Motorola RFS6000 Series Manuel utilisateur
RFS6000 Series RF Switch
Installation Guide
M
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office.
Symbol is a registered trademark of Symbol Technologies, Inc. All other product or service
names are the property of their respective owners. © Motorola, Inc. 2008. All rights reserved.
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.0 LED Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.0 Hardware Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.0 Part Numbers, Support, and Sales . . . . . . . . . . . . . . . . . . . . . 24
7.0 End-User License Agreement . . . . . . . . . . . . . . . . . . . . . . . . . 25
Contents
4
Introduction 1
1 Introduction
The Motorola RFS6000 Series RF Switch is a high-performance member of Motorola’s Wireless
Switch family. The RFS6000 Series RF Switch provides centralized Wireless LAN (WLAN)
configuration and management by coalescing a network “intelligence” previously spread across
physically distributed access points. By replacing access points with simpler access ports (or “thin”
access points), the RFS6000 Series RF Switch becomes a WLAN’s single point of contact, thus
reducing wireless networking complexity by moving management out of the ceiling and into the
wiring closet. In addition, through the use of patented Virtual AP architecture, the RFS6000 Series
RF Switch lets you create multiple WLANs without changing or adding to the existing wired network
infrastructure.
This document is written for the network device installer.
1.1 Package Contents
Inspect the package contents and report any missing or damaged items to your sales representative.
The package should contain the following:
• RFS6010 RF Switch with Rack Brackets installed
• Console Cable
•Installation Guide (this document)
• China RoHS compliance document
1.2 Document Conventions
The following graphical alerts are used in this document to indicate notable situations:
NOTE Tips, hints, or special requirements that you should take note of.
CAUTION Care is required. Disregarding a caution can result in data loss or
equipment malfunction.
WARNING! Indicates a condition or procedure that could result in personal injury or
equipment damage.
!
Introduction 2
1.3 Warnings
•Read all installation instructions and site survey reports, and verify correct equipment installation before connecting
the system to its power source.
•Remove jewelry and watches before installing this equipment.
•Install the equipment in a rack with adequate dimensions and weight allowances.
•Verify the rack is anchored and cannot tip over or break away from its mountings.
•Verify the unit is grounded before connecting it to the power source.
•Verify any device connected to this unit is properly wired and grounded.
•Connect all power cords to a properly wired and grounded electrical circuit.
•Verify the electrical circuits have appropriate overload protection.
•Attach only approved power cords to the device.
•Motorola strongly recommends the use of an Uninterruptible Power Supply (UPS) that supports the RFS6000 Series
RF Switch power rating. Not using a UPS can result in data loss or equipment damage due to a power surge or power
failure.
•Verify that the power connector and socket are accessible at all times during the operation of the equipment.
•Do not work with power circuits in dimly lit spaces.
•Do not install this equipment or work with its power circuits during thunderstorms or other weather conditions that
could cause a power surge.
•Verify there is adequate ventilation around the device, and ambient temperatures meet equipment operation
specifications.
1.4 Site Preparation
•Consult your site survey and network analysis reports to determine specific equipment placement, port capacity,
power drops, and so on.
•Assign installation responsibility to the appropriate personnel.
•Identify where all installed components are located.
•Verify appropriate rack mounting requirements.
•Provide a sufficient number of power drops for your equipment.
•Ensure adequate, dust-free ventilation to all installed equipment.
•Identify and prepare Ethernet and console port connections.
•Verify that cable lengths are within the maximum allowable distances for optimal signal transmission.
•Verify that the RFS6000 Series RF Switch is powered through an Uninterruptible Power Supply (UPS).
Specifications 3
2 Specifications
2.1 Physical Specifications
2.2 Power Cord Specifications
A power cord is not supplied with the switch. Use only a correctly rated power cord certified (as
appropriate) for the country of operation.
2.2.1 Power Protection
•If possible, use a circuit dedicated to data processing equipment. Commercial electrical
contractors are familiar with wiring for data processing equipment and can help with the load
balancing of these circuits.
•Install surge protection. Be sure to use a surge protection device between the electricity
source and the RFS6000 Series RF Switch.
•Install an Uninterruptible Power Supply (UPS). A UPS provides continuous power during a
power outage. Some UPS devices have integral surge protection. UPS equipment requires
periodic maintenance to ensure reliability. A UPS of the proper capacity for the data processing
equipment must be purchased.
Width 440mm (17.32 in)
Height 44.45mm (1.75 in)
Depth 390.8mm (15.38 in)
Weight 6.35 Kg (14.0 lbs)
Operating Temperature 0°C - 40°C
Operating Humidity 5% - 85% RH, non-condensing
Operating Altitude 3 km (10000 ft)
LED Codes 4
3 LED Codes
The RFS6010 RF Switch has four vertically-stacked LEDs on its front panel. Each of the switch’s
Gigabit Ethernet ports have two status LEDs. These LEDs display two colors (green & amber), and
three lit states (solid, blinking, and off). The following tables decode the combinations of LED colors
and states for the System Status LEDs and the Gigabit Ethernet LEDs.
3.1 System Status LEDs
System Status 1
Fan status
Temperature status
System Status 2
LED Codes 5
3.1.1 Start Up / POST (Primary System or Redundant System)
3.1.2 Switch Status (Primary System)
3.1.3 Switch Status (Redundant System)
System Status 1 LED System Status 2 LED Event
Off Off Power off
Green Blinking Green Blinking Power On Self Test (POST) running
Green Solid Green Blinking POST succeeded (Operating System Loading)
Green Solid Off POST succeeded (Normal Operation)
Amber Blinking Off POST Failure
Alternating Green Blinking
& Amber Blinking
Alternating Green Blinking
& Amber Blinking Boot Up Error: Device has an invalid checksum
NOTE During switch start up, the Temperature status LED will be lit Solid
Amber. This is normal behavior and does not indicate an error. At the
completion of start up the Temperature Status LED will switch to Solid
Green.
System Status 1 LED System Status 2 LED Event
Off Off Power off
Green Solid Off No Redundancy Feature Enabled
Green Solid Green Solid Redundancy Feature Enabled
Actively Adopting Access Ports
Green Solid Amber Blinking
No License to adopt Access Ports
or
No Country Code configured on the switch
or
License and Country Code configured, but no
APs adopted
System Status 1 LED System Status 2 LED Event
Off Off Power off
Green Solid Off No Redundancy Feature Enabled
LED Codes 6
3.1.4 Fan LED
3.1.5 Temperature Status LED
Green Blinking Green Solid Redundant System failed over and adopting
ports
Green Blinking Alternating Green Blinking
& Amber Blinking Redundant System not failed over.
Green Solid Amber Blinking
No License to adopt Access Ports
or
No Country Code configured on the switch
or
License and Country Code configured, but no
APs adopted
Fan LED Event
Off System Off / POST Start
Green Blinking POST in Process
Green Solid All System Fans Normal Operation
Amber Solid Redundant Cooling Failure
System Operational
Amber Blinking
System Cooling Failure
System will be held in reset until the issue is
resolved
Temperature LED Event
Off System Off
Green Solid Ambient Inlet Temperature is within specified
operating limit
Amber Solid
Ambient Inlet Temperature is near the maximum
operating temperature
During switch start up this LED will be lit Solid
Amber. This is normal behavior and does not
indicate an error.
System Status 1 LED System Status 2 LED Event
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels Motorola Changer
Motorola
Motorola RFS7000 Series Manuel utilisateur
Motorola
Motorola WS2000 - Wireless Switch - Network Management... Manuel utilisateur
Motorola
Motorola RFS Series Manuel utilisateur
Motorola
Motorola M68ICS08JB Manuel utilisateur
Motorola
Motorola WS5100 Series Manuel utilisateur
Motorola
Motorola RFS7000 Series Manuel utilisateur
Motorola
Motorola RFS7000 Series Manuel utilisateur
Motorola
Motorola WS2000 - Wireless Switch - Network Management... Mode d’emploi
Motorola
Motorola RFS7000 Series Manuel utilisateur
Motorola
Motorola AP-PSBIAS-1P2-AFR Manuel utilisateur
Motorola
Motorola RFS Series Manuel utilisateur
Motorola
Motorola 549478-001-00 - PowerBroadband EthernetXD M2a WallPlate... Manuel utilisateur
Motorola
Motorola EX-3524 Mode d’emploi
Motorola
Motorola RFS6000 - Wireless RF Switch Manuel utilisateur
Motorola
Motorola WS2000 - Wireless Switch - Network Management... Manuel utilisateur
Motorola
Motorola RFS7000GR Manuel utilisateur
Motorola
Motorola RFS7000 Series Manuel utilisateur
Motorola
Motorola T2-2500 Manuel utilisateur
Motorola
Motorola DIMETRA MTS 4 Manuel utilisateur
Motorola
Motorola RFS6000 - Wireless RF Switch Manuel utilisateur
