ML Accessories 12DC50D Mode d’emploi

INSTALLATION & MAINTENANCE MANUAL

12DC50D / 24DC50D / 24DC100D

These instructions should be read carefully and retained after installation by the end user for

future reference and maintenance.

These instructions should be used to aid installation of the following products:

12DC50D / 24DC50D / 24DC100D

GENERAL INSTRUCTIONS

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)

and current Building Regulations. If in any doubt, consult a qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this product is ﬁtted) does not exceed the rating of the

circuit cable, fuse, or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• Do not overload this accessory or subject it to conditions outside its rating

• This product is for indoor use only

• This product is Class II double insulated

• This product is IP20 rated

SAFETY

INSTALLATION

• Provide power to the required point of installation

• Connect the LED driver to the mains supply ensuring the correct polarity is observed (see Fig 1). Live

(brown), Neutral (blue)

GENERAL

WARNING

This product must be disconnected from the circuit if it subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

The maximum constant ambient temperature at the point of installation should not exceed 50 degrees

centigrade.

This product is dimmable with trailing edge dimmers, please check compatibility before installation.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

• Connect a suitable LED load to the secondary side of the driver + (red) – (black)

• Ensure cable strain relief is securing the cables effectively

• Switch on power supply and check for correct operation

Dimmable LED Drivers

These instructions should be read carefully and retained after installation by the end user for future reference and

maintenance.

These instructions should be used to aid installation of the following products:

12DC50D / 24DC50D / 24DC100D

SAFETY

•Installation of this driver should only be carried out by a qualified electrician or competent person to the

latest Building and current IEE Wiring Regulations (BS7671)

•Please isolate mains prior to installation/maintenance

•Check the total load on the circuit (including when this driver and LED load is fitted) does not exceed the

rating of the circuit cable, fuse or circuit breaker

•Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation

•This unit is rated at IP20

•This product is Class II and does not require an earth

•This product should be placed in a suitable enclosure

•This product is dimmable with most trailing edge dimmers (check compatibility with dimmer manufacturer)

INSTALLATION

•Provide power to the required point of installation

•Connect the LED driver to the mains supply ensuring the correct polarity is observed (see Fig 1). Live (brown),

Neutral (blue)

Fig 1

•Connect a suitable LED load to the secondary side of the driver + (red) –(black)

•Ensure cable strain relief is securing the cables effectively

•Switch on power supply and check for correct operation

WARNING

This product must be disconnected from the circuit if it subjected to any high voltage or insulation resistance testing.

Irreparable damage will occur if this instruction is not followed.

Secondary

Primary

Fig 1

AVSEP21_v2

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

WARRANTY

This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with

the current edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the

warranty. If this product should fail within its warranty, period it should be returned to the place of purchase for

a free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated

with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter

product speciﬁcation without prior notice.

-20~

50°C

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ML Accessories Équipement d'éclairage

ML Accessories

ML Accessories EMLSUS Mode d’emploi

ML Accessories

ML Accessories WP15CTP Mode d’emploi

ML Accessories

ML Accessories Knightsbridge LEDFS12WW Mode d’emploi

ML Accessories

ML Accessories BL5BK Mode d’emploi

ML Accessories

ML Accessories TRLED12 Mode d’emploi

ML Accessories

ML Accessories FLN10 Mode d’emploi

ML Accessories

ML Accessories SHE1BEMP Mode d’emploi

ML Accessories

ML Accessories BATSCWST4 Mode d’emploi

ML Accessories

ML Accessories T8BLED15EM1 Mode d’emploi

ML Accessories

ML Accessories GUSPBK Mode d’emploi

ML Accessories

ML Accessories Knightsbridge BT9H4/6K Mode d’emploi

ML Accessories

ML Accessories T8LED Series Mode d’emploi

ML Accessories

ML Accessories MLBA6045 Series Mode d’emploi

ML Accessories

ML Accessories SURF418HF Mode d’emploi

ML Accessories

ML Accessories EMLRECL Mode d’emploi

ML Accessories

ML Accessories SPIKEW Mode d’emploi

ML Accessories

ML Accessories 4IPB Mode d’emploi

ML Accessories

ML Accessories SUR5LED Mode d’emploi

ML Accessories

ML Accessories TPOV60B Mode d’emploi

ML Accessories

ML Accessories OWALL1 P Series Mode d’emploi

ML Accessories

ML Accessories SPIKE4BL Mode d’emploi

ML Accessories

ML Accessories TPR14LEDS Mode d’emploi

ML Accessories

ML Accessories EMPDL Mode d’emploi

ML Accessories

ML Accessories SHE1B Mode d’emploi

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur