National Instruments 6008 Manuel utilisateur

USER GUIDE AND SPECIFICATIONS

NI USB-6008/6009

This guide describes how to use the National Instruments USB-6008/6009

data acquisition (DAQ) devices and lists specifications.

Introduction

The NI USB-6008/6009 provides connection to eight analog input (AI)

channels, two analog output (AO) channels, 12 digital input/output (DIO)

channels, and a 32-bit counter with a full-speed USB interface.

Note This manual revision updates naming conventions to reflect the conventions used in

NI-DAQmx. Table 1 notes the correlation between the old and updated names.

Table 1. Digital Output Driver Type Naming Conventions

Hardware Functionality NI-DAQmx Terminology

Open-drain Open collector

Push-pull Active drive

NI USB-6008/6009 User Guide and Specifications 2 ni.com

Figure 1. NI USB-6008/6009

Figure 2. NI USB-6008/6009 Back View

Table 2. Differences Between the NI USB-6008 and NI USB-6009

Feature NI USB-6008 NI USB-6009

AI Resolution 12 bits differential,

11 bits single-ended

14 bits differential,

13 bits single-ended

Maximum AI Sample Rate,

Single Channel*

10 kS/s 48 kS/s

Maximum AI Sample Rate,

Multiple Channels (Aggregate)*

10 kS/s 48 kS/s

DIO Configuration Open collector Open collector or active drive

*System dependent.

1 USB Cable Strain Relief

NI USB-6009

8 Inputs, 14-bit, Multifunction I/O

32 Digital 17

1 Analog 16

©National Instruments Corporation 3 NI USB-6008/6009 User Guide and Specifications

Safety Guidelines

Caution Operate the hardware only as described in these operating instructions.

The following section contains important safety information that you must

follow when installing and using the NI USB-6008/6009.

Do not operate the NI USB-6008/6009 in a manner not specified in this

document. Misuse of the device can result in a hazard. You can compromise

the safety protection built into the device if the device is damaged in any

way. If the device is damaged, contact National Instruments for repair.

Do not substitute parts or modify the device except as described in this

document. Use the device only with the chassis, modules, accessories, and

cables specified in the installation instructions. You must have all covers

and filler panels installed during operation of the device.

Do not operate the device in an explosive atmosphere or where there may

be flammable gases or fumes. If you must operate the device in such an

environment, it must be in a suitably rated enclosure.

If you need to clean the device, use a dry cloth. Make sure that the device

is completely dry and free from contaminants before returning it to service.

Operate the device only at or below Pollution Degree 2. Pollution is foreign

matter in a solid, liquid, or gaseous state that can reduce dielectric strength

or surface resistivity. The following is a description of pollution degrees:

• Pollution Degree 1 means no pollution or only dry, nonconductive

pollution occurs. The pollution has no influence.

• Pollution Degree 2 means that only nonconductive pollution occurs in

most cases. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

• Pollution Degree 3 means that conductive pollution occurs, or dry,

nonconductive pollution occurs that becomes conductive due to

condensation.

You must insulate signal connections for the maximum voltage for which

the device is rated. Do not exceed the maximum ratings for the device. Do

not install wiring while the device is live with electrical signals. Do not

remove or add connector blocks when power is connected to the system.

Avoid contact between your body and the connector block signal when hot

swapping modules. Remove power from signal lines before connecting

them to or disconnecting them from the device.

NI USB-6008/6009 User Guide and Specifications 4 ni.com

Operate the device at or below the Measurement Category I1. Measurement

circuits are subjected to working voltages2and transient stresses

(overvoltage) from the circuit to which they are connected during

measurement or test. Measurement categories establish standard impulse

withstand voltage levels that commonly occur in electrical distribution

systems. The following is a description of measurement categories:

• Measurement Category I is for measurements performed on circuits

not directly connected to the electrical distribution system referred to

as MAINS3voltage. This category is for measurements of voltages

from specially protected secondary circuits. Such voltage

measurements include signal levels, special equipment, limited-energy

parts of equipment, circuits powered by regulated low-voltage sources,

and electronics.

• Measurement Category II is for measurements performed on circuits

directly connected to the electrical distribution system. This category

refers to local-level electrical distribution, such as that provided by a

standard wall outlet (for example, 115 V for U.S. or 230 V for Europe).

Examples of Measurement Category II are measurements performed

on household appliances, portable tools, and similar E Series devices.

• Measurement Category III is for measurements performed in the

building installation at the distribution level. This category refers to

measurements on hard-wired equipment such as equipment in fixed

installations, distribution boards, and circuit breakers. Other examples

are wiring, including cables, bus-bars, junction boxes, switches,

socket-outlets in the fixed installation, and stationary motors with

permanent connections to fixed installations.

• Measurement Category IV is for measurements performed at the

primary electrical supply installation (<1,000 V). Examples include

electricity meters and measurements on primary overcurrent

protection devices and on ripple control units.

1 Measurement Category as defined in electrical safety standard IEC 61010-1. Measurement Category is also referred to as

Installation Category.

2 Working Voltage is the highest rms value of an AC or DC voltage that can occur across any particular insulation.

3 MAINS is defined as a hazardous live electrical supply system that powers equipment. Suitably rated measuring circuits may

be connected to the MAINS for measuring purposes.

©National Instruments Corporation 5 NI USB-6008/6009 User Guide and Specifications

Software

Software support for the NI USB-6008/6009 for Windows 2000/XP/Vista

is provided by NI-DAQmx.

The NI-DAQmx CD contains example programs that you can use to get

started programming with the NI USB-6008/6009. Refer to the NI-DAQmx

for USB Devices Getting Started Guide, that shipped with your device and

is also accessible from Start»All Programs»National Instruments»

NI-DAQ for more information.

Note For information about non-Windows operating system support, refer to

ni.com/info and enter rddqld.

LabVIEW SignalExpress for DAQ

The NI-DAQmx CD includes LabVIEW SignalExpress for DAQ which is

an interactive, measurement software tool for quickly acquiring, analyzing,

and presenting data with no programming required. The application is

available at Start»All Programs»National Instruments»NI DAQ»

LabVIEW SignalExpress.

NI USB-6008/6009 User Guide and Specifications 6 ni.com

Hardware

The following block diagram shows key functional components of the

NI USB-6008/6009.

Figure 3. Device Block Diagram

P1.<0..3>

P0.<0..7>

Digital I/O Terminal Block

AI <0..7>

AO 0

AO 1

Analog I/O Terminal Block

+2.5 V/CAL

+5 V/200 mA

8 Channel

12/14b ADC

12b DAC

USB Microcontroller

SPI

External

Power

Supply

Vbus

Full-Speed USB Interface

USB

PFI 0

©National Instruments Corporation 7 NI USB-6008/6009 User Guide and Specifications

Setting Up Hardware

Complete the following steps to set up the hardware:

1. Install combicon screw terminal blocks by inserting them into the

combicon jacks.

2. Figure 4 illustrates the signal labels that ship in the NI USB-6008/6009

kit. You can apply the signal labels to the screw terminal blocks for

easy signal identification.

Figure 4. NI USB-6008/6009 Signal Labels

3. Refer to Table 3 and Figures 4 and 5 for signal label orientation and

affix the provided signal labels to the screw terminal blocks. Until the

signal labels are applied, you can insert the screw terminal blocks into

either of the combicon jacks.

1 Terminal Number Labels (Use Both Together)

2 Digital I/O Label

3 Single-Ended Label (Use Either)

4 Differential Label (Use Either)

ANALOG DIGITAL

NI USB-6008/6009 User Guide and Specifications 8 ni.com

Figure 5. Signal Label Application Diagram

Note Once you label the screw terminal blocks, you must only insert them into the

matching combicon jack, as indicated by the overlay label on the NI USB-6008/6009

device.

4. Connect the wiring to the appropriate screw terminals.

1 Overlay Label with Pin Orientation Guides

2 Combicon Jack

3 Signal Labels

4 USB Cable

9006-BSUIN

Inoi

cnufitluM

,tib-41,stupnI8

23 latigiD 71

1golanA 6

©National Instruments Corporation 9 NI USB-6008/6009 User Guide and Specifications

I/O Connector

The NI USB-6008/6009 ships with one detachable screw terminal block for

analog signals and one detachable screw terminal block for digital signals.

These terminal blocks provide 16 connections that use 16 AWG to

28 AWG wire.

Table 3 lists the analog terminal assignments, and Table 4 lists the digital

terminal assignments.

Table 3. Analog Terminal Assignments

Module Terminal

Signal,

Single-Ended Mode

Signal,

Differential Mode

1GND GND

2AI 0 AI 0+

3AI 4 AI 0–

4GND GND

5AI 1 AI 1+

6AI 5 AI 1–

7GND GND

8AI 2 AI 2+

9AI 6 AI 2–

10 GND GND

11 AI 3 AI 3+

12 AI 7 AI 3–

13 GND GND

14 AO 0 AO 0

15 AO 1 AO 1

16 GND GND

12345678910111213141516

NI USB-6008/6009 User Guide and Specifications 10 ni.com

Table 4. Digital Terminal Assignments

Module Terminal Signal

17 P0.0

18 P0.1

19 P0.2

20 P0.3

21 P0.4

22 P0.5

23 P0 6

24 P0.7

25 P1.0

26 P1.1

27 P1.2

28 P1.3

29 PFI 0

30 +2.5 V

31 +5 V

32 GND

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels National Instruments Matériel informatique

National Instruments

National Instruments NI 9403 Manuel utilisateur

National Instruments

National Instruments PCIe-1437 Manuel utilisateur

National Instruments

National Instruments DAQ X NI 634 Series Manuel utilisateur

National Instruments

National Instruments PXI Express PXIe-1075 Manuel utilisateur

National Instruments

National Instruments NI PXIe-8133 Manuel utilisateur

National Instruments

National Instruments NI 54 Series Manuel

National Instruments

National Instruments PXIe-8108 Manuel utilisateur

National Instruments

National Instruments NAT7210 Manuel utilisateur

National Instruments

National Instruments Texas Instruments 6711 DSK Manuel utilisateur

National Instruments

National Instruments PXIe-8106 Manuel utilisateur

National Instruments

National Instruments NI-9146 Manuel du propriétaire

National Instruments

National Instruments PXI Express NI PXIe-1065 Manuel utilisateur

National Instruments

National Instruments NI PXI-8221 Manuel utilisateur

National Instruments

National Instruments CAN Series Manuel utilisateur

National Instruments

National Instruments PC-LPM-16/PnP Manuel utilisateur

National Instruments

National Instruments 9260 Manuel utilisateur

National Instruments

National Instruments PXIe-8240 Manuel utilisateur

National Instruments

National Instruments NI PXIe-8105 Manuel utilisateur

National Instruments

National Instruments PXI-8101 Manuel utilisateur

National Instruments

National Instruments PXI-8196 Manuel utilisateur

National Instruments

National Instruments PXI-8110 Manuel utilisateur

National Instruments

National Instruments GPIB Series Manuel utilisateur

National Instruments

National Instruments NI roboRIO Manuel utilisateur

National Instruments

National Instruments GPIB-1014 Series Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur