MSI 694 MASTER Manuel utilisateur
CHAPTER 1 INTRODUCTION
1-1
Chapter 1
INTRODUCTION
The 694 Master (MS-6309 ver 3.0) ATX mainboard is a high-performance
computer mainboard based on VIA®VT82C694X chipset. The 694 Master
(MS-6309 ver 3.0) is designed for the Intel®CeleronTM or Coppermine (FC-
PGA) processor for inexpensive business/personal desktop markets.
TheApolloPro133A(VT82C694X)isaSocket-370systemlogicnorthbridge
with the addition of 133 MHz capability for both the CPU and SDRAM
interfaces. Apollo Pro133A may be used to implement both desktop and
notebook personal computer systems from 66MHz to 133MHz based on
Socket-370. The primary features of the Apollo Pro133A-North Bridge are:
Slot-1orSocket-370CPU(FrontSideBus) Interface (66 /100/ 133MHz),
DRAMMemory Interface (66/100 / 133MHz),AGPBus Interface (66MHz),
PCIBusInterface (33MHz), Mobile Power Management.
TheVT82C686B PSIPC (PCISuper-I/O Integrated PeripheralController) is a
high integration, high performance, power-efficient, and high compatibility
device that supports Intel and non-Intel based processor to PCI bus bridge
functionality to make a complete Microsoft PC99-compliant PCI/ISA system.
CHAPTER 1 INTRODUCTION
1-2
Mainboard Features
CPU
lSocket 370 for Intel®CeleronTM/ Coppermine processor.
lSupports233MHz,266MHz,300MHz,333MHz,350MHz,400MHz,
450MHz,500MHZ,533MHzto1GHz.
Chipset
lVIA®694Xchipset (510BGA)
-AGP 4x and PCI plus Advanced ECC Memory Controller
-Support PC100/133 SDRAM, VCM technology
lVIA®VT82C686Bchipset(352BGA)
- Advanced Power Management Features
-IntegratedSuperI/O(FDC,LPT,COM1/2,andIR)
- DirectSound AC97 Audio
-DualbusMasterIDEUltraDMA33/66/100
-ACPI
ClockGenerator
l66.6MHz,100MHz and133MHz clocks are supported.
MainMemory
lSupport eight memory banks using four 168-pin unbuffered DIMM.
lSupportamaximum memorysizeof 2GB(32Mx 8).
lSupportECC(1-bitErrorCodeCorrect)function.
lSupport 3.3v SDRAM DIMM.
Slots
lOne AGP (Accelerated Graphics Port) slot.
- AGP specification compliant
- AGP66MHz 3.3v/1.5v for 2x/4x device support
lOne CNR (Communication Network Riser) slot which support Modem
only.
lSix 32-bit Master PCI Bus slots.
lSupports 3.3v/5v PCI bus Interface.
CHAPTER 1 INTRODUCTION
1-3
On-BoardIDE
lAnIDEcontroller on the VIA®VT82C686BChipset provides IDE HDD/
CD-ROM with PIO, Bus Master and Ultra DMA 33/66/100 operation
modes.
lCan connect up to four IDE devices.
On-BoardPeripherals
lOn-BoardPeripherals include:
-1 floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and
2.88Mbytes.
-2 serial ports (COMA + COMB)
- 1 parallel port supports SPP/EPP/ECP mode
- 4 USB ports
- 1 IrDA/HP connector for SIR
-1394 (optional)
Audio
lChip Integrated (Software Audio)
-AC’97Compliant
BIOS
lThe mainboard BIOS provides “Plug & Play” BIOS which detects the
peripheral devices and expansion cards of the board automatically.
lThe mainboard provides a Desktop Management Interface (DMI)
function which records your mainboard specifications.
Dimension
lATXForm Factor: 30.5cm(L) x21cm (W)x4 layersPCB
Mounting
l6 mounting holes.
CHAPTER 1 INTRODUCTION
1-4
PCI SLOT 3
PCI SLOT 2
PCI SLOT 1
ATX
Power Supply
VIA
694X
chipset
Socket 370
DIMM 2
Top: mouse
Bottom:
keyboard
Top:Port 1
USB
DIMM 3
IDE1
Bottom:
Port2
IDE2 FDD
VT82C686B
JMDM1
JFP1
JGS1
JGL1
JBAT1
JWOL1
JPH
JAUX
CPUFAN
BATT
+
Top: LPT
Bottom:
COMA
COMB
Top: Midi/
GamePort
Bottom:
Line-Out
Line-In
Mic
694 Master (MS-6309 ver 3.0) Mainboard
JCD
USB2
JRMS1
CNR1
AGP Slot
SYSFAN
JVTT
DIMM 1
PCI SLOT 4
PCI SLOT 5
J4
BIOS
Mainboard Layout
J3
VT1611A
DIMM 4
PCI SLOT 6
JFSH1
J2
DiagnosticLED
JSPK1
J601
CHAPTER 2 HARDWARE INSTALLATION
2-1
CPU
CPU
Chapter 2
HARDWARE INSTALLATION
Central Processing Unit: CPU
The mainboardoperates with Intel®CeleronTM/Pentium®III(FC-PGA)
processor. The mainboard uses a CPU socket called Socket 370 for easy
CPU installation. The CPU should always have a Heat Sink and a cooling
fan attached to prevent overheating.
3. Press the lever down to
complete the installation.
2. Locate Pin 1 in the socket
and look for the white dot or
cut edge in the CPU. Match
Pin 1 with the white dot/cut
edge. Then, insert the CPU.
It should insert easily.
OpenLever
Pin1
Sliding
Plate
White dot/
Cut edge
Close
Lever
1. Pull the lever sideways away
from the socket. Then, raise
the lever up to a 90-degree
angle.
Pin1
••
••
•CPU Installation Procedures
CHAPTER 2 HARDWARE INSTALLATION
2-2
The BIOS can be used to set the CPU Host Bus Frequency Clock.
If CPUClock = 66MHz
Core/Bus ratio = 3.5
then CPU core speed = Host Clockx Core/Bus ratio
= 66MHzx3.5
= 233MHz
•CPU Core Speed Derivation Procedure
CHAPTER 2 HARDWARE INSTALLATION
2-3
•Fan Power Connectors: CPUFAN & SYSFAN
These connectors support system cooling fan with + 12V. It supports
three pin head connector. When connecting the wire to the connec-
tor, always take note that the red wire is the positive and should be
connected to the +12V, the black wire is Ground and should be
connected to GND. If your mainboard has System Hardware Monitor
chipset on-board, you must use a specially designed fan with speed
sensor to take advantage of this function.
For fans with fan speed sensor, every rotation of the fan will send out 2
pulses. System Hardware Monitor will count and report the fan rotation
speed.
Note: Always consult your reseller for proper CPU cooling fan.
CPUFAN
CPUFAN: ProcessorFan
SYSFAN: System Fan
+12V
GND
SENSOR
SYSFAN
+12V
GND
SENSOR
CHAPTER 2 HARDWARE INSTALLATION
2-4
Clear CMOS Jumper: JBAT1
A battery must be used to retain the mainboard configuration in CMOS
RAM. Short 1-2 pins of JBAT1 to store the CMOS data.
Keep Data Clear Data
11
3
3
Note: You can clear CMOS by shorting 2-3 pin, while the system is off.
Then, return to 1-2 pin position. Avoid clearing the CMOS while
the system is on, it will damage the mainboard. Always unplug
the power cord from the wall socket.
22
1
3
JBAT1
CHAPTER 2 HARDWARE INSTALLATION
2-5
Memory Installation
••
••
•Memory Bank Configuration
Themainboard supports a maximum memory size of 2GB (256-bittechnol-
ogy)SDRAM: It provides four 168-pin unbufferedDIMMs (Double In-Line
Memory Module) sockets. It supports 8 MB to 512 Mbytes DIMM memory
module.
DIMM1(Bank0+Bank1)
DIMM2(Bank2+Bank3)
DIMM3(Bank4+Bank5)
DIMM4(Bank6+Bank7)
There are three kinds of DIMM specification supported
by this mainboard: PC133, PC100 and PC66. If you
use 66MHz CPU Bus Frequency, these four DIMM
Specs. is supported. If you use 100 MHz CPU Bus
Frequency, only PC100 DIMM Specs. is supported.If
you use 133 MHz CPU Bus Frequency, only PC133
DIMM Specs. is supported.
!
WARNING!
CHAPTER 2 HARDWARE INSTALLATION
2-6
A. HowtoinstallaDIMMModule
1. The DIMM slot has 2 Notch Keys “VOLT and DRAM”, so the
DIMM memory module can only fit in one direction.
2. Insert the DIMM memory module vertically into the DIMM slot.
Then push it in.
3. The plastic clip at the side of the DIMM slot will automatically
close.
Single Sided DIMM
Double Sided DIMM
VOLTDRAM
••
••
•Memory Installation Procedures
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels MSI Carte mère
MSI
MSI Z77IA-S01 Series Manuel utilisateur
MSI
MSI H81I Manuel utilisateur
MSI
MSI MS-7317 Manuel utilisateur
MSI
MSI X299 SLI PLUS Manuel utilisateur
MSI
MSI MS-6318 Manuel utilisateur
MSI
MSI MS-7199 Manuel utilisateur
MSI
MSI Intel RAID Manuel utilisateur
MSI
MSI H6M-P30 (B3) Manuel utilisateur
MSI
MSI MS-7760 Manuel utilisateur
MSI
MSI Z87-G55 Manuel utilisateur
MSI
MSI K9NBPM2-FID Series Manuel utilisateur
MSI
MSI MAG B760M MORTAR MAX WIFI Manuel utilisateur
MSI
MSI MS-98H2 Manuel utilisateur
MSI
MSI B250M PRO-VH Manuel utilisateur
MSI
MSI MS-98J4 Manuel utilisateur
MSI
MSI Microstar MS5116 Manuel utilisateur
MSI
MSI KA780G Series Manuel utilisateur
MSI
MSI K7T266 Pro-R Manuel utilisateur
MSI
MSI B85M GAMING Manuel utilisateur
MSI
MSI H170M ECO Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
