Neilsen CT5823 Manuel utilisateur

VAG VW AUDI SKODA SEAT TIMING LOCKING SETTING TOOL

1.2 1.4 1.6 FSI TSI TFSI TDC

CT5823

INSTRUCTION MANUAL

Contents

A Camshaft Locking Tool,

OEM T10414

B Camshaft Alignment Tool

OEM T10171/T10171A

C TDC Indicator

OEM T10170

D Gauge OEM VAS6079

E Cover alignment pins

OEM T10341

F Tensioner pin OEM T40011

G Crankshaft locking pin OEM T10340

GENERAL

Designed to offer an engine timing kit for the 1.2, 1.4 & 1.6 petrol engines found

across the Volkswagen Audi Group range from 2003 to 2015.

The tool kit includes the Dial Test Indicator and adaptor required to accurately

find TDC on the engines listed.

Applications:

Audi: A1 (10-15), A1 Sportback (10-15), A3 Cabriolet (10-13), A3 (10-15),

A3 Sportback (03-13)

Seat: Altea/Altea XL (10-15), Ibiza (10-15), Leon (10-13), Toledo (12-15)

Skoda:Fabia II (10-15), Praktik (10-15), Rapid (12-15), Rapid Sportback

(12-15), Octavia II (04-13), Yeti (09-15), Yeti Outdoor (13-15)

VW:Beetle (11-15), Caddy/Caddy Maxi (10-15), EOS (07-15), Golf V

(03-13), Golf V Estate (07-09), Golf VI (10-13), Golf VI Estate (10-13),

Golf VI Cabriolet (11-15), Golf Plus (05-14), Jetta (05-14), Passat (05-15),

Polo (09-14), Scirocco (08-14), Tiguan (07-15), Touran (03-15)

Engine Codes:

1.2 TFSi: CBZA, CBZB, CBZC

1.4 FSi/TFSi:BLG, BMY, BWK, CAVA, CAVB, CAVC, CAVD, CAVE,

CAVF, CAXA, CAXC, CDGA, CSMA

1.6 FSi:BAG, BLF, BLP

SAFETY INSTRUCTIONS

• Do not use the tool if parts are missing or damaged.

• Use the tool for the intended purpose only.

• Never place the tool on the vehicle battery. There is a risk of a short circuit.

• Be careful when working with the engine running. Loose clothing, tools and

other objects can be caught by rotating parts and cause serious injury.

• Keep children and other unauthorized persons away from the work area.

• Do not allow children to play with the tool or its packaging.

• Be careful when working on hot engines because of the risk of burn injuries.

• If you remove the ignition key before repairing, you can prevent the engine from

being started accidentally and resulting in engine damage.

• This manual serves as a brief guide and does not replace a workshop manual.

Always refer to the vehicle-specific service literature, particularly the technical

data such as torque values and instructions for disassembly/assembly, etc.

• After repair or before starting the engine, turn a minimum of 2 turns by hand and

check the timing again.

• Turn the engine only in the normal direction of rotation (clockwise unless

otherwise specified).

• Do not use locking tools for camshaft and crankshaft as a counter-holder,

during loosening or tightening screws on pulleys, camshafts or crankshafts. This

can damage tools and engine components. Only use tools that are suitable for

this purpose.

INSTRUCTIONS FOR USE

A Camshaft Locking Tool

Camshaft Locking Tool is the camshaft locking tool

used on the 1.2 FSi engines (CBZA and CBZB).

To gain access to the grooved end of the

camshaft remove the hose connecting block

from the rear of the cylinder head (gearbox

end).

Ensure fixing bolt can be fitted.

B Camshaft Alignment Tool

If the Camshaft Timing Marks are not correctly aligned with the engine set at

TDC, turn the Crankshaft 360°and check the Camshaft timing mark again. Fit

the Camshaft Alignment Tool.

If the Camshaft Alignment tool can still not be fitted the valve timing is incorrect.

C TDC Indicator

The Indicator is fitted into the first cylinder spark plug hole. The extension makes

contact with the piston face and as the engine is slowly rotated the DTI indicates

the TDC, or the highest point required.

Many performance engines have an interference combustion area, which if the

correct timing position is not achieved could result in serious damage to the

valves and other parts of the engine.

D Gauge

Top Dead Centre (TDC) measurement must be checked, this set includes TDC

Adaptor (used in conjunction with a Dial Test Indicator) which enables the

accurate measurement of the piston position.

E Cover alignment pins

The two guide pins hold the supercharger in the correct position during

installation. Re-install the sprockets and chain and correctly tighten the

sprockets.

It is advised to use new crankshaft pulley and camshaft sprocket bolts.

Remove the Camshaft Alignment Tool and turn the Crankshaft twice in a

clockwise direction. Check the valve timing again.

F Tensioner pin

Fit the tensioner locking pin to hold the chain tensioner back, allowing the

removal of the camshaft sprockets and chain. Set the camshaft positions and

align using the Camshaft Alignment Tool.

G Crankshaft locking pin

Use the Crankshaft Locking tool when loosening and tightening the crank.

CANNON TOOLS LTD

Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.

www.cannontools.co.uk

Table des matières

Autres manuels Neilsen Outils

Neilsen

Neilsen CT4188 Manuel utilisateur

Neilsen

Neilsen CT1509 Manuel utilisateur

Neilsen

Neilsen CT3073 Manuel utilisateur

Neilsen

Neilsen CT2266 Manuel utilisateur

Neilsen

Neilsen CT2102 Manuel utilisateur

Neilsen

Neilsen CT1057 Manuel utilisateur

Neilsen

Neilsen CT3583 Manuel utilisateur

Neilsen

Neilsen CT4793 Manuel utilisateur

Neilsen

Neilsen CT5202 Manuel utilisateur

Neilsen

Neilsen CT0527 Manuel utilisateur

Neilsen

Neilsen CT4794 Manuel utilisateur

Neilsen

Neilsen CT4694 Manuel utilisateur

Neilsen

Neilsen CT2737 Manuel utilisateur

Neilsen

Neilsen CT4852 Manuel utilisateur

Neilsen

Neilsen CT4621 Manuel utilisateur

Neilsen

Neilsen CT2247 Manuel utilisateur

Neilsen

Neilsen NAH-A30B Manuel utilisateur

Neilsen

Neilsen CT5271 Manuel utilisateur

Neilsen

Neilsen CT0676 Manuel utilisateur

Neilsen

Neilsen CT4448 Instructions de fonctionnement

Neilsen

Neilsen VAG CT5467 Manuel utilisateur

Neilsen

Neilsen CT1535 Manuel utilisateur

Neilsen

Neilsen CT1533 Manuel utilisateur

Neilsen

Neilsen CT0729 Instructions de fonctionnement

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser