Mitsubishi Electric FR-A7AY Manuel utilisateur

INSTRUCTION MANUAL

INVERTER

Plug-in option

FR-A7AY E kit-SC

Analog output function

Digital output function INSTALLATION AND WIRING

PARAMETER LIST

EXTENSION ANALOG OUTPUT

PRE-OPERATION INSTRUCTIONS

DIGITAL OUTPUT

A-1

Thank you for choosing this Mitsubishi Inverter plug-in option.

This Instruction Manual gives handling information and

precautions for use of this equipment. Incorrect handling might

cause an unexpected fault. Before using the equipment, please

read this manual carefully to use the equipment to its optimum.

Please forward this manual to the end user.

1. Electric Shock Prevention

This section is specifically about

safety matters

Do not attempt to install, operate, maintain or inspect this

product until you have read through this Instruction Manual and

appended documents carefully and can use the equipment

correctly. Do not use this product until you have a full

knowledge of the equipment, safety information and

instructions.

In this Instruction Manual, the safety instruction levels are

classified into "WARNING" and "CAUTION".

Incorrect handling may cause

hazardous conditions, resulting in

death or severe injury.

Incorrect handling may cause

hazardous conditions, resulting in

medium or slight injury, or may cause

only material damage.

The level may even lead to a serious

consequence according to conditions. Both instruction levels

must be followed because these are important to personal

safety.

WARNING

CAUTION

SAFETY INSTRUCTIONS

WARNING

•While power is ON or when the inverter is running, do not

open the front cover. You may get an electric shock.

•Do not run the inverter with the front cover or wiring cover

removed. Otherwise, you may access the exposed high-

voltage terminals and charging part and get an electric shock.

•Even if power is OFF, do not remove the front cover except for

wiring or periodic inspection. You may accidentally touch the

charged inverter circuits and get an electric shock.

•Before wiring or inspection, power must be switched OFF. To

confirm that, LED indication of the operation panel must be

checked. (It must be OFF.) Any person who is involved in

wiring or inspection shall wait for at least 10 minutes after the

power supply has been switched OFF and check that there

are no residual voltage using a tester or the like. The

capacitor is charged with high voltage for some time after

power OFF, and it is dangerous.

•Any person who is involved in wiring or inspection of this

equipment shall be fully competent to do the work.

•The plug-in option must be installed before wiring. Otherwise,

you may get an electric shock or be injured.

•Do not touch the plug-in option or handle the cables with wet

hands. Otherwise you may get an electric shock.

•Do not subject the cables to scratches, excessive stress,

heavy loads or pinching. Otherwise you may get an electric

shock.

A-2

2. Injury Prevention

3. Additional Instructions

Also the following points must be noted to prevent an accidental

failure, injury, electric shock, etc.

1) Transportation and mounting

2) Trial run

3) Usage

4) Maintenance, inspection and parts replacement

5) Disposal

6) General instruction

CAUTION

•The voltage applied to each terminal must be the ones

specified in the Instruction Manual. Otherwise burst, damage,

etc. may occur.

•The cables must be connected to the correct terminals.

Otherwise burst, damage, etc. may occur.

•Polarity must be correct. Otherwise burst, damage, etc. may

occur.

•While power is ON or for some time after power-OFF, do not

touch the inverter as they will be extremely hot. Doing so can

cause burns.

CAUTION

•Do not install or operate the plug-in option if it is damaged or

has parts missing.

•Do not stand or rest heavy objects on the product.

•The mounting orientation must be correct.

•Foreign conductive objects must be prevented from entering

the inverter. That includes screws and metal fragments or

other flammable substances such as oil.

CAUTION

•Before starting operation, each parameter must be confirmed

and adjusted. A failure to do so may cause some machines to

make unexpected motions.

WARNING

•Do not modify the equipment.

•Do not perform parts removal which is not instructed in this

manual. Doing so may lead to fault or damage of the inverter.

CAUTION

•

When parameter clear or all parameter clear is performed, the

required parameters must be set again before starting operations

because all parameters return to the initial value.

•For prevention of damage due to static electricity, nearby

metal must be touched before touching this product to

eliminate static electricity from your body.

CAUTION

•Do not test the equipment with a megger (measure insulation

resistance).

CAUTION

•This inverter plug-in option must be treated as industrial

waste.

Many of the diagrams and drawings in this Instruction Manual

show the inverter without a cover or partially open for

explanation. Never operate the inverter in this manner. The

cover must be reinstalled and the instructions in the inverter

manual must be followed when operating the inverter.

— CONTENTS —

1 PRE-OPERATION INSTRUCTIONS 1

1.1 Unpacking and Product Confirmation .............................................................................................1

1.1.1 Product confirmation.......................................................................................................................................1

1.2 Parts....................................................................................................................................................2

1.3 Specifications.....................................................................................................................................3

2 INSTALLATION AND WIRING 4

2.1 Pre-Installation Instructions .............................................................................................................4

2.2 Installation Procedure .......................................................................................................................4

2.3 Wiring..................................................................................................................................................9

3 PARAMETER LIST 12

4 EXTENSION ANALOG OUTPUT 14

4.1 Wiring Example ................................................................................................................................14

4.2 Internal Block Diagram....................................................................................................................15

4.3 Terminals ..........................................................................................................................................16

4.4 Extension Analog Output Function Parameter List......................................................................17

4.5 Adjustment Procedure ....................................................................................................................18

4.5.1 Setting of analog output signal voltage/current switchover (Pr. 309) ...........................................................18

4.5.2 Calibration of meter ......................................................................................................................................19

4.5.3 Output signal setting.....................................................................................................................................21

4.5.4 Analog signal adjustment [Pr. 307, Pr. 308, Pr. 311, Pr. 312] ......................................................................22

4.6 Instructions ......................................................................................................................................23

5 DIGITAL OUTPUT 24

5.1 Internal Block Diagram....................................................................................................................24

5.2 Terminals ..........................................................................................................................................25

5.3 Digital Output Function Parameter List .........................................................................................26

5.4 Output Signal List ............................................................................................................................27

1PRE-OPERATION INSTRUCTIONS

1.1 Unpacking and Product Confirmation

Take the plug-in option out of the package, check the product name, and confirm that the product is as you

ordered and intact.

This product is a plug-in option dedicated for the FR-E700-SC series (safety stop function model).

1.1.1 Product confirmation

Check the enclosed items.

Plug-in option

.......................................................1

Junction connector .........................1

(Refer to page 5, 7.)

M3 mounting screw

(Long) (M3 ×20mm)......................1

(Short) (M3 ×6mm) .......................1

(Refer to page 5, 7.)

Front cover for plug-in option.........1

(Refer to page 5, 7)

Spacer for plug-in option mounting

...1

(Refer to page 5, 7.)

Hexagon spacer .............................1

(Refer to page 5, 7.)

CAUTION

Install a provided front cover for plug-in option, in place of the inverter front cover.

PRE-OPERATION INSTRUCTIONS

1.2 Parts

AMC

AM0

AM1

Front view

Terminal layout

Rear view

Mounting

hole

Mounting hole

Mounting

hole

Terminal

block

Connector

Connect to the inverter

option slot

(Refer to page 5, 7.)

PRE-OPERATION INSTRUCTIONS

1.3 Specifications

(1) Output signals

Voltage output (across terminals AM0-AMC) 0 to 10VDCMAX

Current output (across terminals AM1-AMC) 0 to 20mADC

(2) Output resolution

Voltage output 3mV

Current output 10

(3) Output accuracy (reference value)

±10% of the full-scale output value

Depends on the output signal type.

(4) Meters used

•Voltmeter

DC voltmeter Full-scale 10V (internal impedance 10kΩor more)

•Ammeter

DC ammeter Full-scale 20mA (internal impedance 300Ωor less)

•Wiring length

Maximum 10m

INSTALLATION AND WIRING

2.1 Pre-Installation Instructions

Make sure that the input power of the inverter is off.

2.2 Installation Procedure

CAUTION

With input power on, do not install or remove the plug-in option. Otherwise, the inverter and

plug-in option may be damaged.

For prevention of damage due to static electricity, touch nearby metal before touching this

product to eliminate static electricity from your body.

CAUTION

•Always perform wiring to the main circuit terminals and control circuit terminals before installing the

option. Wiring cannot be performed after installing the option.

•When mounting the plug-in option, do not let wires get caught in the plug-in option or the spacer for option

mounting. If a wire gets caught, the inverter and the plug-in option may be damaged.

•When the inverter cannot recognize that the option is mounted due to improper installation, etc., " "

(option fault) is displayed.

•Take care not to drop a mounting screws during mounting and removal.

•Pull out the option straight to remove. Otherwise, the connector may be damaged.

REMARKS

•Bcause the voltage class, model name and serial number (only voltage class is labeled for FR-E720-5.5KSC (FR-

E720-240SC), FR-E740-5.5KSC (FR-E740-120SC) or higher) are written on the PU cover, replace the PU cover of

the plug-in option with the removed PU cover of the inverter.

INSTALLATION AND WIRING

zInverter with one front cover

(1) Remove the front cover from the inverter. (For removing the front cover, refer to the FR-E700 series

instruction manual.)

(2) Remove the PU cover from the front cover. Open the PU cover with a driver, etc. and remove it in the

direction of arrow as shown below.

(3) Fit the spacer for plug-in option mounting, the hexagon spacer, and the junction connector into their

designated positions shown in the diagram on the next page. Fit the junction connector along the guide

of the connector of the inverter and insert it as far as it goes.

(4) Fit the connector of the plug-in option along the guide of the junction connector and insert it as far as it

goes.

(5) Fix the plug-in option securely by using the supplied mounting screw (short) to the upper screw hole

and the other supplied mounting screw (long) to the lower screw hole of the plug-in option. If the screw

holes do not line up, the connector may not have been plugged properly. Check for loose plugging.

Tightening torque: 0.33 to 0.4N⋅m

(1) Front cover

(2) PU cover

* Open the PU cover, then open it toward the arrow

direction to remove.

Autres manuels pour FR-A7AY

Table des matières

Autres manuels Mitsubishi Electric Unité de contrôle

Mitsubishi Electric

Mitsubishi Electric NZ2GN2S1-32D Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65SBTB2N-16S Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65VBTCE32-16DT Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manuel d'installation et d'exploitation

Mitsubishi Electric

Mitsubishi Electric GT1030-HBD Instructions d'utilisation et d'entretien

Mitsubishi Electric

Mitsubishi Electric FX-USB-AW Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric L61P Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric EHPT Series Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric GOT1000 GT1595-XTBA Instructions d'utilisation et d'entretien

Mitsubishi Electric

Mitsubishi Electric MELSEC-LD77MS2 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric NZ2MF2S1-32D Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric QJ71DN91 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R60DA4 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric RD81RC96-CA Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-RX40NC6B Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65VBTS32-16DT Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric AJ65FBTA42-16DT Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric QD75MH1 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric GT1695M-XTBA Instructions d'utilisation et d'entretien

Mitsubishi Electric

Mitsubishi Electric GOT SIMPLE GS2110-WTBD Instructions d'utilisation et d'entretien

Mitsubishi Electric

Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric RD81DL96 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric EMU4-CNT-MB Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur