National Instruments PXIe-6595 Manuel utilisateur
GETTING STARTED GUIDE
PXIe-6595
32 Gbps, 8-Channel PXI High-Speed Serial Instrument
Note Before you begin, install and configure your chassis and controller.
Note Adapter modules are not installable or interchangeable on the PXIe-6595.
Verifying the System Requirements
To use the PXIe-6595, your system must meet certain requirements. For more information
about minimum system requirements, recommended system, and supported application
development environments (ADEs), refer to the FlexRIO readme, which is available at ni.com/
manuals.
Unpacking the Kit
Notice To prevent electrostatic discharge (ESD) from damaging the module,
ground yourself using a grounding strap or by holding a grounded object, such as
your computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the module from the package and inspect it for loose components or other signs
of damage.
Notice Never touch the exposed pins of connectors.
Note Do not install a module if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the module in the antistatic package when the module is not in use.
PXIe-6595 Kit Contents
The following items are included in the device kit:
• PXIe-6595
•PXIe-6595 Safety, Environmental, and Regulatory Information document
Preparing the Environment
Ensure the environment in which you are using the PXIe-6595 meets the following
specifications.
Operating environment
Ambient temperature range 0 °C to 55 °C1
Relative humidity range 10% to 90%, noncondensing
Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient
temperature)
Pollution Degree 2
Indoor use only.
Note For complete specifications, refer to the specifications document for your
device at ni.com/manuals.
Installing the PXIe-6595
Notice To prevent damage to the PXIe-6595 caused by ESD or contamination,
handle the module using the edges or the metal bracket.
1. Ensure the AC power source is connected to the chassis before installing the module.
The AC power cord grounds the chassis and protects it from electrical damage while you
install the module.
2. Power off the chassis.
3. Inspect the slot pins on the chassis backplane for any bends or damage prior to
installation. Do not install a module if the backplane is damaged.
4. Remove the black plastic covers from all the captive screws on the module front panel.
5. Identify a supported slot in the chassis. The following figure shows the symbols that
indicate the slot types.
1The PXIe-6595 requires a chassis with slot cooling capacity ≥58 W. Not all chassis with slot
cooling capacity ≥58 W can achieve this ambient temperature range. Refer to the PXI Chassis
Manual for specifications to determine the ambient temperature ranges your chassis can achieve.
2| ni.com | PXIe-6595 Getting Started Guide
Figure 1. Chassis Compatibility Symbols
NI PXIe-1062Q
12 3 45
1. PXI Express System Controller Slot
2. PXI Peripheral Slot
3. PXI Express Hybrid Peripheral Slot
4. PXI Express System Timing Slot
5. PXI Express Peripheral Slot
PXIe-6595 modules can be placed in PXI Express peripheral slots, PXI Express hybrid
peripheral slots, or PXI Express system timing slots.
6. Touch any metal part of the chassis to discharge static electricity.
7. Ensure that the ejector handle is in the downward (unlatched) position.
8. Place the module edges into the module guides at the top and bottom of the chassis. Slide
the module into the slot until it is fully inserted.
Figure 2. Module Installation
2
3
NI PXIe-1075
1
1. Chassis
2. Hardware Module
3. Ejector Handle in Downward (Unlatched) Position
9. Latch the module in place by pulling up on the ejector handle.
10. Secure the module front panel to the chassis using the front-panel mounting screws.
Note Tightening the top and bottom mounting screws increases mechanical
stability and also electrically connects the front panel to the chassis, which can
improve the signal quality and electromagnetic performance.
PXIe-6595 Getting Started Guide | © National Instruments Corporation | 3
11. Cover all empty slots using either filler panels (standard or EMC) or slot blockers with
filler panels, depending on your application.
Note For more information about installing slot blockers and filler panels, go
to ni.com/r/pxiblocker.
12. Power on the chassis.
Configuring the PXIe-6595 in MAX
Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX
informs other programs about which NI hardware products are in the system and how they are
configured. MAX is automatically installed with FlexRIO.
1. Launch MAX.
2. In the configuration tree, expand Devices and Interfaces to see the list of installed NI
hardware.
Installed modules appear under the name of their associated chassis.
3. Expand your Chassis tree item.
MAX lists all modules installed in the chassis. Your default names may vary.
Note If you do not see your module listed, press <F5> to refresh the list of
installed modules. If the module is still not listed, power off the system, ensure
the module is correctly installed, and restart.
4. Record the identifier MAX assigns to the hardware. Use this identifier when
programming the PXIe-6595.
5. Self-test the hardware by selecting the item in the configuration tree and clicking Self-
Test in the MAX toolbar.
The MAX self-test performs a basic verification of hardware resources.
NI Services
Visit ni.com/support to find support resources including documentation, downloads, and
troubleshooting and application development self-help such as tutorials and examples.
Visit ni.com/services to learn about NI service offerings such as calibration options, repair, and
replacement.
Visit ni.com/register to register your NI product. Product registration facilitates technical
support and ensures that you receive important information updates from NI.
NI corporate headquarters is located at 11500 N Mopac Expwy, Austin, TX, 78759-3504,
USA.
4| ni.com | PXIe-6595 Getting Started Guide
PXIe-6595 Getting Started Guide | © National Instruments Corporation | 5
Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for
information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their
respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your
software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find
information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer
to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how
to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS
TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.
Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable
limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
© 2020 National Instruments Corporation. All rights reserved.
378313A-01 September 29, 2020
Table des matières
Autres manuels National Instruments Unité de contrôle
National Instruments
National Instruments FieldPoint FP-20 Series Manuel utilisateur
National Instruments
National Instruments Module SCXI-1503 Manuel
National Instruments
National Instruments NI 9930 Manuel utilisateur
National Instruments
National Instruments NI DCM-2316 Manuel utilisateur
National Instruments
National Instruments SCC-FV01 Manuel utilisateur
National Instruments
National Instruments 5174 Manuel utilisateur
National Instruments
National Instruments NI 9227 Manuel utilisateur
National Instruments
National Instruments NI R Series Manuel utilisateur
National Instruments
National Instruments NI 9375 Manuel utilisateur
National Instruments
National Instruments FBUS-HSE/H1 LD Manuel utilisateur
National Instruments
National Instruments NI 9478 Manuel utilisateur
National Instruments
National Instruments PXI-6682 Series Manuel utilisateur
National Instruments
National Instruments NI PXIe-7976R Manuel utilisateur
National Instruments
National Instruments NI 9203 Manuel
National Instruments
National Instruments SCXI-1112 Manuel utilisateur
National Instruments
National Instruments SCC-PWR02 Manuel utilisateur
National Instruments
National Instruments FIeldPoint FP-AO-200 Manuel utilisateur
National Instruments
National Instruments 6589 Manuel utilisateur
National Instruments
National Instruments PXIe-4322 Manuel utilisateur
National Instruments
National Instruments 6587 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
