NetComm NWL-15 Manuel utilisateur

Quick Start Guide

Light Industrial M2M Router Plus

NWL-15

| Wireless M2M

Quick Start Guide

This quick start guide is designed to get you up and running quickly with your new

NetComm Wireless NWL-15 router. More advanced set up instructions can be

found in the user guide which can be downloaded from

www.netcommwireless.com/product/m2m/nwl-15

| Wireless M2M

NWL-15 - Light Industrial M2M Router Plus

Package contents

This package includes

1. 1 x NetComm Wireless NWL-15 router

2. 1 x Six-way terminal block

3. 1 x 1.5m Yellow Ethernet cable 8P8C

4. 2 x CDMA antennas

5. 1 x DIN rail mounting bracket

6. 1 x Quick start guide (not shown)

3 4 5

| Wireless M2M

Device overview

ITEM DESCRIPTION

1Main antenna

socket

SMA female connector for main antenna.

2Auxiliary (Aux)

antenna socket

SMA female connector for auxiliary antenna (receive diversity).

3GPS antenna

socket

SMA female connector for GPS antenna.

4Mini USB 2.0

OTG port

Provides connectivity for external storage or a USB Ethernet dongle.

Supplies up to 0.5A to connected device.

5Serial port Female DB9 port supporting 9-wire RS-232, RS-485 or RS-422

(software selectable).

| Wireless M2M

NWL-15 - Light Industrial M2M Router Plus

ITEM DESCRIPTION

6Six-way

terminal

block connector

Connect power source, ignition and I/O wires here. Power, ignition

and I/O wires may be terminated on the supplied terminal block and

connected to a power source. Refer to the diagram and table under

Step 3 of the Installing your device section for correct wiring of the

terminal block. Operates in the 8-40V DC range.

7Reset button • Press and hold for less than 5 seconds to reboot to normal mode.

• Press and hold for 5 to 15 seconds to reboot to recovery mode.

• Press and hold for 15 to 20 seconds to reset the router to factory

default settings.

8RJ45 Ethernet

port

Connect one or several devices via a network switch here.

| Wireless M2M

Getting started

Depending on your individual setup, you may need certain components to

congure your device correctly.

External power supply unit for the NetComm Wireless NWL-15 router

(not included).

Flathead screwdriver for terminating power input wires.

Notebook or PC for advanced conguration.

Additional fasteners and screwdrivers for specic wall or rail mounting.

Mounting options

The NetComm Wireless NWL-15 router can be installed quickly and easily in a

variety of locations.

MOUNT TYPE DESCRIPTION BENEFITS

Wall mount a) Flat against the wall Slimline form factor, close to wall

b) Perpendicular to the wall Small wall footprint

c) Mount via DIN rail bracket Easy to remove

C Section DIN rail mount Slide onto a rail Simplicity

Top hat DIN rail mount Mount on a bracket and

slide onto a rail

Simplicity. Can mount in

between other devices

Desk mount Stand on a desk Simplicity, versatility

DIN RAIL MOUNTING BRACKET

1Push to release

2V Bend allows you to snap the DIN

bracket onto the middle of a DIN rail,

rather than sliding it onto the end.

| Wireless M2M

NWL-15 - Light Industrial M2M Router Plus

C Section DIN

rail mount

Top hat DIN rail mount

Desk mount

Wall mount

a) Flat against the wall

b) Perpendicular to the wall

c) Mounted via DIN rail bracket

| Wireless M2M

Overview of LED indicators

LED ICON NAME COLOR STATE DESCRIPTION

Power Off Power off

Double ash Powering up

On Power on

On Power on in recovery mode

Slow ashing Hardware error

Network On Connected via WWAN

Blinking1Trafc via WWAN

Slow ashing Connecting data session

On Registered network

Slow ashing Registering network

On Can’t connect

Slow ashing Not activated

Signal

strength

On EVDO coverage

On CDMA 1x coverage

1 The term “blinking” means that the LED may pulse, with the intervals that the LED is

on and off not being equal. The term “ashing” means that the LED turns on and off at

equal intervals.

| Wireless M2M

NWL-15 - Light Industrial M2M Router Plus

Installing your device

Step 1: Attach the antennas

The NetComm Wireless NWL-15 router is shipped with caps on the Main, Auxiliary

and GPS antenna sockets. To attach the antennas, rst remove the socket caps

from the Main and Auxiliary antenna sockets then screw the antennas onto the

sockets by turning them in a clockwise direction. Please refer to the Device

overview section for the antenna socket layout. If you have purchased a GPS

antenna, remove the socket cap from the GPS antenna socket and attach the

antenna to the socket in the same manner.

Step 2: Mount the router

Mount your router in a suitable location using the options listed in the Mounting

options section.

When selecting a location to mount the NetComm Wireless NWL-15 router, keep

in mind that it features two high performance antennas designed to provide

optimum signal strength in a wide range of environments. If you nd the signal

strength is weak, try moving the router to a different place, mounting it differently or

changing the orientation of the antennas.

The signal strength LEDs update within a few seconds with a rolling average signal

strength reading. When selecting a location for the router, please allow up to 20

seconds for the signal strength LEDs to update before repositioning.

| Wireless M2M

Step 3: Connect the power and Ethernet cables

Connect power to your router using one of the following options.

DC power via 6-pin connector

Remove the attached green terminal block from your router and connect to the

router’s power socket using a DC power supply, sold separately.

DC power via eld terminated power source

If an 8-40V DC power supply is available, you can insert the wires into the supplied

terminal block to power your router. Use a athead screwdriver to tighten the

terminal block screws and secure the power wires, making sure that you have

correctly wired the terminal block as illustrated below.

TERMINAL DESCRIPTION

+Positive wire for power.

-Ground wire.

i Dedicated terminal for ignition detection.

I/O Three terminals used for input/output

detection. (Please refer to the User

Guide and SDK Guide for more

information).

The green power LED on the router lights up when a power source is connected.

Connect equipment that requires network access to the Ethernet port of your

router. You can connect one device directly, or several devices using a network

switch. Switch on your power supply and wait 2 minutes for your NetComm

Wireless NWL-15 router to start up.

Autres manuels pour NWL-15

Table des matières

Autres manuels NetComm Routeur réseau

NetComm

NetComm Freshtel NB9 Manuel utilisateur

NetComm

NetComm XBox NF1901ACV Manuel utilisateur

NetComm

NetComm 3G42W-M Manuel utilisateur

NetComm

NetComm NTC-6200-02 Mode d’emploi

NetComm

NetComm NB704 Manuel utilisateur

NetComm

NetComm 3G15Wn Manuel utilisateur

NetComm

NetComm NF5 Manuel utilisateur

NetComm

NetComm G.SHDSL 4-port Security Modem Routers NB712 Manuel utilisateur

NetComm

NetComm NTC-40 series Manuel utilisateur

NetComm

NetComm NB6PLUS4WN Manuel utilisateur

NetComm

NetComm NF2 Manuel d'exploitation

NetComm

NetComm NTC-6200 Manuel utilisateur

NetComm

NetComm NTC-6000 SERIES Manuel utilisateur

NetComm

NetComm V300 Manuel utilisateur

NetComm

NetComm Whitepaper TR-069 Manuel utilisateur

NetComm

NetComm NF8AC Comment utiliser

NetComm

NetComm NP290W Manuel utilisateur

NetComm

NetComm Poe01 Manuel utilisateur

NetComm

NetComm NP2008HS Manuel utilisateur

NetComm

NetComm NF15ACV Manuel utilisateur

NetComm

NetComm NP740n Manuel utilisateur

NetComm

NetComm NTC-40WV Manuel utilisateur

NetComm

NetComm NWL-11 Manuel utilisateur

NetComm

NetComm NB8 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité