Munters Horizon Series Manuel utilisateur

1© Munters Corporation, August 2022 QM1217r0

Instruction Manual

Horizon Series

CSI24 Continuous Sidewall Inlet

Models: CSI24100SF • CSI2410SF • CSI24100CF •

CSI2410CF

HORIZON

CSI24

Continuous

Sidewall Inlet -

Flush Mount

CSI24 Continuous Sidwall Inlet - Straight Rack

Room Side View

CSI24 Continuous Sidwall Inlet - Straight Rack

Outside/Hallway Side View

2QM1217r0

CSI24 Continuous Sidewall Inlet

Instructions for Use and Maintenance

Thank You:

Thank you for purchasing a Munters CSI24 Continuous Sidwall Inlet. Munters equipment is designed to be the

highest performing, highest quality equipment you can buy. With the proper installation and maintenance it will

provide many years of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be

installed and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper

installation or maintenance shall not be considered a defect under the Warranty.

3 Munters Corporation, August 2022 QM1217r0

Index

Chapters Page

1. Unpacking the Equipment 4

1.1 Catalog Number Deﬁ nition 4

1.2 Parts List 4-6

2. Installation Instructions 7

2.1 Framing 7

2.2 Foam Seal 8

2.3 Door Assembly 9

2.4 Left Door Assembly 9

2.5 Middle Door Assembly 12

2.6 Right Door Assembly 14

2.7 Door Installation 17

2.8 Drive Frame Installation 22

2.9 Actuator Installation 26

2.10 Drive Pipe Preperation 26

2.11 Drive Pipe Installation 27

3. Maintenance 33

4QM1217r0

1.1 System Description

Unpacking the Equipment 1.

Before beginning installation, check the overall condition of the equipment. Remove packing materials, and examine all

components for signs of shipping damage. Any shipping damage is the customer’s responsibility and should be reported

immediately to your freight carrier.

The Munters CSI24 Continuous Sidewall Inlet is a 24"H. door that can be continuous for a total of 150'L. and can be

mounted flush to the wall or offset so the drive pipe can be mounted away from the wall to avoid columns or posts. It

can also use either Straight Racks or Curved Racks. The CSI24 Continuous Sidewall Inlet is sold in 100' Door Kits and

10' Door Kits, an Ending Kit and the Actuator (actuator sold separately). For example: For a system that is 450'L.

with Offset Mount and Straight Racks, operated by 3 Actuators, the customer would receive the following:

(4) CSI24100SF, (5) CSI2410SF, (3) AC2872 and (3) Actuators (actuator sold separately).

Catalog Number Definition:

1.2 Parts List

CSI 24 100 S F

Mounting Type; O = Offset, F = Flush

Style of Rack; S = Straight, C = Curved

Length of Kit; 100 = 100 ft, 10 = 10 ft

Height of Door; 24"

Door Kits Ending Kits

AC2871 = Straight Offset Mount Ending Kit

AC2872 = Straight Flush Mount Ending Kit

AC2873 = Curved Offset Mount Ending Kit

AC2874 = Curved Flush Mount Ending Kit

Each 10'L. CSI24 Door Kit, CSI24Includes:

CSI2410

ID Cat. No. Qty. Description

[1] AC3470 1 Door w/ Hinge, 24"H. x 10'L. x 1.5"T., Blk/Wht, CSI24

[2] AC3440 1 Door Edge Trim, 120"L., GZ

[3] AC1415 1 1" SCHD10 (1.32"O.D.) Pipe x 126"L., SOE, 12GA, GZ

[4] KA2156 2 Foam Seal, P-Shape w/ TAB, 2.14"W. x 1.31"H. x 60"L., BLK

[5] AC3726 1 Straight Rack, 49"Travel, 57"(1450mm) L., GZ

AC3737 1 Curved Rack, 49"Travel, 57"(1450mm) L., GZ

CSI2410 Door Kit

5 Munters Corporation, August 2022 QM1217r0

1.2 Parts (continued)

Unpacking the EquipmentChapter 1

10'L. CSI24 Door Kit (continued)

CSI2410

ID Cat. No. Qty. Description

[6] AC3441 1 Flat Joiner Plate, 12"L., GZ

[7] AC3720 1 Pinion Gear for 1" Pipe, AL

[8] AC3708 1 Housing Rack Pinion Gear, PL

[9] AC3722 1 Pivoting Connector, Rack to Door, AL

[A] KP1257 1 Clevis Pin, ¼ "D x 2"L., ZP

[B] KP1105 1 Hairpin Cotter Pin, 0.59"D x 1.13"L., SS

[C] KS2808 2 M8-1.0, INT-HX, Set Screw, KNRL-CUP, ZP

[D] KS1064 2 3⁄8”-16 x 2.25” Hex Bolt, ZP

[E] KN1717 6 1⁄4”-20 Hex Flange Nylock Nut, SS

[F] KS1513 6 1⁄4”-20 x 2.25” Carriage Bolt, ZP

[G] KN1709 2 3⁄8”-16 Nylock Nut, ZP

[H] KS2282 64 #10-16 x ³⁄₄” HXWSR TEK Screw, SS

[J] KS1402 64 #9-15 x 1½ ” Seal Washer Polebarn Screw, ZP

[K] KS2463 2 1⁄4” x 1½ ” Lag Screw, ZP

[L] KS1080 2 3⁄8”-16 x 1” Hex Bolt, ZP

[M] KW3036 6 3⁄8” Flat Washer, USS, ZP

[10] AC3407 1 Inside Door Support, 24", GZ

[11] AC3417 1 Outside Door Support, 24", GZ

[12] AC3410 2 Rack Mounting Plate, GZ

[13] AC3704

Guide Plate w/BRNZ Bushing, 1" Pipe, L, GZ

[A]

[B]

[C]

[D]

[E]

[F]

[G]

[H]

[J]

[K]

6QM1217r0

Unpacking the EquipmentChapter 1

1.2 Parts (continued)

Each AC2872 Ending Kit, Flush, Straight Rack Includes:

ID Cat. No. Qty. Description

[4] KA2156 1 Foam Seal, P-Shape w/ TAB, 2.14"W. x 1.31"H. x 60"L., BLK

[5] AC3726 1 Straight Rack, 49"Travel, 57"(1450mm) L., GZ

AC3737 1 Curved Rack, 49"Travel, 57"(1450mm) L., GZ

[7] AC3722 1 Pivoting Connector, Rack to Door, AL

[8] AC3708 1 Housing Rack Pinion Gear, PL

[9] AC3720 1 Pinion Gear for 1" Pipe, AL

[12] AC3710 2 Rack Mounting Plate, GZ

[13] AC3704 1 Guide Plate w/BRNZ Bushing, 1" Pipe, L, GZ

[15] AC3484 2 Door End Trim, 24"L., CSI24, GZ

[16] AC3706 1 Straight Coupling, Actuator to 1" Pipe, 3.5" to CL, GZ

[A] KP1257 1 Clevis Pin, ¼"D x 2"L., ZP

[B] KP1105 1 Hairpin Cotter Pin, 0.59"D x 1.13"L., SS

[C] KS2808 2 M8-1.0, INT-HX, Set Screw, KNRL-CUP, ZP

[D] KS1064 3 3⁄8”-16 x 2.25” Hex Bolt, ZP

[E] KN1717 13 1⁄4”-20 Hex Flange Nylock Nut, SS

[F] KS1513 6 1⁄4”-20 x 2.25” Carriage Bolt, ZP

[G] KN1709 3 3⁄8”-16 Nylock Nut, ZP

[H] KS2282 20 #10-16 x ³⁄₄” HXWSR TEK Screw, SS

[K] KS2463 2 1⁄4” x 1½” Lag Screw, ZP

[L] KS2466 4 3⁄8” x 2” Lag Screw, ZP

[A]

[B]

[C]

[D]

[E]

[F]

[G]

[H]

[K]

[L]

7 Munters Corporation, August 2022 QM1217r0

Installation Instructions 2.

2.1 Framing

Figure 1A

Chart A

Catalog No. Length Height

Example Door Length (--)4" Door Height (--)2”

(1) CSI24100SF & (5) CSI2410SF

(150'L. x 24"H.) 149'-8" 22"

Step 1A

The CS2410SF was designed for the door to be installed in the room and the Actuator and Pipe Drive system

be mounted in the hallway. Construct the framed opening to correct size according to Chart A (below) and

your CSI24 Continuous Sidewall Inlet size. See Chart A. If installing 2 or more sections of CSI24 doors,

be sure to leave 24" minimum between each framed opening.

See Figure 1A

. Use Treated 2x6's for the

Framing.

Door Length --4"

22"

2x6 Treated

Figure 1B

HALLWAY SIDE

Wall Material

10'-0" O.C.

2x4 Treated

Step 1B

On the hallway side of the framing, install a treated 2x4, 18" from the end framing and then every 10'-0"

O.C. down the length of the framing with the last 2x4 being 18" from the opposite end framing. These 2x4's

should span the top and bottom framing. Also, install double treated 2x6's on the end of the framed opening

to be used to moun the LA actuator to.

See Figure 1B

18"

24"

Double 2x6 Treated

2x6 Treated

8QM1217r0

Installation InstructionsChapter 2

Step 2

After the Framed Openings are completed, make sure the surface of the 2x lumber is clean and free from

debris. The P-Shaped Foam Seal [4], comes in 60" lengths. Starting at 2" from the inside edge of the End

Framing, so that it will overlap the side Foam Seal, peal the back from the adhesive on the back of the Foam

Seal and affix to the framing with the top of the "P" flush with the top of the framing. See Figure 2A and 2B.

For the Foam Seal on the End Framing, the top of the "P" should be flush with the inside edge of the framing

and should run from the inside edge of the Top Framing to the bottom of the Foam Seal on the next frame

member. See Figure 2A and 2B.

Step 3

Continue attaching the P-Shaped Foam Seal until there is Foam Seal attached to 3 sides of each Framed

Opening. Once the Foam Seal is completely attached, go back and permanently attach to the framing

using Staples or Nails in the nailing grove of the Foam Seal Flap. Staples or Nails are not provided and

should be spaced every 4" -- 6". See Figure 2A and 2B.

2.2 Foam Seal

Staple or Nail

(not provided)

Figure 2A

Figure 2B

Framing

P-Shaped Foam Seal [4]

2x4 Framing

9 Munters Corporation, August 2022 QM1217r0

Installation InstructionsChapter 2

Step 4

Each CSI24 Inlet system that is 30'L. or longer consists of (1) Left Door, (1 or more) Middle Doors and

(1) Right Door. The number of Middle Doors depends on the length of the run of CSI24 Doors. For example,

if the run of CSI24 Doors is 40'L. then there is (1) Left Door, (2) Middle Doors and (1) Right Door. If the run

is 100'L. then there is (1) Left Door, (8) Middle Doors and (1) Right Door. In the next steps all the doors will

be assembled before installing them to the framed openings. See Figure 3. If the run is only 20'L. then there

is only the Left Door and the Right Door.

Figure 3

View from Hallway/Hinge Side

TEK Screw [H]

TEK Screw [H] location

for Left End Door

Door Edge Trim [2]

Figure 4

Do not use

this hole at

this time.

2.3 Door Assembly

Step 5

Slide Door Edge Trim [2] onto the bottom edge of the CSI24 Door [1] and secure it with (14) TEK Screws [H]

through the (6) single holes in the middle area of the Door Edge Trim and the left most hole. See Figure 4.

Middle Door

Right Door

Left Door

2.4 Left Door Assembly

NOTE: The Left and Right ends of the system are

determined from the Hallway/Actuator side of

the inlet, with the inlet mounted in the room.

CSI24 Door with Hinge [1]

10 QM1217r0

Installation InstructionsChapter 2

Step 6

Slide a Door End Trim [15] over the Left Door and secure in place with (8) TEK Screws [H]. See Figure 5.

Figure 5

TEK Screw [H]

Door End Trim [15]

Step 7

For the Left Door, attach a Rack Mounting Plate [12] on each side of the door to the left pair of holes in the

Door Edge Trim using (2) TEK Screws [H] per Plate. See Figure 6. Then attach an Outside Door Support [11]

(24") at the right end of the CSI24 Door, on the room side, so that half of the Support is on the Door and the

other half of the Support hangs off the end. See Figure 6.

Figure 6

Rack Mounting Plate [12]

Left Pair of Holes

TEK Screw [H]

CSI24 Door with Hinge

Outside Door

Support [11]

CSI24 Door with Hinge

TEK Screw [H]

Room Side shown

for clarity

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Munters Ventilateur

Munters

Munters EDC GHp Series Manuel d'instructions

Munters

Munters EC52 Manuel d'instructions

Munters

Munters AX Series Manuel utilisateur

Munters

Munters EC52D Manuel d'instructions

Munters

Munters Aerotech VX36DFCP-H Series Manuel utilisateur

Munters

Munters Aerotech VX36DF Series Manuel utilisateur

Munters

Munters EDHE Series Manuel d'instructions

Munters

Munters WF54 Manuel utilisateur

Munters

Munters VX Series Manuel utilisateur

Munters

Munters WM54K Manuel utilisateur

Munters

Munters Euroemme FI Manuel utilisateur

Munters

Munters EM36 Manuel d'instructions

Munters

Munters ATLAS 74 Manuel utilisateur

Munters

Munters TU600 Manuel d'instructions

Munters

Munters GB Series Manuel utilisateur

Munters

Munters EC52 Manuel d'instructions

Munters

Munters WM54K Manuel utilisateur

Munters

Munters AT14F Manuel utilisateur

Munters

Munters MFS36 Manuel d'instructions

Munters

Munters EDC Series Manuel d'instructions

Munters

Munters CX Series Manuel utilisateur

Munters

Munters AT14F Manuel utilisateur

Munters

Munters WS55 Manuel utilisateur

Munters

Munters WF50 Series Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage