National Instruments PXIe-8108 Manuel utilisateur

INSTALLATION GUIDE

NI PXIe-8108

This document contains information about installing the NI PXIe-8108

controller in a PXI Express chassis. For complete configuration and

troubleshooting information (including information about BIOS setup,

adding RAM, etc.), refer to the NI PXIe-8108 User Manual. The manual is

in PDF format on the documentation CD included with the controller and

on the National Instruments Web site, ni.com.

Installing the NI PXIe-8108

This section contains general installation instructions for the

NI PXIe-8108. Consult the NI PXIe-8108 User Manual for specific

instructions and warnings.

1. Plug in the chassis before installing the NI PXIe-8108. The power cord

grounds the chassis and protects it from electrical damage while you

install the module. Make sure the power switch is turned off.

Cautions In some National Instruments chassis, such as the NI PXI-1062Q, you must

ensure that the power LED is off. For more information about chassis power behavior, refer

to the user manual for the specific chassis.

To protect both yourself and the chassis from electrical hazards, leave the chassis off until

you finish installing the NI PXIe-8108 module.

2. Remove any panels blocking access to the system controller slot

(slot 1) in the chassis.

3. Touch the metal part of the case to discharge any static electricity that

might be on your clothes or body.

4. Remove the protective plastic covers from the four bracket-retaining

screws as shown in Figure 1.

NI PXIe-8108 Installation Guide 2 ni.com

Figure 1. Removing Protective Screw Caps

5. Make sure the injector/ejector handle is in its downward position.

Align the NI PXIe-8108 with the card guides on the top and bottom

of the system controller slot.

Caution Do not raise the injector/ejector handle as you insert the NI PXIe-8108. The

module will not insert properly unless the handle is in its downward position so that it does

not interfere with the injector rail on the chassis.

6. Hold the handle as you slowly slide the module into the chassis until

the handle catches on the injector/ejector rail.

7. Raise the injector/ejector handle until the module firmly seats into the

backplane receptacle connectors. The front panel of the NI PXIe-8108

should be even with the front panel of the chassis.

8. Tighten the four bracket-retaining screws on the top and bottom of the

front panel to secure the NI PXIe-8108 to the chassis.

9. Check the installation.

10. Connect the keyboard and mouse to the appropriate connectors. If you

are using a PS/2 keyboard and a PS/2 mouse, a Y-splitter adapter is

available to connect both to a single USB connector. National

Instruments offers a Y-splitter adapter cable, part number 778713-02,

available through the online catalog at ni.com/products.

11. Connect the DVI-I monitor video cable to the DVI-I connector, or use

the DVI-to-VGA adapter included with your controller to connect a

VGA monitor to the DVI-I connector.

12. Connect peripherals to ports as required by your system configuration.

13. Power on the display. Refer to the NI PXIe-8108 User Manual for

details.

1 Protective Screw Cap (4X)

©National Instruments Corporation 3 NI PXIe-8108 Installation Guide

14. Power on the chassis.

15. Verify that the controller boots. If it does not boot, refer to the What If

the NI PXIe-8108 Does Not Boot? section later in this guide.

Figure 2 shows an NI PXIe-8108 controller installed in the system

controller slot of a National Instruments PXIe-1062Q chassis.

Figure 2. NI PXIe-8108 Installed in a PXI Express Chassis

How to Remove the Controller from the PXI Express Chassis

The NI PXIe-8108 controller is designed for easy handling. To remove the

unit from the PXI Express chassis:

1. Power off the chassis.

2. Remove any cables that may be attached to the controller front panel.

3. Unscrew the 4 bracket-retaining screws in the front panel.

4. Press the injector/ejector handle down.

5. Slide the unit out of the chassis.

What If the NI PXIe-8108 Does Not Boot?

Several problems can cause a controller not to boot. Here are some things

to look for and possible solutions.

Things to Notice

• Which LEDs come on? The Power OK LED should stay lit. The

Drive LED should blink during boot as the disk is accessed.

• What appears on the display? Does it hang at some particular point

(BIOS, Operating System, etc.)? If nothing appears on the screen, try

a different monitor. Does your monitor work with a different PC? If it

1 NI PXIe-1062Q Chassis

2 NI PXIe-8108 Controller

3 Injector/Ejector Rail

NI PXIe-1062Q

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.

Refer to the Terms of Use section on ni.com/legal for more information about National

Instruments trademarks. Other product and company names mentioned herein are trademarks or trade

names of their respective companies. For patents covering National Instruments products/technology,

refer to the appropriate location: Help»Patents in your software, the patents.txt file on your

media, or the National Instruments Patent Notice at ni.com/patents.

hangs, note the last screen output that you saw for reference when

consulting National Instruments technical support.

• What has changed about the system? Did you recently move the

system? Was there electrical storm activity? Did you recently add a

new module, memory chip, or piece of software?

Things to Try

• Make sure the chassis is plugged in to a working power source.

• Check any fuses or circuit breakers in the chassis or other power

supply (possibly an uninterruptible power supply).

• Make sure the controller module is firmly seated in the chassis.

• Remove all other modules from the chassis.

• Remove any nonessential cables or devices.

• Try the controller in a different chassis or a similar controller in this

same chassis.

• Clear the CMOS. (Refer to the System CMOS section of the

NI PXIe-8108 User Manual.)

• Recover the hard drive on the controller. (Refer to the Hard Drive

Recovery section of the NI PXIe-8108 User Manual.)

For more troubleshooting information, refer to the NI PXIe-8108 User

Manual. The manual is in PDF format on the documentation CD included

with your controller and on the National Instruments Web site, ni.com.

What If I Can’t See the Video?

This problem usually results from having the video card output set past the

limits of the monitor. You will need to boot Windows in Safe Mode. To do

this, reboot the controller. As Windows begins to boot, hold down <F8>.

You should now be able to reset the video driver to lower settings. Try

setting the resolution to 640 × 480 and the refresh rate to 60 Hz. Once you

reboot, you can raise these values again, using the test option in Windows.

These settings are accessible through the Advanced tab of the Display item

in the Control Panel. Alternately, you can try a different monitor,

preferably a newer and larger one.

If the system has been booted to Windows without a monitor attached, the

driver may have defaulted to the video output connector being disabled.

Press <Ctrl-Alt-F1> to re-enable the video display in Windows. Press

<Ctrl-Alt-F4> to re-enable a DVI display. For more information, refer to

KnowledgeBase 3OHCFRD8 at ni.com/support.

Table des matières

Autres manuels National Instruments Matériel informatique

National Instruments

National Instruments NI-488.2M Manuel utilisateur

National Instruments

National Instruments cFP-20xx Manuel utilisateur

National Instruments

National Instruments R Series Manuel utilisateur

National Instruments

National Instruments 6008 Manuel utilisateur

National Instruments

National Instruments CAN PXI-846 Series Manuel utilisateur

National Instruments

National Instruments PCI-6528 Manuel utilisateur

National Instruments

National Instruments PC-LPM-16/PnP Manuel utilisateur

National Instruments

National Instruments PXI Express PXIe-1075 Manuel utilisateur

National Instruments

National Instruments NI PXI-8221 Manuel utilisateur

National Instruments

National Instruments GPIB-1014 Series Manuel utilisateur

National Instruments

National Instruments NAT7210 Manuel utilisateur

National Instruments

National Instruments 8330 Series Manuel utilisateur

National Instruments

National Instruments NI-9252 Manuel

National Instruments

National Instruments NI PXIe-1082 Manuel utilisateur

National Instruments

National Instruments PXI-GPIB Manuel utilisateur

National Instruments

National Instruments GPIB-1014 Series Manuel utilisateur

National Instruments

National Instruments PC-DIO-24/PnP Manuel utilisateur

National Instruments

National Instruments NI 6612 Manuel utilisateur

National Instruments

National Instruments MXI-2 Manuel utilisateur

National Instruments

National Instruments 9260 Manuel utilisateur

National Instruments

National Instruments PC/104-GPIB Manuel utilisateur

National Instruments

National Instruments PXI NI 8171 Series Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

National Instruments

National Instruments GPIB Series Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur