Munters WF54 Manuel utilisateur

*Patents Pending

Instruction Manual

WF54 Tilt Wall Fan with Munters Drive

54” Tilt Wall Exhaust Fan

Models: WF54DTxxCXP-Hx • WF54DTxxCXJ-Hx

WF54

54” Tilt Fan with

Munters Drive*

QM1224r3

WF54 Tilt Fan with Munters Drive

Manual for use and Maintenance

Thank You:

Thank you for purchasing a Munters WF54 tilt fan with Munters Drive. Munters equipment is designed to be the

highest performing, highest quality equipment you can buy. With the proper installation and maintenance it will

provide many years of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be installed

and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation

or maintenance shall not be considered a defect under the Warranty.

Index

Chapters Page

1. Unpacking the Equipment 3

1.1 Parts List 3

1.2 Fan Dimensions 5

2. Installation Instructions 6

2.1 Fan Installation 6

2.2 Shutter Installation 8

3. Electrical Wiring

3.1 Recommended Wire Routing 9

3.2 Electrical Wiring 10

4. Operation and Maintenance 16

4.1 Operation 16

4.2 Maintenenace 16

5. Troubleshooting 17

6. Winterizing 18

6.1 Winterizing 18

6.2 Winter Weather Protection 18

7. Exploded View and Parts List 19

QM1224r3

1.1 Parts List

Unpacking the Equipment

[A]

[B]

[C]

[D]

[E]

[F]

[G]

Each Crate includes:

1 – 54" Belt Drive Fan

4 – Cone Sections ( 2 side, 2 top/bottom)

4 – Support Brackets, galvanized

1 – Cone Guard

1 – Shutter

1 – Hardware Package HP1116 for GCX

HP1116 for 54GCX

[A]…..16 - ¼” x 1½” Lag Screws, ZP

[B]…..26 - ¼” x ½” Flange Head Bolts, ZP

[C]…..4 - ¼” x ¾” Flange Head Bolts, ZP

[D]…..10 - ¼” x 1¾” Flange Head Bolts, ZP

[E]…..40 - ¼” Flange Nuts, ZP

[F]…..8 - ¼” x ¾” TEK Screws, ZP

[G].....10 - ¾” O.D. x 1”L. Spacers

Discharge cone is designed to mount on fan outlet for increased airow and to support the

exhaust guard. A shutter or guard must be mounted on the fan inlet.

NOTE:

Before beginning installation, check the overall condition of the equipment. Remove packing materials, and examine all

components for signs of shipping damage. Any shipping damage is the customer’s responsibility and should be reported

immediately to your freight carrier. Fan is shipped complete with all accessories. Remove shutter, guard and cone sections

before proceeding with installation.

Cat. No. Cone Type A B C

Below F.O.

D E F G

Cone Height

Cone Width

Wall Openings

(W.O.)

WF54 54GCX 651⁄4” 631⁄4” 125⁄8” 56” 58” 225⁄8” 66” 59” 561⁄2”W. x 621⁄2”H.

Dimensions:

Unpacking the EquipmentChapter 1

Wall Opening (W.O.)

1.2 Fan Dimentions E

Wall Opening (W.O)

H - Cone Width

Shutter

G - Cone Height

Fan Specifications: 60Hz shown (50Hz available)

Power: 230VAC or 230/460 VAC

Phase: 1 or 3

QM1224r3

2.1 Fan Installation

Step 1

Construct framed opening to correct size according to the Wall Opening

listed in chart below. See Figure 1A, 1B,1C and 1D.

Installation Instructions 2.

Figure 1A

Ceiling

Framing

(see chart A)

12"

(see chart A)

See minimum spac-

ing notes in Chart A Z

NOTE:

Chart A

2 x 4 framing

56½"W. x 62½"H.

Catalog No.

WF54

Concrete framing

56½"W. x 64"H.

Figure 1B

2 x 4 Framing

Figure 1C

Concrete Framing

Figure 1D

Greater than 4” Wall Thickness

B - Concrete Wall Opening

A - 2 x 4 Wall Opening

2 x 4

Framing cut

at 12° to

match fan

housing

3½"

Fan with Discharge Cone:

a minimum clearance

of 12” on all sides is

recommended, but fans

may be installed with less

clearance if required. The

minimum center-to-center

distance is 60”.

Step 2

Slide fan assembly into framed wall opening from outside

of the building. Insert top of fan into opening and hold fan

against top frame. Midpoint of top panel must be aligned

with frameing for bottom flange of fan to pass through

opening. See Figure 2. Secure top and bottom flanges to

wall using (6) Screws [A]. See Figure 3A.

Step 3

Left and right flanges must be bent outward over framing.

This can be done by hand or with a rubber mallet. Be

careful to bend along perforation and not to distort the

housing. See Figure 3B.

Step 4

Confirm that housing inside dimensions match those shown

in Figure 4A. Then secure left and right flanges to wall

using (10) Screws [A] (provided). See Figure 4B & 4C.

Step 5

Outlet of fan comes unguarded, install discharge cone

with guard on outlet of fan at this time. Refer to QM1049

for flat sided cone installation instructions.

Figure 2

Installation InstructionsChapter 2

Figure 3A

Figure 3B

601⁄2”

Figure 4A

¼" x 1½ " Lag

screws [A]

Step 6

Make electrical connections to fan motor per instructions provided with fan or as shown on motor.

See Wiring Section on page 9.

NOTE:

This is NOT the Wall

Opening size.

56”

QM1224r3

Figure 4B Figure 4C

¼" x 1½" Lag

screws [A]

Installation InstructionsChapter 2

Figure 5A Figure 5B

Bottom

Shutter Clip

Step 1

Insert shutter into fan by sliding the bottom flange of shutter into bottom shutter clips and pressing shutter

inward, See Figure 5A. Fasten shutter in place by rotating the side and top shutter clips over the shutter

flanges, See Figure 5B.

Top

Shutter

Clip

Side Shutter Clip

2.2 Shutter Installation

3.1 Recommended Wire Routing

Electrical Wiring 3.

Option 1 -

Step 1

The Munters Drive fan comes with a coil of electrical

cables that is pre-wired to the motor. Find the end of

the cable and form a drip loop and then run the cable

through the side of the fan housing, through flexible

conduit and into building. See Figure 6A & 6B.

Step 2

Add flashing and/or caulk around completed housing

on exterior side of building wall.

Option 2 -

Step 1

The Munters Drive fan comes with a coil of electrical

cables that is pre-wired to the motor. Find the end of the cable and form a drip loop and then run the cable

through housing and frame into wall cavity and into the building. See Figure 7A & 7B.

Step 2

Add flashing and/or caulk around completed housing on exterior side of building wall.

Drip

Loop

Figure 6B

Figure 7A

Figure 7B

Drip

Loop

Drip

Loop

2”

QM1224r3

Electrical WiringChapter 3

Recommended Lightning Protection

FC2003, 230V, 1 Phase

240 VAC

Power Supply for Fan

240 VAC

Power Out to Fan

Single Phase

Figure 8A

Safety Cut-Off Switch

Three Phase

Power Out to Fan Motor

Three Phase

Power Supply for Fan

Safety Cut-Off Switch

Three Phase

Figure 8B

Recommended Lightning Protection

FC2006, 230V, 3 Phase

FC2009, 460V, 3 Phase

All wiring should be installed in accordance with National, State, and Local electrical codes.

Fans used to ventilate livestock buildings or other rooms where continuous air movement is

essential should be connected to individual electrical circuits, with a minimum of two circuits per

room.

Single Phase and Three Phase Munters Drives: Power supply for fans to have Circuit Breaker

or Fuse Protection. The installer must refer to NEC and local codes to ensure safety and

compliance. See Figure 8A & 8B.

If recommended lightning protection was purchased, wire it to the fan power supply as shown and secure the

lightning protection unit near the disconnect or the bus panel. See Figure 8B & 8C (page 8).

NOTE: A safety cut-off switch should be located adjacent to each fan.

KEY:

L1=Line 1

L2=Line 2

L3=Line 3

H=Hot

N=Neutral

G=Ground

WARNING

High Voltage, disconnect power

before servicing.

Table des matières

Autres manuels Munters Ventilateur

Munters

Munters Breeze Fan Manuel d'instructions

Munters

Munters EDC GHp Series Manuel d'instructions

Munters

Munters WF50 Series Manuel utilisateur

Munters

Munters AT16FPT Manuel utilisateur

Munters

Munters EDC GHp Series Manuel d'instructions

Munters

Munters EM52 Manuel d'instructions

Munters

Munters Aerotech VX36DFCP-H Series Manuel utilisateur

Munters

Munters VX55 Manuel utilisateur

Munters

Munters TU600 Manuel d'instructions

Munters

Munters VX Series Manuel utilisateur

Munters

Munters ATLAS 74 Manuel utilisateur

Munters

Munters EM36 Manuel d'instructions

Munters

Munters EC52D Manuel d'instructions

Munters

Munters Aerotech VX36DF Series Manuel utilisateur

Munters

Munters EC52 Manuel d'instructions

Munters

Munters EM50 Manuel d'instructions

Munters

Munters WM54K Manuel utilisateur

Munters

Munters EC52 Manuel utilisateur

Munters

Munters CX24 Manuel utilisateur

Munters

Munters EC50 Manuel d'instructions

Munters

Munters BI28M Manuel utilisateur

Munters

Munters EC52 Manuel utilisateur

Munters

Munters WM54F Manuel d'instructions

Munters

Munters EDC24HE Manuel d'instructions

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage