ML Accessories WP15CTP Mode d’emploi

INSTALLATION & MAINTENANCE MANUAL

WP15CTP

These instructions should be read carefully and retained after installation by the end-user for

future reference and maintenance.

These instructions should be used to aid the installation of the following product:

WP15CTP

GENERAL INSTRUCTIONS

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)

and current Building Regulations. If in any doubt, consult a qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is ﬁtted) does not exceed the rating of the

circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation

• This product is Class I and must be earthed

• This product is IP65 rated

SAFETY

INSTALLATION

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please conﬁrm with the

manufacturer of the sensors that they are compatible with LED luminaires

• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable

IP rated junction boxes should be used where required

• The power source connections should be local and accessible via a suitable IP rated enclosure

• Round cable should be used for the mains supply. The use of ﬂat cable will cause water ingress to the ﬁtting

• Unscrew the four front screws to gain access (see Fig. 1)

Fig. 1

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end-user for future reference

and maintenance.

These instructions should be used to aid the installation of the following product:

WP15CTP

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of

the circuit cable, fuse or circuit breaker

•Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for

installation

•This product is Class I and must be earthed

•This product is IP65 rated

INSTALLATION

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the

manufacturer of the sensors that they are compatible with LED luminaires

•Provide power to the required point of installation (refer to BS7671 for correct

cabling methods). Suitable IP rated junction boxes should be used where required

•The power source connections should be local and accessible via a suitable IP rated enclosure

•Round cable should be used for the mains supply. The use of flat cable will cause water ingress to the

fitting

•Unscrew the four front screws to gain access inside (see Fig. 1)

Fig. 1

• Attach the EVA pad to the back of the plate (see Fig. 2)

Fig. 2

• Using the backplate as a template, mark the location for, and drill the ﬁxing holes ensuring not to infringe

with any gas/water pipes or electrical cables

• Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate to the

surface. Rubber washers or sealant should be applied around the screw heads to prevent water ingress

(see Fig. 3)

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

This product is not suitable for installation in or near a coastal or marine environment.

•Attach the EVA pad to the back of the plate (see Fig. 2)

Fig. 2

•Using the backplate as a template, mark the location for, and drill the fixing holes ensuring not to

infringe with any gas/water pipes or electrical cables

•Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate to the

surface. Rubber washers or sealant should be applied around the screw heads to prevent water

ingress (see Fig. 3)

Fig. 3

•For surface mounted wiring, a suitable IP rated gland can be used to feed through the side of the

backplate

•Connect the luminaire to the mains supply ensuring that correct polarity is observed: L - Live (Brown),

E - Earth (Green/Yellow), N - Neutral (Blue)

Note –Please note this luminaire comes with the photocell not connected. To use the features of the photocell,

please plug the photocell plug into the socket

•Select the colour temperature via the 3-position switch

•Fit the luminaire to the baseplate and secure with the four screws

•Switch on and check for correct operation

WARNING

This luminaire must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

The LED lamps fitted in this product are non-replaceable. The product should be recycled in the correct manner

when it reaches the end of its life. Check local authorities for where facilities exist.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

Fig. 3

• For surface mounted wiring, a suitable IP rated gland can be used to feed through the side of the backplate

• Connect the luminaire to the mains supply ensuring that correct polarity is observed: L - Live (Brown),

E -Earth (Green/Yellow), N - Neutral (Blue)

Note – Please note this luminaire comes with the photocell not connected. To use the features of the

photocell, please plug the photocell plug into the socket

• Select the colour temperature via the 3-position switch

• Fit the luminaire to the baseplate and secure with the four screws

• Switch on and check for correct operation

WARRANTY

This product has a warranty of 5 years from the date of purchase. Failure to install this product in accordance

with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code

will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the

place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any

installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories

reserve the right to alter product speciﬁcation without prior notice.

GENERAL

This product contains a light source of energy efﬁciency class D to Regulation (EU) No. 2019/2015.

and (UK) 2021 No. 1095.

This product contains a non-replaceable LED light source and non-replaceable control gear.

WP15CTP

As existing but replace the following two sections:

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

This product is not suitable for installation in or near a coastal or marine environment.

GENERAL

This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015.

This product contains a non-replaceable LED light source and non-replaceable control gear.

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not use

aggressive cleaning products or solvents which may damage the product.

Do not use any source of high-pressure washers to maintain or clean this luminaire.

This product is non-dimmable.

This product should be dismantled for disposal when it reaches the end of its life. Please see website for

dismantling instructions.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

230V 50Hz, IP65, Class 1, Non-Dim, Ta -40~45

AVxxx21_V2

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not

use aggressive cleaning products or solvents which may damage the product.

Do not use any source of high-pressure washers to maintain or clean this luminaire.

This product is non-dimmable.

This product should be dismantled for disposal when it reaches the end of its life. Please see website for

dismantling instructions.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

AVSEP21_V2

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

122

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

-40~

45°C

Table des matières

Autres manuels ML Accessories Équipement d'éclairage

ML Accessories

ML Accessories GUSPBK Mode d’emploi

ML Accessories

ML Accessories LEDFRA6 Mode d’emploi

ML Accessories

ML Accessories Knightsbridge BT9H4/6K Mode d’emploi

ML Accessories

ML Accessories CAPWGU Mode d’emploi

ML Accessories

ML Accessories NCLB12 Mode d’emploi

ML Accessories

ML Accessories RD1 Series Mode d’emploi

ML Accessories

ML Accessories WP15CTP Mode d’emploi

ML Accessories

ML Accessories SURF236EMHF Mode d’emploi

ML Accessories

ML Accessories UNDKIT3WWW Mode d’emploi

ML Accessories

ML Accessories EA1 Series Mode d’emploi

ML Accessories

ML Accessories OPRCDKIT Mode d’emploi

ML Accessories

ML Accessories OSPCKIT Mode d’emploi

ML Accessories

ML Accessories FL8ABK Mode d’emploi

ML Accessories

ML Accessories SPIKE5S Mode d’emploi

ML Accessories

ML Accessories TRIBCCW Mode d’emploi

ML Accessories

ML Accessories Knightsbridge SPIKEW Manuel

ML Accessories

ML Accessories OWALL1 P Series Mode d’emploi

ML Accessories

ML Accessories ENM5C Mode d’emploi

ML Accessories

ML Accessories AXREMC Mode d’emploi

ML Accessories

ML Accessories SPIKE4BL Mode d’emploi

ML Accessories

ML Accessories SUR5LED Mode d’emploi

ML Accessories

ML Accessories SPIKEW Mode d’emploi

ML Accessories

ML Accessories NH0183BD Mode d’emploi

ML Accessories

ML Accessories 5410A Mode d’emploi

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur