National Instruments FieldPoint cFP-1808 Manuel utilisateur

Quick Start Guide

FieldPoint cFP-21xx

What You Need to Get Set Up

•cFP-21xx LabVIEW RT controller

• Mounting hardware (DIN rail,

panel-mount, or rack-mount

accessory)

• I/O module(s)

•cFP-BP-xbackplane, connector

blocks, cables

• 11–30 VDC power supply

• Accessories: Ethernet cable,

number 2 Phillips screwdriver

• PC running Windows

• FieldPoint software 4.1.1 or later

• LabVIEW Real-Time Module

™

cFP-21xx Quick Start Guide 2 ni.com

1. Mount the Compact FieldPoint Backplane

You can mount the cFP-BP-xbackplane on a 35mm DIN rail, on a panel, or in a

standard 19 in. rack. Before using any of these mounting methods, record the serial

number from the back of the backplane.

Each set of mounting instructions in this document includes an instruction to

connect the protective earth (PE) ground terminal on the cFP-BP-xbackplane to

the system safety ground. The backplane PE ground terminal has the following

symbol stamped beside it: . Connect the backplane PE ground terminal to the

system safety ground using 14 AWG (1.6 mm) wire with a ring lug. Use the

5/16 in. panhead screw shipped with the backplane to secure the ring lug to the

backplane PE ground terminal.

Caution Keep in mind these requirements for space and cabling

clearance:

• Allow at least 51 mm (2 in.) all around the backplane for air

circulation.

• Allow 38 mm (1.5 in.) below and 51 mm (2 in.) above the controller.

Caution If you are using UL Recognized I\O modules with the Compact

FieldPoint system, you must install the entire system in a suitably rated,

UL Listed NEMA or IP enclosure.

Cabling Clearance Cooling Outline 51 mm (2 in.) All Around

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

127 mm

(5.00 in.)

Min. 165 mm

(6.50 in.)

Cabling

Clearance

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

Cooling Outline 51 mm (2 in.) Cooling Outline 51 mm (2 in.)

Min. 182 mm (7.18 in.)

106 mm (4.18 in.)

cFP-21xx Quick Start Guide 4 ni.com

Caution NI recommends that you use one of the mounting systems

described in this document. If you decide to use a custom mounting

solution, make sure that the screws you use are short enough to fit in the

holes in the backplane. The screw holes are 5 mm (0.2 in.) deep.

Mounting the Backplane on a Panel

1. Fasten the panel-mount plates to the back of the cFP-BP-xusing a

number 2 Phillips screwdriver and the 8-32 ×5/16 in. countersink screws

shipped with the kit.

Caution Do not use screws longer than 5/16 in. to fasten the

panel-mount plates to the backplane.

NATIONAL

INSTRUMENTS

102 mm

(4 in.)

457 mm (18 in.)

cFP-21xx Quick Start Guide 6 ni.com

104.78 mm

(4.1 in.)

63.50 mm

(2.5 in.)

22.23 mm

(0.9 in.)

33.15 mm

(1.3 in.)

129.54 mm

(5.1 in.)

311.40 mm

(12.3 in.)

387.60 mm

(15.3 in.)

407.80 mm

(16.1 in.)

127.00 mm

(5.0 in.)

440.94 mm

(17.4 in.)

260 mm (10.25 in.)

102 mm

(4 in.)

2. Bolt or screw the panel-mount accessory to a panel.

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

panel.

Mounting the Backplane on a DIN Rail

NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting or

rack mounting for the cFP-BP-8. The DIN rail mounting kit is NI part number

778614-01.

1. Fasten the DIN rail clip to the cFP-BP-4 using a number 2 Phillips screwdriver

and the 8-32 ×5/16 in. countersink screws shipped with the clip.

104.74 mm

(4.1 in.)

63.46 mm

(2.5 in.)

127.00 mm

(5.0 in.)

22.19 mm

(0.9 in.)

34.04 mm

(1.3 in.)

84.84 mm

(3.3 in.)

161.04 mm

(6.3 in.)

211.84 mm

(8.3 in.)

245.87 mm

(9.6 in.)

cFP-21xx Quick Start Guide 8 ni.com

Caution Do not use screws longer than 5/16 in. to fasten the DIN rail

clip to the backplane.

2. Insert one edge of the DIN rail into the deeper opening of the DIN rail clip.

3. Press down firmly on the backplane to compress the spring until the clip locks

in place on the DIN rail.

4. Connect the PE ground terminal on the cFP-BP-4 to safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

NATIONAL

INSTRUMENTS

Mounting the Backplane in a Standard 19 in. Rack

1. Fasten the rack-mount bracket to the back of the cFP-BP-xusing the captive

screws on the bracket.

2. Bolt the rack-mount accessory to a standard 19 in. rack.

NATIONAL

INSTRUMENTS

cFP-21xx Quick Start Guide 10 ni.com

3. Connect the PE ground terminal on the cFP-BP-xto safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

NATIONAL

INSTRUMENTS

Autres manuels pour FieldPoint cFP-1808

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels National Instruments Matériel informatique

National Instruments

National Instruments PXIe-8115 Manuel utilisateur

National Instruments

National Instruments PCMCIA-232 Manuel utilisateur

National Instruments

National Instruments GPIB-PCIIB Manuel utilisateur

National Instruments

National Instruments MXI-2 Manuel utilisateur

National Instruments

National Instruments CAN Series Manuel utilisateur

National Instruments

National Instruments NI PXIe-8133 Manuel utilisateur

National Instruments

National Instruments GPIB-1014 Series Manuel utilisateur

National Instruments

National Instruments PCI-6034E Manuel utilisateur

National Instruments

National Instruments USRP-2940 Manuel utilisateur

National Instruments

National Instruments Compact FieldPoint Mounting Accessories... Manuel utilisateur

National Instruments

National Instruments cFP-20xx Manuel utilisateur

National Instruments

National Instruments 8330 Series Manuel utilisateur

National Instruments

National Instruments PXI-8110 Manuel utilisateur

National Instruments

National Instruments NI roboRIO Manuel utilisateur

National Instruments

National Instruments MXIbus VME-AT2000 Manuel utilisateur

National Instruments

National Instruments NI 9213 Manuel utilisateur

National Instruments

National Instruments PXIe-4468 Manuel

National Instruments

National Instruments BNC-208 Series Manuel utilisateur

National Instruments

National Instruments VXI-AT2000 Manuel utilisateur

National Instruments

National Instruments CPCI-GPIB Manuel utilisateur

National Instruments

National Instruments NI-9146 Manuel du propriétaire

National Instruments

National Instruments AT-GPIB/TNT Manuel utilisateur

National Instruments

National Instruments DAQPad-6020E Manuel utilisateur

National Instruments

National Instruments SET-2090 Manuel de la liste des pièces

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur