Mitsubishi Electric Q64RD Manuel utilisateur

RTD Input Module

Channel Isolated RTD Input Module

User's Manual

-Q64RD

-Q64RD-G

-GX Configurator-TI (SW1D5C-QTIU-E)

A - 1 A - 1

SAFETY PRECAUTIONS 

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full

attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of

the programmable controller system, refer to the user’s manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

Do not write any data to the "system area" of the buffer memory in the intelligent function

module.

Also, do not use any "use prohibited" signals as an output signal from the programmable

controller CPU to the intelligent function module.

Doing so may cause malfunction of the programmable controller system.

CAUTION

Do not install the control lines or communication cables together with the main circuit lines or

power cables.

Keep a distance of 100mm or more between them.

Failure to do so may result in malfunction due to noise.

A - 2 A - 2

[Installation Precautions]

CAUTION

Use the programmable controller in an environment that meets the general specifications in the

user's manual for the CPU module used.

Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of

the product.

To mount the module, while pressing the module mounting lever located in the lower part of the

module, fully insert the module fixing projection(s) into the hole(s) in the base unit and press the

module until it snaps into place.

Incorrect mounting may cause malfunction, failure or drop of the module.

When using the programmable controller in an environment of frequent vibrations, fix the

module with a screw.

Tighten the screws within the specified torque range.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

Shut off the external power supply (all phases) used in the system before mounting or removing

the module.

Failure to do so may result in damage to the product.

A module can be replaced online (while power is on) on any MELSECNET/H remote I/O station

or in the system where a CPU module supporting the online module change function is used.

Note that there are restrictions on the modules that can be replaced online, and each module

has its predetermined replacement procedure.

For details, refer to the relevant chapter in this manual.

Do not directly touch any conductive and electronic component of the module.

Doing so can cause malfunction or failure of the module.

A - 3 A - 3

[Wiring Precautions]

WARNING

After wiring, attach the included terminal cover to the module before turning it on for operation.

Failure to do so may result in electric shock.

CAUTION

Individually ground the FG terminal of the programmable controller with a ground resistance of

100 or less.

Failure to do so may result in electric shock or malfunction.

Tighten the terminal screws within the specified torque range.

Undertightening can cause short circuit, fire, or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

Prevent foreign matter such as dust or wire chips from entering the module.

Such foreign matter can cause a fire, failure, or malfunction.

A protective film is attached to the top of the module to prevent foreign matter, such as wire

chips, from entering the module during wiring.

Do not remove the film during wiring.

Remove it for heat dissipation before system operation.

Use applicable solderless terminals and tighten them with the specified torque.

If any solderless spade terminal is used, it may be disconnected when the terminal screw comes

loose, resulting in failure.

A - 4 A - 4

[Startup and Maintenance Precautions]

WARNING

Do not touch any terminal while power is on.

Doing so will cause electric shock or malfunction.

Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the terminal screws, connector screws, or module fixing screws.

Failure to do so may result in electric shock or cause the module to fail or malfunction.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

CAUTION

Do not disassemble or modify the modules.

Doing so may cause failure, malfunction, injury, or a fire.

Shut off the external power supply (all phases) used in the system before mounting or removing

the module.

Failure to do so may cause the module to fail or malfunction.

A module can be replaced online (while power is on) on any MELSECNET/H remote I/O station

or in the system where a CPU module supporting the online module change function is used.

Note that there are restrictions on the modules that can be replaced online, and each module

has its predetermined replacement procedure.

For details, refer to the relevant chapter in this manual.

After the first use of the product, do not mount/remove the module to/from the base unit, and the

terminal block to/from the module more than 50 times (IEC 61131-2 compliant).

Exceeding the limit of 50 times may cause malfunction.

Before handling the module, touch a conducting object such as a grounded metal to discharge

the static electricity from the human body.

Failure to do so may cause the module to fail or malfunction.

[Disposal Precaution]

CAUTION

When disposing of this product, treat it as industrial waste.

A - 5 A - 5

CONDITIONS OF USE FOR THE PRODUCT 

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

A - 6 A - 6

REVISIONS

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Nov., 2000 SH (NA)-080142-A First printing

Jun., 2001 SH (NA)-080142-B Addition

Section 2.1, 2.2

Correction

Conformation to the EMC Directive and Low Voltage Instruction, About

the Generic Terms and Abbreviations, Product Structure, Section 5.2,

5.2.1, 5.2.2, 5.3.3

Feb., 2002 SH (NA)-080142-C Addition

Section 1.2, Section 3.4.18, 3.4.19, Chapter 7, App 2,3

Partial addition

SAFETY PRECAUTIONS, About the Generic Terms and Abbreviations,

Section 2.1, Section 3.1, 3.2, 3.4.1, Section 4.3, 4.6, Section 5.2.1, 5.2.2,

Section 8.1, 8.2.1

Correction

Section 3.3.2, 3.4.10, 3.4.17, Section 4.2, 4.4.1, Section 5.3.2, 5.5, 5.6.1

Section 6.1.1, 6.2.2, Section 8.2.4,

Feb., 2003 SH (NA)-080142-D Addition

Section 5.6.3, 5.6.4

Correction

SAFETY PRECAUTIONS, Section 1.2, Section 2.1, Section 3.1.1, 3.2,

3.3.1, 3.3.2, 3.4.1, 3.4.3, 3.4.4, 3.4.6, 3.4.7, 3.4.10 to 3.4.19, Section 4.5,

4.6, Section 5.1, 5.2.1, 5.2.2, 5.3.2, 5.4, 5.5, 5.6.1, 5.6.2, Section 6.1,

6.1.1, 6.1.2, 6.2, 6.2.1, 6.2.2, Section 7.3.1, 7.3.3 to 7.3.6, 7.4,

Section 8.1, 8.2, 8.2.5, Appendix 2.1, Appendix 3.1 to 3.3

Sep., 2003 SH(NA)-080142-E Description for new model, Q64RD-G is added.

Addition

Section 3.1.2, 3.4.2, 3.4.5, 3.4.7, 3.4.12, 3.4.13, 3.4.23, 7.4.2, 8.2.5,

8.2.6, Appendix 1.3

Correction

About the Generic Terms and Abbreviations, Product Lineup, Chapter 1,

Section 1.1, 2.1, 2.2, 3.1.1, 3.1.3, 3.2, 3.2.1, 3.3.1, 3.3.2, 3.4.1, 3.4.4,

3.4.15 to 3.4.17, 3.4.21, 3.4.25, 4.3, 4.4.2, 4.5, 4.6, 5.1, 5.2.1, 5.6.1,

5.6.2, 5.6.4, 6.1, Chapter 7, Section 7.3.4, 7.3.6, 7.4.1, 8.1, 8.2.10,

Appendix 1.1, 1.2, 3.2, 3.3, 4

May, 2004 SH(NA)-080142-F Correction

Section 2.2, 3.4.16, 7.1, 7.3.1 to 7.3.6

Oct., 2004 SH (NA)-080142-G Correction

SAFETY PRECAUTIONS, Section 2.1, Section 3.1.1, 3.3, 3.4.1, 3.4.1,

Section 4.1, Section 6.2, 6.2.1

A - 7 A - 7

Print Date Manual Number Revision

Sep., 2005 SH (NA)-080142-H Addition

Section 3.4.22, 3.4.23, Appendix 2.2, Appendix 2.2.1, Appendix 2.2.2

Correction

Conformation to the EMC Directive and Low Voltage Instruction,

Section 1.2, Section 2.1, 2.2, Section 3.1.1, 3.1.2, 3.2, 3.3.1, 3.3.2, 3.4.1,

3.4.2, 3.4.5, 3.4.6, 3.4.7, 3.4.10, 3.4.14, 3.4.20, 3.4.21, Section 5.1,

5.2.2, 5.6.1, 6.1.1, 6.2.1, Section 7.3.1, 7.3.3, 7.3.4, 8.1, 8.2.10,

Appendix 2.1

Feb., 2006 SH(NA)-080142-I Addition

Appendix 3.1

Correction

SAFETY PRECAUTIONS, Section 1.2, Section 2.2, Section 3.2, 3.4.13,

Section 7.3.3, 7.3.5, Appendix 3, INDEX

Section number changed

Appendix 3.1 Appendix 3.2, Appendix 3.2 Appendix 3.3,

Appendix 3.3 Appendix 3.4

Oct., 2006 SH(NA)-080142-J Correction

Section 4.5

Oct., 2007 SH(NA)-080142-K Correction

Section 1.1, Section 1.2, Section 3.1.1, Section 3.2, Section 3.2.2,

Section 3.2.3, Section 3.3.2, Section 3.4.2, Section 3.4.19,

Section 3.4.22, Section 4.3, Section 6.2.1, Section 8.1, Appendix3.1,

Appendix3.2, Appendix3.3

Jan., 2008 SH(NA)-080142-L Correction

SAFETY PRECAUTIONS, CONTENTS, About the Generic Terms and

Abbreviations, Section 2.2, Section 2.3, Section 4.1, Section 5.2.2

May, 2008 SH(NA)-080142-M Correction

SAFETY PRECAUTIONS, Compliance with the EMC and Low Voltage

Directives, About the Generic Terms and Abbreviations, Section 2.1,

Section 2.3, Section 3.4.19, Section 4.1, Section 5.2.1, Section 5.2.2,

Section 5.3.1 to 5.3.3, Section 7.1

Sep., 2011 SH(NA)-080142-N Addition

CONDITIONS OF USE FOR THE PRODUCT

Correction

SAFETY PRECAUTIONS, COMPLIANCE WITH EMC AND LOW

VOLTAGE, Section 6.1, 6.1.2, WARRANTY

A - 8 A - 8

Print Date Manual Number Revision

May, 2016 SH(NA)-080142-O Correction

SAFETY PRECAUTIONS, COMPLIANCE WITH EMC AND LOW

VOLTAGE DIRECTIVES, ABOUT THE GENERIC TERMS AND

ABBREVIATIONS, PACKING LIST, Chapter 1, Chapter 2, Section 2.1,

Section 2.2, Section 2.3, Section 3.1.1, Section 3.1.2, Section 3.2,

Section 3.2.1, Section 3.3.1, Section 3.3.2, Section 3.4.1, Section 3.4.2,

Section 3.4.4, Section 3.4.6, Section 3.4.7, Section 3.4.8, Section 3.4.9,

Section 3.4.10, Section 3.4.13, Section 3.4.14, Section 3.4.25, Section

4.1, Section 4.3, Section 4.5, Section 4.6, Section 5.2.1, Section 5.2.2,

Section 5.4, Section 5.5, Section 5.6.1, Section 5.6.2, Section 5.6.3,

Section 6.1, Section 6.1.1, Section 6.1.2, Section 6.2, Section 6.2.1,

Section 6.2.2, Chapter 7, Section 7.5, Section 8.1, Section 8.2.8,

Section 8.2.9,

Section 8.2.10, Appendix 1.2, Appendix 1.2.1, Appendix 1.3,

Appendix 2.1, Appendix 2.2, Appendix 2.3, Appendix 3

Section number changed

Appendix 2 Appendix 1, Appendix 2.1 Appendix 1.1,

Appendix 2.2 Appendix 1.2, Appendix 2.2.1 Appendix 1.2.1,

Appendix 2.2.2 Appendix 2.2.1, Appendix 2.3 Appendix 1.3,

Appendix 3.1 Appendix 2.1, Appendix 3.2 Appendix 2.2,

Appendix 3.3 Appendix 2.3, Appendix 3.4 Appendix 2.4,

Appendix 4 Appendix 3

Japanese Manual Version SH-080133-R

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent

licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property

rights which may occur as a result of using the contents noted in this manual.

2000 MITSUBISHI ELECTRIC CORPORATION

Autres manuels pour Q64RD

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Mitsubishi Electric Unité de contrôle

Mitsubishi Electric

Mitsubishi Electric AJ65VBTS32-16DT Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC-F FX2N-1HC Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric EMU4-CNT-MB Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric QD75MH1 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-A7AY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65FBTA42-16DT Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric FR-PU04 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Procon MOD-IP/50 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuel d'installation et d'exploitation

Mitsubishi Electric

Mitsubishi Electric PSSxxMC1Fx Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65BT-RPI-10A Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric PSS**S72FT Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 800 Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R AnyWireASLINK Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65VBTCE32-16DT Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric EMU4-D65 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric GT1020-LBD Instructions d'utilisation et d'entretien

Mitsubishi Electric

Mitsubishi Electric CC-Link IE-NZ2GNSS2-8D Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric EB-50GU-A Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur