equipped with a three wire grounding type plug, a plug having a third (grounding) pin. This plug

will only fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into

the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the

grounding type plug. Do not use a 3-to-2 prong adapter at the receptacle; use of this type adapter may result in

risk of electrical shock and/or damage to this product.

9. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by

persons walking on it.

10. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.

11. Never push objects of any kind into this product through slots as they may touch dangerous voltage points or

short out parts that could result in a risk of fire or electrical shock. Never spill liquid of any kind on the product.

12. To reduce the risk of electrical shock, do not disassemble this product, but take it to a qualified serviceman when

some service or repair work is required. Opening or removing covers may expose you to dangerous voltages or

other risks. Incorrect re-assembly can cause electric shock when the appliance is subsequently used.

13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following

conditions:

a) When the power supply cord or plug is damaged or frayed.

b) If liquid has been spilled into the product.

c) If the product has been exposed to rain or water.

d) If the product does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operating instructions because improper adjustment of other controls

may result in damage and will often require extensive work by a qualified technician to restore the

product to normal operation.

e) If the product has been dropped or has been damaged.

f) If the product exhibits a distinct change in performance.

14. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of

electric shock from lightning.

15. Do not use the telephone to report a gas leak in the vicinity of the leak.

16. Do not exceed the maximum output rating of the auxiliary power receptacle.

Save These Instructions

Page 3

General Description

The PWR-RMT-RBT (iBoot) is a network attached, IP addressed, web controlled AC power switch. Anyone

with a web browser can access the switch to perform power On, Off or Power Cycle (Reboot or

Power Burst). PWR-RMT-RBT is password protected for security.

PWR-RMT-RBT features international standard IEC320 connections and is compatible with power mains

worldwide. Dual Ethernet jacks with built-in 10/100 switch make installation easy.

Uses

• Remote reboot of any device, routers, servers, kiosks, etc. The device to be rebooted need not

be network attached.

• Secure sensitive devices by keeping them powered off when not in use. This prevents hackers

from seeing them at all times.

• Power down equipment when not needed for power savings and to save on wear and tear.

• Power up alert devices like sirens, lamps, messages; or control environmental system like

heaters, coolers pumps, etc.

Multiple Control Options iBoot

Web Controlled

Power Switch

In addition to the Web control

capabilities, iBoot features several other

means to operate automatically

or under computer control.

Auto-Ping: The Auto-Ping feature allows

the switch to automatically detect failed Dual

equipment and perform a timed reboot 10/100

or other power control function (like Ethernet

turning on an indicator or siren). You

set any IP address to be periodically

pinged. When iBoot no longer detects PC with

Web Browser

a response from the address, the

programmed power control function is

actuated.

Pwr Out

Inter- or

Intra- Net

Pwr In

Heartbeat Monitor: Like the Auto-Ping in reverse, this feature uses a periodic message sent to the

iBoot from a device. When that message is not received, the iBoot will perform the programmed

power control function.

iBoot Control Program: NTI offers an application to simplify operation of the iBoot. The iBoot

Control Program operates one iBoot from a command line or window. It can be called by other

programs to create an automated reboot system.

Direct TCP Control: iBoot can be controlled directly via messages sent via TCP. This feature allows

programmers to add power control directly to their application and build automated scripts in any

language to operate iBoot.

Page 4

Hardware Installation

Ethernet Connections

iBoot supports 10/100 Ethernet using unshielded twisted

pair (Cat 5) cabling. Two network jacks, with built-in

Ethernet switch, are provided. They are auto-sensing for

10/100 and Uplink/Downlink. A Link LED for each jack

indicates when the connection to the network is properly

established. The built-in switch allows one cable from the

wiring closet to be used for both iBoot and the device it is

powering (or any other device). Use of both network

jacks is optional.

Note: iBoot supports DHCP. If your network uses a

DHCP server, it will automatically assign an IP

address when iBoot is first powered up on the

network. If you do not use DHCP there are

several other methods of assigning an IP address.

Please read the Initial Configuration section, page

5 for more details.

AC Power Connections

Connect the device to be powered ON and OFF to the

IEC receptacle marked Switched Outlet. An IEC 320 to

North American (NEMA 5-15) power cord is included for

connecting the iBoot outlet to the device to be controlled.

If a cord with a different terminating receptacle is

required, be sure it is properly rated and meets all the

required local electrical standards. If the device to be

powered uses an IEC320 receptacle and detachable

power cord, an IEC to IEC extension cord can be used.

The iBoot can be connected to a power strip to allow

simultaneous control of multiple devices.

Make sure that the combined load of all controlled

devices does not exceed 12 Amps for 105-125VAC or 10

Amps for 210-240VAC.

An LED Indicator next to the Switched Outlet will be On to

indicate that the power is On at that outlet. This LED will

turn Off to indicate that the power is Off to the outlet.

Connect the supplied power cord to the connector labeled

AC Input, and the other end to your AC source. If a

power cord with a different terminating plug is required,

be sure it is properly rated and meets all the required

local electrical standards.

A/C Input

Networked Device

PC Workstation, Router Etc.

10/100 base-T

Unshielded

Twisted Pair

Connect Device to be Powered to iBoot

Use either:

IEC to NEMA Extension Cord

(supplied)

- OR -

IEC to your country specific

outlet (not supplied)

- OR -

IEC to IEC Extension Cord

(not supplied)

Switched

Outlet On

IEC to NEMA

Extension Cord

Power Controlled Device

105-125 VAC 12A

210-240 VAC 10A

Switched

Outlet On

IEC to IEC

Extension Cord

105-125 VAC 12A

210-240 VAC 10A

Uplink

Downlink A/C Input

Connect to Power

Source

Use Included Cord for

North America. For other

locations, use locally

approved power cord.

Page 5

Initial Configuration

The iBoot Setup Utility supplied on the distribution CD provides the easiest means to find and

configure your iBoot for use. It can discover all the iBoots on your network, display the current IP

address of each, and allow setting of any valid IP address. The Setup Utility is available on the

distribution CD.

Install and run the iBoot Setup Utility:

1. Load the iBoot CD. (The CD supports

only Windows)

2. Click on Setup.exe

3. Install the iBoot Setup Utility

4. Run the iBoot Setup Utility

Note: The IP address can only be set within the

first two minutes of powering up the iBoot, and

requires a power restart of the iBoot after setting

the IP address. Make sure you have physical

access to the iBoot before attempting to set the

IP Address. The Setup Utility will only work with

iBoots on the same local subnets as the iBoots.

Once the iBoot Setup Utility is run, click on

Discovery to display all the iBoots on your

network. New iBoots will display with the name

Set Location and have either the factory default

IP address of 192.168.1.254 or an IP address

that was automatically assigned by the DHCP

server on your network. If the IP address was

assigned by a DHCP server, no changes to the

IP Address are required.

The IP address field also indicates the IP port

that is used by the iBoot. The standard port for

web browser control is factory default Port 80.

Change the IP Address

1. Click on the row containing the iBoot to

be set. The row will become highlighted.

2. Click on the Set IP Address button.

3. Enter the new IP Address into the form. Click OK when done.

4. A confirmation box is displayed. Click OK to clear the box.

5. Power cycle the iBoot to finish the process. A reminder of which iBoots that require this

power down – power up procedure are indicated by a .

Page 6

Once the IP Address is set and the iBoot is power cycled, other all other operational features of the

iBoot can be set up. Click on Discover again to refresh the display, highlight the desired iBoot and

click on Launch Browser. Follow the instructions on Page 9 to configure the iBoot.

The iBoot Setup Utility can also be used to return an iBoot to its Factory Default condition. This can

be used to recover an iBoot with a lost password. Highlight an iBoot from the display and click

Factory Defaults. This must also be done within the first two minutes of powering up the iBoot.

Other ways to set the IP Address

1. Automatically from a DHCP Server

2. Web Browser via the Set-up Page

3. ARP / Ping

iBoot comes with factory installed IP address 192.168.1.254 and ready to accept a new IP address

from a DHCP Server. If you network has a DHCP server, it will automatically assign an IP address to

iBoot the first time it is connected and powered up.

Setting the IP address from a DHCP Server

A DHCP server will automatically assign an IP address (dynamic address) as well as Subnet Mask

and Gateway to the iBoot. If you power up iBoot without a fixed (static) IP address, the DHCP

server will be able to assign an IP address. This is the factory default setting for iBoot. Once an IP

address is assigned, you must check the DHCP server or use the iBoot Setup Utility to see what

address is assigned to iBoot.

If you set the IP address using another method, the address becomes static. To return iBoot to

dynamic addressing using DHCP, change the IP address, using the web browser to 0.0.0.0

Setting the IP address using Web Browser

To set the IP address using a Web Browser, connect the Ethernet connection to your local network

and apply power to iBoot.

Open your browser and access iBoot by entering the default (192.168.1.254) or current IP address

into your browser's Address window. Enter the password (the factory default is PASS). Click on

Setup and follow the instructions on Page 9.

Setting the IP address using ARP / Ping

Notes: For security purposes, this may only be done within the first 2 minutes of powering up the

iBoot. If the iBoot has received an IP address from a DHCP server, this technique will not

work.

The ARP technique uses a PC running a command line (DOS Window) to set the IP Address. To set

the IP address using ARP, connect the iBoot to your local network and apply power. The IP address

to be assigned to iBoot must be use the same network segment as the computer assigning the

address. ARP does not work across routed or switched networks.

To set the IP address using ARP, the hardware (MAC) address must be known. This address is

located on the bottom of the unit. The syntax for the MAC address is: nn-nn-nn-nn-nn-nn

Page 7

Windows (98 and Later)

1. Open a DOS window. (Run: Command)

2. Type the following command:

arp -s <IP Address> <MAC Address>

Where <IP Address> is the desired IP address (in dotted decimal) for the iBoot and the

<MAC address> is the MAC Address of the iBoot. The MAC Address of the iBoot is located

on bottom of the unit.

Example: arp -s 63.211.86.165 00-50-c2-05-01-c1 <enter>

|new IP addr| |---MAC addr----|

3. Ping the iBoot to program the IP address into the iBoot.

Type: ping <IP Address>

Note: If the ping command returns “host not responding” 4 times then the address has not

been programmed properly. The process must be run within two minutes of powering

up the iBoot, and not have been set by a DHCP server. Check the IP or MAC

Address. Repeat step 2. If the problem persists, contact NTI.

4. Delete the entry from the ARP cache by typing:

arp -d <IP Address>

5. Ping the iBoot to confirm that it has been programmed.

If the iBoot fails to respond, repeat steps 2-4 above. If the problem persists, contact NTI.

Unix, Linux, MAC and others

Consult your systems administrator for information on other means of setting an IP Address. The

unit should be pinged after the IP Address has been set to confirm proper operation.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Network Technologies Changer

Network Technologies

Network Technologies SERIMUX-CS-x Manuel utilisateur

Network Technologies

Network Technologies NTI High Density DVI USB KVM Switch... Manuel utilisateur

Network Technologies

Network Technologies Console Switch Manuel utilisateur

Network Technologies

Network Technologies CAT5 Primux Manuel utilisateur

Network Technologies

Network Technologies NTI VOPEX VOPEX-USBV Manuel utilisateur

Network Technologies

Network Technologies ST-xUO Manuel utilisateur

Network Technologies

Network Technologies UNIMUX-USBV-xO Manuel utilisateur

Network Technologies

Network Technologies SERIMUX-S-x Manuel utilisateur

Network Technologies

Network Technologies VOPEX-USBV-2 Manuel utilisateur

Network Technologies

Network Technologies KEEMUX-USBV-xU Manuel d'utilisation

Network Technologies

Network Technologies SERIMUX-TERM-CS-16/8 Manuel utilisateur

Network Technologies

Network Technologies UNIMUX-DVI-xHD Manuel utilisateur

Network Technologies

Network Technologies ST-nXm-U Manuel utilisateur

Network Technologies

Network Technologies SM-nXm-C5AV-LCD Manuel utilisateur

Network Technologies

Network Technologies PRIMUX-16X64 Manuel utilisateur

Network Technologies

Network Technologies PRIMUX-16X64 Manuel utilisateur

Network Technologies

Network Technologies KEEMUX-P2 Manuel utilisateur

Network Technologies

Network Technologies SE-DVI-2 Manuel utilisateur

Network Technologies

Network Technologies IPDU-Sx Manuel utilisateur

Network Technologies

Network Technologies NTI PRIMUX PRIMUx-UZR Manuel utilisateur

Network Technologies

Network Technologies KEEMUX-P2 Manuel d'utilisation

Network Technologies

Network Technologies VEEMUX SM-8X4-HDA Manuel utilisateur

Network Technologies

Network Technologies NODEMUX HD Series Manuel utilisateur

Network Technologies

Network Technologies NTI UNIMUX UNIMUX-USBV-4 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur